• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.122-126
• /
• 1997

the Cu/polyimide system is known to be the best candidate for a multilevel interconnection system due to the low resistance of Cu and to the low dielectric constant of polyimide respectively. Ion beam mixing of Cu(40nm)/polyimide was carried out at room temperature with 80 keV Ar+ and N2+ form $1.5\times$1015 to 15$\times$1015 ions/cm2. The quantitative adhesion strength was measured by a standard scratch test. X-ray photoelectron spectroscopy and x-ray emission spectrocopy are employed to investigate the chemical bonds and the interlayer compound formation of the films Cu/Al/polyimide showed more adhesion strength than Cu/polyimide after ion beam mixing and N2+ ions are more effective in the adhesion enhancement than Ar+ with the same sample geometry. The XES results shows the formation of interlayer compound of CuAl2O4 which can reflect more adhesive Cu/Al/polyimide which has not been reported previously. The latter results is understood by the fact that N2+ ions produce more pyridinelike moiety, amide group and tertiary amine moiety whcih are known as adhesion promotors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.573-576
• /
• 2000

The physical, electrical and piezoresitive characteristics of CrN(chromium nitride) thin-films on silicon substrates have been investigated for use as strain gauges. The thin-film depositions have been carried out by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(5∼25 %)Na$_2$). The deposited CrN thin-films with thickness of 3577${\AA}$ and annealing conditions(300$^{\circ}C$, 48 hr) in Ar-10 % N$_2$deposition atmosphere have been selected as the ideal piezoresistive material for the strain gauges. Under optimum conditions, the CrN thin-films for the strain gauges is obtained a high electrical resistivity, $\rho$=1147.65 ${\mu}$$\Omega$cm, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=11.17.

• Laser Solutions
• /
• v.1 no.1
• /
• pp.30-38
• /
• 1998

This study includes the efface of shielding gas types on $CO_2$ laser weldability of low carbon automotive galvanized steel. The types of shielding gas evaluated are He, $CO_2$, Ar, $N_2$, 50%Ar＋50%$N_2$. The weld penetration, strength, formability(Erichsen test) of Laser weld are found to be strongly dependent upon the types of shielding gas used. Further, the maximum travel speed and flow rate to form a keyhole weld is also dependent upon types of shielding gas. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related with ionization/dissociation potential, which determine the period of plasma formation and disappearance. Further, thermal conductivity and reactivity of gas with molten pool also give strong effect on penetration and porosity formation which in turn affect on the formability and strength.

• Polymer(Korea)
• /
• v.32 no.3
• /
• pp.239-245
• /
• 2008

Block copolymers of the general formula $[(-CO-R'-CO-HN-Ar-NH-CO-R'-CO)_xNH(CH_2)_3-(Me_2SiO)_y(CH_2)_3NH_2]_n$, [n=18.00 to 1175.0] where $R'=CH_2CH(CH_2GeCl_3)$;$CH_2CHGeCl_3CH_2$; and $Ar=-C_6H_4$;$-(o.CH_3C_6H_4)_2$;$-o.CH_3OC_6H_4)_2$;$-(o.CH_3C_6H_4)$ were prepared by a polycondensation reaction of polyamide containing a pendant trichlorogermyl group and terminal acid chloride $Cl(-CO-R'-CO-NH-Ar-NH-CO-R'-CO-)_xCl$ with aminopropyl-terminated polydimethylsiloxane $H_2N(CH_2)_3(Me_2SiO)_y-(CH_2)_3NH_2]$, (PDMS). These polymers were characterized by elemental analysis, $T_g$, FT-IR, $^1H$-NMR, solid state $^{13}C$-NMR, and molecular weight determination. The thermal stability of these copolymers was examined using thermal analysis techniques, such as TGA and DSC. Their molecular weights as determined by laser light scattering technique ranged $5.13{\times}10^5$ to $331{\times}10^5\;g/mol$. These polymers display their $T_g$ in the range of 337 to $393^{\circ}C$ with an average decomposition temperature at $582^{\circ}C$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1211-1214
• /
• 2005

One of the important problems in recent AC-PDP technology is high efficiency. In this research, we have been investigated electro-optical characteristics of MgO protective layer after radio frequency(RF) plasma treatment using Ar, $O_2$, and $H_2$ gases. The breakdown voltage order was $O_2$ > Ar > Nontreatment > $H_2$. Also, brightness order was $O_2$ > Ar > Non-treatment > $H_2$. In this experiment, the best result was obtained after $O_2-plasma$ treatment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.93-99
• /
• 1997

The re quest to develop the engines that are able to run without air or with very little oxygen condition is raised with the interest of ocean science or the mines. This research had already be gun before the world war II, but had been stagnant owing to the appearance of nuclear power. Recycle diesel engines have ability to run under the above mentioned condition the recycle diesel engine recirculates exhaust gases into intake port and consumes additional oxygen supplied by oxygen tank. Carbon dioxide is controlled by the absorber. The combustion and emission characteristics of recycle diesel engines are quite different with conventional one because the working fluids of recycle diesel engines consist of Ar, $CO_2$ and $O_2$ as well as $N_2$. Recycle diesel engine is therefore different with general diesel engine from the viewpoint of intake air composition. It is required to investigate the effect of intake composition in the combustion and emission to know recycle diesel engine. In this study, NOx concentration, smoke and cylinder pressure are measured with the variation of Ar and $CO_2$ Reduces show that the addition of Ar reduces NOx but increases smoke. Otherwise $CO_2$ reduces smoke and NOX simultaneously. Only $CO_2$ increases the ignition delay and both gases increase fuel consumption Ar addition is superior to $CO_2$ addition for the performance of recycle diesel engine system but $CO_2$ has the avantage with respect to emission.

• Journal of Korean Vacuum Science & Technology
• /
• v.4 no.4
• /
• pp.97-101
• /
• 2000

In this study, two kinds of barium strontium titanate (BST) samples were prepared. One is a conventional BST film that is sputtered in a mixture of argon and oxygen. The other is a nitrogen-incorporated BST film that is sputtered in a mixture of oxygen and intentionally added nitrogen instead of argon gas. The structural properties of both of the BST films had not changed significantly with the species of sputtering gas. However, the leakage current of BST films sputtered at ($N_2$+O$_2$) atmosphere was lower than those sputtered at (Ar +O$_2$) atmosphere: 1.9$\times$10$^{-8}$ A/cm$^2$ at 2V for the films prepared at (Ar +O$_2$) atmosphere and 8.6$\times$10$^{-9}$ A/cm$^2$ for the films at ($N_2$+O$_2$) atmosphere. From an XPS analysis, it has been found that nitrogen atoms are incorporated in BST films with a concentration of 1.92 at% and form a certain oxynitride phase. It is proposed that nitrogen atoms are able to fill the oxygen vacancies of BST films during sputtering process, and then the leakage current reduces due to a decrease in the vacancies. The BST films sputtered at ($N_2$+O$_2$) atmosphere have superior electrical properties to the films sputtered at (Ar +O$_2$), without any significant structural changes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.6
• /
• pp.471-478
• /
• 2002

Vacuum evaporated cadmium sulphide (CdS) thin films were implanted with $Ar^+$ and $N^+$ for different doses. The properties of the ion implanted CdS thin films have been analysed using XRD, optical transmittance spectra, and Raman scattering studies. Formation of Cd metallic clusters were observed in ion implanted films. The band gap of $Ar^+$ doped films decreased from 2.385 eV of the undoped film to 2.28 eV for the maximum doping. In the case of $N^+$ doped film the band gap decreased from 2.385 to 2.301 eV, whereas the absorption coefficient values increased with the increase of implantation dose. On implantation of both types of ions, the Raman peak position appeared at $299\textrm{cm}^{-1}$ and the FWHM changed with the ion dose.

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 1986.12a
• /
• pp.514.3-515
• /
• 1986

λP$_{L}$ promoter와 Infiuenza virus의 NS1 Structural gene이 있는 pASl EH801 plasmid를 E. coli host N5' 과 AR120에 각각 transformation하여 온도와 nalidixic acid로 각각 induction 하여 보았다 N5151의 경우, O.D.600 1.2에서 42$^{\circ}C$로 induction하였을 때 maximum productivity를 보였으며 AR120의 경우는 O. D. 600 1.2, 37$^{\circ}C$, 40$\mu\textrm{g}$ nalidixic acid/$m\ell$ induction 하였을 때 maximum yield를 보여주었다. 이때 pH, DO, temperature, $O_2$%, $CO_2$%를 A/D converter통해 computer에 연결시켜 data acquision을 한 결과, 접종 후 ON-line induction이 가능함을 알 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.504-504
• /
• 2012

Gas 종류에 따른 플라즈마 제트 장치의 방전 특성을 조사하였다. 고전압 전극으로 내경 0.26 mm, 외경 0.52 mm인 의료용 바늘을 사용하였으며 바늘을 유리관 내부에 삽입하여 4가지 gas를 주입시킨다. Gas의 종류는 Ar, He, Ne, 그리고 $N_2$이다. Ar과 He의 방전 개시 전압은 각 1.2 kV, 1.0 kV이고 보라색 플라즈마가 방출된다. Ne 방전은 방전 개시 전압 시작 시점인 0.3 kV부터 유리관 밖으로 길게 방출 되며 주황색 플라즈마가 방출된다. 특히, Ne gas는 전기적 쇼크가 전혀 없다. $N_2$ gas는 방전개시전압이 2.0 kV로 가장 어려우며 유리관 밖으로 플라즈마 방출되지 않는다. 각 gas 별 스펙트럼의 특성도 파악하여 어떤 gas가 인체 및 생체에 적합한지 파악한다.