• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.212-219
• /
• 2004

The effect of frequency and amplitude of the OWC (Oscillating Water Column) motion on the nonlinear reaction forces in an air duct arc studied experimentally. Experimental OWC model is idealized as a simple circular cylinder with an orifice type air duct located at the middle of the top rid. Reaction forces due to forced heave oscillation are measured and analyzed. By subtracting the effect of inertia forces and restoring forces, pneumatic damping force and added spring force are deduced. The effects of the frequency and amplitude of the heave motion are discussed. Also, the effects of solidity of the duct on the reaction forces are discussed.

• 콘크리트학회논문집
• /
• 제24권3호
• /
• pp.267-273
• /
• 2012

이 연구에서는 전기로 산화슬래그 골재를 사용한 철근콘크리트 기둥의 휨 성능을 평가하고자 한다. 전기로 산화슬래그는 철 스크랩을 제련하는 과정에서 얻어지는 부산물이다. 전기로 산화슬래그는 천연 광물과 유사한 석회(CaO)와 실리카($SiO_2$)가 주성분이기 때문에 콘크리트용 골재로 이용 가능하다. 이 연구에서는 골재종류를 실험변수로 총 3체의 직사각형 기둥 실험체를 제작하고 휨 실험을 수행하였다. 모든 실험체는 실험구간에서 $250{\times}250$ (mm)의 단면과 1,500 mm의 높이를 가지며, 반복 역대칭 모멘트와 일정한 축력을 받도록 계획하였다. 실험 결과 전기로 산화슬래그 골재를 사용한 실험체가 천연골재를 사용한 실험체보다 동등 이상의 휨 성능을 가짐을 알 수 있었다.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.457-465
• /
• 1988

본 연구에서는 벨트 연삭시 즉 집중하중을 받는 평벨트 구동에서 벨트와 풀리 사이의 내접촉 특성을 구하고자 하였다.준 정적평형(quasi-static equilibrium) 상 태에서 벨트구동계의 이론적 해석을 하여 집중하중점을 포함한 벨트-풀리 전접촉구간 에서 벨트장력분포를 구하고 이 결과를 실험치와 비교하였다. 본 연구에서는 집중하 중점 보다는, 집중하중의 벨트-풀리 전접촉구간에 대한 영향을 밝히는데 주안점을 두 었다.

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.271-277
• /
• 2013

냉간압연 및 소둔공정에서의 조질압연 과정은 강종별로 적정 연신율을 부여함으로서 프레스 가공시 항복점 연신 현상을 제거해주는 중요한 공정이다. 적정 연신율 확보를 위해서는 강종별, 사이즈별 정확한 압연하중 예측이 필수이다. 열간 및 냉간압연과는 달리 조질압연에서는 2%이내의 연신율을 부과하는 공정이므로 압연하중 작용 시 롤 바이트 내 에서의 롤의 탄성변형 거동이 복잡하여 정확한 압연하중을 예측하기가 어려워 예측모델이 정립되어 있지 않다. 그럼에도 불구하고 최근 인장강도 590MPa 급 이상의 자동차용 고강도강 개발이 가속화 됨에 따라 조질압연시 정확한 압연하중의 예측은 더욱더 중요하게 되었다. 따라서 본 연구에서는 조질 압연 시 롤 바이트 내에서 롤의 변형거동이 유사하다고 알려져 있는 호일(foil)압연 이론 식을 이용해 조질 압연 시 전체 생산 강종을 대상으로 압연하중 예측 가능성에 대해 검토하였다. 그 결과 인장강도 350MPa 이상 980MPa 이하의 강종에 대해서는 non circular model 이 circular 모델보다 압연하중 예측 정도가 우수하며, 이 영역에서 압연하중 예측 모델로의 적용이 가능함을 확인하였다.

• 열처리공학회지
• /
• 제36권1호
• /
• pp.22-32
• /
• 2023

In general, when scrap is dissolved in an electric arc furnace, the amount of electric furnace steel dust (EAFD) generated is about 1.5% of the scrap charge amount, and the electric furnace steel dust collected by the bag filter is charged into the Rotary Kiln or Rotary Hearth Furnace (RHF), and the zinc component is recovered as crude zinc oxide, at which time a clinker of Fe-Base is generated. In this research, first, for the efficient resource conversion of electric furnace steel dust, a reduction and roasting experiment was conducted and the reaction kinetics was examined. As a result of the experiment, it was observed that the reduction and roasting reaction was actively conducted in the range of 1100~1150℃, and melting occurred in the range of 1250℃. In the past, this clinker was widely used as a roadbed material for road construction and an Fe-Source for cement production, but in recent years, it has been mainly reclaimed due to strengthening environmental standards. However, landfill treatment is by no means a desirable treatment method due to environmental pollution caused by leachate, expensive landfill costs, and waste of Fe resources. Therefore, in order to more actively recycle the Fe component in the clinker, first of all the clinker was pulverized into an optimal particle size, and anthracite and binder (starch) were added to the magnetic material obtained by specific gravity and magnetic separation for briquet. As a experimental results, it was possible to efficiently separate clinker as Fe component and other slag component by specific gravity and magnetic force. As a results of loading and dissolving the manufactured briquet clinker in an electric arc furnace, it was observed that the unit of power and production yield were clearly improved and the carbon addition effect in molten metal was also somewhat.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.171-173
• /
• 2004

Electromagnetic force is one of the most important factor that effect on metal transfer mode, short-circuit rate, spatter generation rate and mechanical properties of weld metal etc. Also, shielding gas and welding current have influence on metal transfer mode in GMAW. In this paper, different ways for external electromagnetic forces are applied by attaching cylindrically rounded conducting wire solenoid on touch tip holding. With the applied electromagnetic field, the arc transfer mode changes from normal mode to rotating mode and spatter generation decreased in electromagnetic fields(N-pole). In MIG welding, the influences of electromagnetic force on the spatter generation showed different tendency as in the $CO_2$ welding. It is possible reasons were discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.59-61
• /
• 2008

This paper deals with design of Linear Switched Reluctance Motor (LSRM) considering to normal force. First, we derived design factor from pole arc ratio of stator and mover, and calculated time constant using inductance and resistance. Second, we decided design parameter from design factor using time constant, and analyze characteristics for LSRM using finite element analysis. Finally, we analyzed force characteristic according to design factor.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.462-467
• /
• 2010

This paper presents the rotor shape optimization of an interior type permanent magnet (IPM) motor for a reduction of vibration and Electromagnetic Interference (EMI). The vibration and EMI in permanent magnet motors is generated by cogging torque ripple, radial force and commutation torque ripple. Consequently, in order to improve vibration and EMI, the optimal notches are put on the rotor pole with an arc shape proposed. The variation of vibration frequency due to the cogging torque and radial force of each model is computed by the finite element method (FEM). From the analysis result and experiment, we confirmed the proposed model has remarkably improved the vibration and EMI.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.426-426
• /
• 2000

When real robot manipulators arc mathematically modeled, uncertainties are not avoidable. The uncertainties are often nonlinear and time varying, The uncertain factors come from imperfect knowledge of system parameters, payload change, friction, external disturbance and etc. We proposed a class of robust hybrid position/force control of manipulators and provided the stability analysis in the previous work. In the work, we propose a class of adaptive robust hybrid position/force control of manipulators with bound estimation and the stability based on Lyapunov function is presented. Especially, this controller does not need the information of uncertainty bound. The simulation results are provided to show the effectiveness of the algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1451_1452
• /
• 2009

Owing to the increasing number of intelligent homes(or called Smart home), the corresponding cost is much higher. Low voltage circuit breakers are widely used in the intelligent homes to interrupt fault current rapidly and to assure the reliability of the power supply. The distribution of magnetic field induced by arc current in the contact system of molded case circuit breaker depends on the shape, arrangement, and kinds of material of grids. This paper is focused on understanding the interrupting capability, more specifically of the grid and the arc runner, based on the shape of the contact system in the current MCCB. The magnetic driving force was calculated by using the flux densities induced by the arc current, which are obtained by three-dimensional finite element method. There is a need to assure that the optimum design required to analyze the electromagnetic forces of the contact system generated by current and the flux density be present. This is paper present our computational analysis on contact system in MCCB.