• Steel and Composite Structures
• /
• 제1권1호
• /
• pp.33-50
• /
• 2001

In this paper an experimental study is performed on end-plate type joints. The test arrangement represents a column-base joint of a steel frame. Altogether six specimens were tested, each of them subjected to cyclic loading. The specimens were carefully designed by performing detailed preliminary calculations so that they would present typical behaviour types of end-plate joints. On the basis of the experimentally established moment-rotation relationship, the cyclic characteristics of each specimen have been calculated and compared to one another. The results are evaluated, qualitative and quantitative conclusions are drawn.

• Structural Engineering and Mechanics
• /
• 제10권6호
• /
• pp.589-601
• /
• 2000

A simplified analysis procedure utilizing the strut-tie modeling technique is developed to take a close look into the post-elastic deformation capacity of beam-column connections in ductile reinforced concrete frame structures. Particular emphasis is given to the effect of concrete strength decay and quantity and arrangement of joint shear steel. For this a fan-shaped crack pattern is postulated through the joints. A series of hypothetical rigid nodes are assumed through which struts, ties and boundaries are connected to each other. The equilibrium consideration enables all forces in struts, ties and boundaries to be related through the nodes. The boundary condition surrounding the joints is obtained by the mechanism analysis of the frame structures. In order to avoid a complexity from the indeterminacy of the truss model, it is assumed that all shear steel yielded. It is noted from the previous research that the capacity of struts is limited by the principal tensile strain of the joint panel for which the strain of the transverse diagonal is taken. The post-yield deformation of joint steel is taken to be the only source of the joint shear deformation beyond the elastic range. Both deformations are related by the energy consideration. The analysis is then performed by iteration for a given shear strain. The analysis results indicate that concentrating most of the joint steel near the center of the joint along with higher strength concrete may enhance the post-elastic joint performance.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.147-156
• /
• 1999

Current design code states that the strength reduction factor shall be permitted to be increased linearly from that for axial compression to that for flexure as the design axial load strength $\Phi$cPn decrease from 0.1fckAg to zero. Since this empirically adopted axial load level of $\Phi$cPn=0.1fckAg considers only sectional area and concrete strength, the other variables such as steel ratio, steel yielding strength, and steel arrangement can not be considered. This research is performed to investigate the consistency and the rationality of the code requirement for determination of column design strength. A nonlinear axial force-moment-curvature analysis was conducted in order to investigate the ductility of reinforced concrete column sections. As the result of ductility analysis, it was found that the ductility at the axial force of $\Phi$cPn=0.1fckAg represented a lock of consistency for the various variable contained sections. Therefore, a more reasonable application method of strength reduction factor is proposed, that is based on the strain ductility index.

• Bulletin of the Korean Chemical Society
• /
• 제23권2호
• /
• pp.295-300
• /
• 2002

The construction of the T-shaped post-column flow cell has been changed to enhance the practicability as a UV-visible absorbance detector for capillary electrophoresis. In this new design, a rectangular cube-shaped inner structure is employed, which completely fits the outer rectangular tubing. This arrangement has greatly facilitated the fabrication of the T-cells. In addition, the volume for the auxiliary flow has been dramatically reduced down to 300 ${\mu}L$, and its volume flow rate is optimized at 4.2 ${\mu}L$/min. The short optical path length in the sheath flows (500 ${\mu}m$ on each side) minimizes background absorption, and thus enhances its performance in low-UV wavelengths. We have optimized the auxiliary flow rate at 50 ${\mu}m$/s, so that migration times are insensitive to the flow rate. This optimization has improved repeatabilities in migration times and peak heights. A double-beam detection scheme using a pair of photodiodes is employed to increase the signal-to-noise ratio.

• 한국강구조학회 논문집
• /
• 제25권3호
• /
• pp.233-242
• /
• 2013

현재 가장 많이 사용되는 기존 약축접합부는 브라켓 타입으로 기둥과 보를 접합하는 과정에서 수평 스티프너가 필요하며, 기둥과 브라켓의 용접접합으로 인해 용접량이 비교적 많아 접합부에서 취성파괴가 우려된다. 본 논문은 용접플레이트를 사용함으로써 기존 약축접합부가 가지는 문제점에 대한 해결책을 제시할 수 있는 신형상 약축접합부를 제작해 기존 약축접합부 및 표준 약축접합부와 비교하여 구조성능을 평가하였다. 신형상 약축접합부는 H형강 기둥웨브에서 보 단부사이의 거리를 50mm, 100mm, 150mm, 200mm로 하였다. 실험결과 신형상 약축접합부는 H형강 기둥웨브와 보 단부사이의 거리가 150mm일 때 기준 실험값과 가장 비슷한 것으로 나타났으며, 기존 약축접합부와 표준 약축접합부와 비교해 우수한 구조성능을 가지는 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제23권1호
• /
• pp.13-27
• /
• 2011

본 연구에서는 기하학적 비선형 해석을 통해 완성계 사장교의 주요한 좌굴 거동 특성을 규명하였다. 본 해석 연구에서는 케이블의 자중에 의한 새그효과, 주탑 및 거더의 보-기둥 효과, 그리고 대변위 효과 등의 주요한 기하학적 비선형성이 직접적인 비선형 해석을 통해 고려되었다. 주탑과 거더는 비선형 프레임 요소로 모델링 되었고, 케이블은 비선형 등가 트러스 요소로 모델링 되었다. 차량하중으로 가정된 활하중이 고려되었는데, 활하중 해석 전에 고정하중을 합리적으로 고려하기 위해 초기 형상 해석이 수행되었다. 작용하는 활하중 형태에 따른 주요한 비선형 반응을 케이블 배치 형식에 따라 비교 하였고, 이 후 좌굴 안정성에 큰 영향을 미치는 활하중 형태에 대해 케이블의 배치 형식, 주탑과 거더 간 강성비, 케이블의 단면적, 케이블의 단수 등의 기하학적 특성이 좌굴 모드 및 임계 하중 계수의 변화에 미치는 영향을 규명하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.209-215
• /
• 2017

대형 부유식 파력-해상풍력 복합발전시스템은 정 사각형(폭 150m) 부유식 플랫폼 컬럼 상부에 4기의 3MW 풍력터빈이 설치된다. 전방 풍력터빈으로부터 발생되는 후류는 터빈배치에 따라 후방 풍력터빈의 출력성능과 하중특성에 불리한 영향을 미치므로 후류간섭에 대한 유동해석을 통해 최적배치설계가 실시되어야 한다. 본 논문에서는 플랫폼 배치조건($0^{\circ}$, $22.5^{\circ}$, $45^{\circ}$) 변화에 따른 개별 풍력터빈의 출력특성 및 연간에너지생산량을 확인하기 위해 풍속변화(8m/s, 11.7m/s, 19m/s 25m/s)에 대한 비정상상태 CFD 해석을 실시하였다. 레일리분포를 적용한 연간에너지생산량 계산결과는 각 배치조건에 따라 다르게 나타났으며, 해석결과에 근거하여 후류손실이 최소화 될 수 있는 최적 배치설계를 제안하였다.

• Structural Engineering and Mechanics
• /
• 제19권6호
• /
• pp.653-677
• /
• 2005

Concrete filled steel tubular columns (CFT) are widely used in civil engineering works, especially in large scale of works because of high strength, deformation, toughness and so on. On the other hand, as a kind of strengthening measure for seriously damaged reinforced concrete piers of viaduct in Hansin-Awaji earthquake of Japan in 1995, reinforced concrete piers were wrapped with steel plate. Then, a new kind of structure appeared, that is, reinforced concrete filled steel tubular column (RCFT). In this paper, compression test and bending-shearing test on RCFT are carried out. The main parameters of experiments are (1) strength of concrete, (2) steel tube with or without rib, (3) width-thickness ratio and (4) arrangement of reinforcing bars. According to the experimental results, the effect of parameters on mechanical characteristics of RCFT is analyzed clearly. At the same time, strength evaluation formula for RCFT column is proposed and tested by experimental results and existed recommendations (AIJ 1997). The strength calculated by the proposal formula is in good agreement with test result. As a result, the proposed evaluation formula can evaluate the strength of RCFT column properly.

• Steel and Composite Structures
• /
• 제23권6호
• /
• pp.633-646
• /
• 2017

The compressive behavior of special-shaped concrete filled tube (CFT) mega column coupled with multiple cavities is studied by testing six columns subjected to cyclically uniaxial compressive load. The six columns include three pentagonal specimens and three hexagonal specimens. The influence of cavity construction, arrangement of reinforcement, concrete strength on failure feature, bearing capacity, stiffness, and residual deformation is examined. Experimental results show that cavity construction and reinforcements make it possible to form a combined confinement effect to in-filled concrete, and the two groups of special-shaped CFT columns show good elastic-plastic compressive behavior. As there is no axial bearing capacity calculation method currently available in any Code of practice for special-shaped CFT columns, values predicted by normal CFT column formulas in GB50936, CECS254, ACI-318, EC4, AISCI-LRFD, CECS159, and AIJ are compared with tested values. The calculated values are lower than the tested values for most columns, thus the predicted bearing capacity is safe. A reasonable calculation method by dividing concrete into active and inactive confined regions is proposed. And high accuracy shows in estimating special-shaped CFT columns either coupled with multiple cavities or not. In addition, a finite element method (FEM) analysis is conducted and the simulated results match the test well.

• 콘크리트학회논문집
• /
• 제14권5호
• /
• pp.677-688
• /
• 2002

철근콘크리트 기둥의 비선형 이축모멘트-곡률 관계를 추적할 수 있는 이론모델을 개발하였다. 개발된 모델은 피복콘크리트 박리나 또는 최대하중 후 나타날 수 있는 기둥의 모멘트 저항능력의 취성적인 감소도 모사할 수 있다. 개발된 모델을 이용 기둥의 구성재료 특성과 철근의 기하학적 배치가 PM 상관도와 모멘트-곡률에 미치는 영향에 대하여 변수영향을 고찰하고 철근콘크리트 기둥의 연성은 축하중의 크기, 횡방향 철근의 간격 또는 체적에 가장 큰 영향을 받음이 이론적으로 고찰된 ACI PM-상관도와 비교하여 ACI 내진설계 기준에 따라 횡방향 철근이 배근된 기둥의 경우, 축하중과 모멘트에 대한 : (square root of sum of squares)값이 약 10% 증가하였으며 최대 축하중은 약 20% 정도 증가하였다.