• Steel and Composite Structures
• /
• v.21 no.2
• /
• pp.267-287
• /
• 2016

The seismic performance of the ordinary steel reinforced concrete (SRC) columns has no significant improvement compared to the reinforced concrete (RC) columns mainly because I, H or core cross-shaped steel cannot provide sufficient confinement for core concrete. Two improved SRC columns by constructing with new-type shaped steel were put forward on this background, and they were named as enlarging cross-shaped steel and diagonal cross-shaped steel for short. The seismic behavior and carrying capacity of new-type SRC columns have been researched theoretically and experimentally, while the shear behavior remains unclear when the new-type columns are joined onto SRC beams. This paper presents an experimental study to investigate the shear capacity of new-type SRC joints. For this purpose, four new-type and one ordinary SRC joints under low reversed cyclic loading were tested, and the failure patterns, load-displacement hysteretic curves, joint shear deformation and steel strain were also observed. The ultimate shear force of joint specimens was calculated according to the beam-end counterforce, and effects of steel shape, load angel and structural measures on shear capacity of joints were analyzed. The test results indicate that: (1) the new-type SRC joints display shear failure pattern and has higher shear capacity than the ordinary one; (2) the oblique specimens have good bearing capacity if designed reasonably; and (3) the two proposed construction measures have little effect on the shear capacity of SRC joints embedded with diagonal cross-shaped steel. Based on the mechanism observed from the test, the formulas for calculating ultimate shear capacity considering the main factors (steel web, stirrup and axial compression ratio) were derived, and the calculated results agreed well with the experimental and simulated data.

• Journal of Periodontal and Implant Science
• /
• v.23 no.3
• /
• pp.461-474
• /
• 1993

This study was performed to estimate the effect of plaque control on the progress of the repair pattern of the alveolar bone surface after bone surgery. In this experiment six mongrel dogs were used, four of them were as experimental group and others were as control. In the case of experimental group, dental floss ligature was tied over the neck of crown for permiting of plaque accumulation during one week before surgery and oral hygiene procedures were not performed. In control group, all the surgical intervention was done as same procedure with experimental except oral hygiene program. After surgery plaque was controlled during one week with using the chlorhexidine brushing. Animals were sacrificed at 1,2,4,6 weeks after osseous surgery. The results were as follows : 1. The alveolar bone defects were covered with regenerated epithelium at one week, matrix change of granulation tissue on subcutaneous area was observed, and new bone formation was initiated from the surface of the bone defects. 2. The connective tissue arrangement revealed more dense, new bone formation by osteoblasts was active at 2 weeks and proliferation of gingival epithelium and alveolar bone tissue were evident at 4 weeks, and almostly recovered to normal condition at 6 weeks. 3. In experimental group, inflammatory reaction was persistent in early stage and bone repair was delayed compared to control group. 4. In control group, matrix change of granulation tissue was initiated from one week, regeneration of gingival epithelium and maturation of subcutaneous conective tissue and new bone formation were evident at 2 weeks, so almost normal bone regeneration was observed at 4,6 weeks.

• Korean Institute of Interior Design Journal
• /
• v.24 no.1
• /
• pp.160-168
• /
• 2015

The subject of this research is to analyze the design characteristics of outdoor spaces in Good Design awarded apartment complexes in the past decade. The results are as follows. First, the overall outdoor space design theme, one of the conceptual elements, is focused on both 'nature' and 'story of various subject' that are similar to each other. Second, the case study object with the visual openness, which is secured between apartment blocks, is shown frequently in case box-shaped apartment blocks are arranged in a row. However, in case of Y-shaped block arrangement, the visual openness secured within an apartment complex is considered more important. Third, according to the result of circulation/ inner path element, the most frequently appeared inner path form is a grid pattern with straight path emphasis. While apartment complexes with the parking lot on the ground are only 3 out of 18 cases, it with circulation path for vehicle on the ground level are over 61%. Fourthly, the design characteristic of social space of physical outdoor design appears to be 'central link facility type'. In this case, the central community facilities are more likely to be combined with various functions, such as green, water, and social connection. Fifthly, in case of natural space, most of the apartment cases are shown over 45% green area ratio with wide green and water space provision. Especially, the differentiation is to provide the space where can stimulate a resident's participation.

• Journal of Fashion Business
• /
• v.18 no.4
• /
• pp.66-79
• /
• 2014

Unlike other body arts, body painting illuminates the value of art using eco-friendly formative activity and natural environment and highlights the need of eco-friendly activity. However, although body painting has focused on forming right relationship between human beings and nature, there are few researches which are linked with nature art. Therefore, the purpose of this study is to argue the need to study body painting as nature art in connection with natural environment and analyze body painting according to nature art types. The study methods included both theoretical review and empirical review. The theoretical review examined the concept and characteristics of nature art through previous researches and literature and the empirical review looked into the types and works of nature art and applied them to body painting works. The results were as follows. First, an installation type was possible by arranging and attaching certain materials to the body. Second, a physical type was possible by representing body itself as the part of nature. Third, a symbolic type was possible by making body appearance as a some symbol based on artist's idea. Fourth, a sound type was possible by stimulating auditory hallucination using the nature of objects and sensing a sound. Fifth, an ecological type was possible by conveying the message of living things in nature to the body. Sixth, an interior type was possible by inducing indoor installation of works. Seventh, a poetic type was possible by making one feel a poetic inspiration expressed in nature using the mystery of the sea and a simple sequential pattern of floral leaves. Eighth, a drawing type was possible by adding artist's intentional hand with a pictorical technique. Ninth, a indigenous type was possible by reproducing South American indian's primitive style. The review of this study suggests that body painting works have been expressed in experimental and temporary arrangement like nature art in nature and can be applied according to nine types of nature art.

• The Korea Journal of Herbology
• /
• v.34 no.3
• /
• pp.19-30
• /
• 2019

Objectives : This study is to propose the identification keys based on stereoscopic examination of 8 seed herbs in 2 categories (Phyllolobobii Semen (PS) with 4 Astragali Semen (AS), and 2 Lepidii seu Descurainiae Semen (LDS) with 1 Drabae Semen (DS)) which have difficulties in discrimination with visual observation. Methods : We reviewed the description of original plants and their medicinal parts from the literature. The original plants were collected, identified, confirmed as specimens, and compared to the samples distributed in the market. The first identification was made by visual observation, and insufficient points were supplemented by stereoscopic observation. Identification criteria were set by considering morphological characteristics of authentic herbs, percentage of adulterants, and distinction between authentic herbs and adulterants. Results : The original plants of PS and AS could be distinguished by upright or lying form of stem, color of flowers, number of leaflets, and presence of hair of fruits. LDS and DS could be distinguished by leaf arrangement on stem: radical or cauline, whole plants size, leaf division, color of flowers, and shape of fruits. The herbal medicines of PS and AS could be distinguished by seed surface pattern, size, and hardness. LDS and DS could be distinguished by size, shape, viscosity when chewed, and degree of mucous layer formation when soaked in water. Conclusions : This study suggests the identification keys of original plants and herbal medicines. Especially, since fine seed herbs are difficult to distinguish by visual observation, the stereoscope should be applied to the discrimination.

• The Research Journal of the Costume Culture
• /
• v.31 no.1
• /
• pp.124-140
• /
• 2023

This study analyzes traditional women's Hu costumes of the Tang dynasty, and deploys a creative fashion design to converge contemporary and traditional styles. In this costume, women wear a robe with striped or plain patterns in the lower part of the pants, and it appears frequently in red and yellow colors. Depending on the sleeve, it is either a round collar or a turn down collar robe. In the Hu hat, the huntuomao and juanyanxumao were leather and mili and weimao were used to prevent the sand from flowing. This study uses the CLO 3D program with the "moment" theme based on the Hu costume for women to deploy 4 pairs of fashion design and to produce works for 2 pairs. The 3D virtual clothing program demonstrates important effects in design deployment and pattern arrangement through its efficiency and convenience of clothing production. The CLO 3D program was closely combined with the 2D design and the 3D affect, and it heightened the efficiency in saving the processing time and energy of the sample clothes. Through facilitating the 3D digital fashion design, the production may reduce time needed and contribute to an effective economy, and it may compare digital fashion design to actual products as well as illustrate the potential of digital fashion design.

• Journal of Korean Library and Information Science Society
• /
• v.51 no.2
• /
• pp.245-272
• /
• 2020

The purpose of this study is to analyze the current status of space use in university library and draw up considerations for enhancing space utilization based on the analysis results. For this purpose, the utilization rate of each space was analyzed by categorizing the user's space of the university library, and secondly, the preferences of the major user groups were analyzed according to the characteristics of the users' space. For empirical analysis, we collected and refined users' space usage data (98,282 people's data 433,769 cases) accumulated for one year for the central library of "J" National University. Then we analyzed the usage pattern according to space and period(monthly, hourly). In addition, preferences for each major group of users (undergraduates, graduate students and graduates) in the library were analyzed through the library visitors' data (2,426,553 cases) over the same period. The results of this study can be used as preliminary research for the composition and arrangement of users' space in future university libraries.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.2
• /
• pp.123-130
• /
• 2013

In this paper, the delamination and failures in frequency selected surface(FSS) caused by residual stresses in the FSS embedded hybrid composites due to the difference between the coefficients of thermal expansion of components and the transmission characteristic changes due to deformation of FSS patterns by residual stresses were studied. FSS may have different electromagnetic characteristics depending on the type of element, design variables, and arrangement. Design variables of dipole FSS were determined using PSO(Particle Swarm Optimization) to obtain the transmission characteristic for the target resonant frequency. Subsequently, the design variables of other types of N-pole(tripole, cross dipole, and Jerusalem cross) were determined based on the dimensions of the dipole for the comparisons of residual stresses of FSS embedded composite structures and transmission characteristics. In addition, effects of FSS pattern, and stacking sequence of composite laminates were considered.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.530-537
• /
• 2007

This paper is concerned with the analysis of plastic deformation of bimetal co-extrusion process. Two sets of material combination have been adopted for analysis, i.e. combinations of Cu/Al and Fe/Al. In the first set of material combination, the selected materials are AA 1100 aluminum alloy as hard material and CDA 110 as soft one. This type of material selection is to examine the effect of hard core and soft sleeve and vice versa on the deformation pattern in terms of plastic zone and velocity discontinuity along the contact surface between construction materials. Four different cases of co-extrusion process in terms of material combination and interference bonding were simulated to investigate the effect of material arrangement between core and sleeve, and of bonding on the plastic zones and velocity discontinuity. In the other set of material combination, model materials used as core and sleeve were AA 1100 and AISI 1010, which are relatively soft and hard, respectively. Process parameters except diameter ratio of core to sleeve material such as semi-die angle, reduction in area in global sense and die comer radius have been set constant throughout the simulation to concentrate our effort on the analysis of influence of diameter ratio on deformation behavior such as deformation zone, surface expansion, exit velocity discontinuity between composite materials, and extrusion forces.

• Journal of Forest and Environmental Science
• /
• v.34 no.6
• /
• pp.435-450
• /
• 2018

Phenological events of four Rhododendron tree species (viz. R. arboreum, R. arboreum ssp. delavayi var. delavayi, R. barbatum and R. kesangiae) was monitored in temperate mixed broad-leaved forests of Arunachal Pradesh, India. Phenological events like flower bud formation, flowering, fruit setting, fruit maturing, seed dispersal, leaf bud formation, leaf flushing, and leaf shedding were recorded. Indices i.e., phenophase sequence index (PSI), active phenophasic period of the species (APS) and index of reproductive/vegetative activity (RVA) were also calculated. Present study revealed that bark consistency, growth form and leaf pattern of the studied species have showed variations among the species. Rhododendron species exhibited the phenological events overlapping with other phenophases. The peak flower bud formation was observed during the winter; R. arboreum ssp. delavayi var. delavayi start flowering from December, while the flowering in rest three species exhibited during February to April. Fruit setting occurred during summer to autumn while fruit maturation revealed peak during November. Leaf bud formation illustrated two peaks in April and May, leaf flushing exhibited peak in June, while leaf shedding peaked during October to November. Active phenophasic period of the species were found 12 months, which revealed that species engage in various phenophase activities throughout the year. Phenophase sequence index ranged between 0.8 to 0.9 (PSI ${\geq}0.6$), signifies that species have a sequential arrangement of phenophases. Index of reproductive/vegetative activity of the species exemplified >1, indicate that the reproductive phenophases were dominance over vegetative phenophases. The study have provided substantial insight on the life cycle events of Rhododendron species and ecological approaches for further scientific study with recent climate change and effective management and conservation.