• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.467-470
• /
• 2011

최근 7.7 DDoS 사건과 해킹 사건 등으로 국가기관의 정보보호에 관한 중요성이 대두되고 있고, 정보보호 관련 법률이 국회에서 논의되고 있다. 하지만 국회사무처의 정보보호컨설팅 결과 61.2점으로 매우 낮게 평가 되었으며, H/W, S/W분야의 평가에서도 보안성이 취약한 것으로 나타났다. 본 논문은 입법지원 기관인 국회사무처의 인터넷 네트워크와 사용 시스템 등에 대한 관리적, 기술적, 물리적 보안 요소에 대한 현황을 기밀성, 가용성, 무결성 등의 보안기준에 따라 파악하고, 이를 분석한다. 그리고 입법지원 기관이 갖추어야 할 인터넷 네트워크와 사용 시스템 등에 대한 보안 강화를 위한 설계를 연구한다. 본 연구를 통해 입법지원기관의 보안 현황을 분석하고, 사회적인 책임기관으로서 역할과 보안 강화를 위한 자료를 제공하고자 한다.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.07a
• /
• pp.133-155
• /
• 2002

1. Quasicrystalline powders shows exotic physical and mechanical p properties 2. Applications: structural application: strengthening particles for composites C Coating application: wear resistance, low friction coefficient 3. For thermal spaying: material loss during process should be c considered to control chemical composition of deposit 4. Friction coefficient is strongly dependent on contact geometry F Friction coefficient from pin on plate: 0.1-0.2 Friction coe야icient from flat on plate: about 0.46. 5. Quasicrystalline materials show lower friction coefficient but higher w wear rate than corresponding values of $Cr_20_3$ coated layer. 6. Amorphous coating seems to be promising

• Journal of Korean Institute of Industrial Engineers
• /
• v.25 no.2
• /
• pp.204-216
• /
• 1999

Failure physics and statistical lifetime analysis constitute the two extreme ends of the reliability engineering spectrum, and studies that relate failure mechanisms to failure distributions have been near non-existent. This paper is an attempt to stimulate interest to fill the gap between the two extremes and proposes an approach of combining them through i) developing a failure mechanism model, ii) generating failure times by Monte Carlo simulation with the model, iii) deriving the failure time distribution and evaluating the product reliability, and iv) improving the product reliability by the sensitivity analysis. An application of the proposed approach to the BGA(Ball Grid Array) surface mount package is also provided.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.397-400
• /
• 2004

The design concept for 8kV light triggering thyristor(LTT) with integrated BOD was discussed here in detail. The trade-off between light triggering input source againsthigh dV/dt limitation has been treated via grooved P-base for gate design. The main application point used for high voltage DC transmission(HVDC) was represented.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.3
• /
• pp.101-110
• /
• 2018

In order to The certification of CMMI level is positioned as the most important part of software development company competitiveness. From that point, you will be able to find the various CMMI based process improvement activities of the companies in the above. This paper presents the activity method, such as organization, process application method for the CMMI based process improvement, through the field application. Based on that, this paper enables you to understand the model application method. And we also carry out the application case analysis of defect management with the schedule/effort analysis and colleague's check activity to show the improvement effectiveness, based on the quantitative analysis. And we present the problem and improvement part of real application. The result of this paper will be used to understand the effectiveness of quantitative process management, mentioned in the CMM. And furthermore, we also expect this paper to be useful for the organization to improve the process based on CMM in the future.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.247-250
• /
• 2003

The current paper presents the design and implementation of a low-profile dc-to-dc converter developed as a power supply for the sustain driving: circuit inside large-area wall-mount ac PDP application systems. Details on the design and implementation of a 500 W prototype dc-to-dc converter, miniaturized within a 230 mm$\times$ 130 mm area with a thickness of 25 mm while still achieving a 95 $\%$ conversion efficiency, are presented to demonstrate the feasibility and application potentials of the proposed low-profile dc -to-dc converters.

• Restorative Dentistry and Endodontics
• /
• v.30 no.6
• /
• pp.435-441
• /
• 2005

The purpose of this study was to evaluate the effect of increasing application time of single bottle adhesives (SBA) to microtensile bond strength (MTBS) of dried dentin. To expose the superficial dentin surfaces, human molars were sectioned perpendicular to the long axis of tooth. $32\%$ phosphoric acid gels were applied for 15s and rinsed. The teeth were randomly assigned to 3 groups ; S group (Single Bond), O group (One-Step), P group (Prime & Bond NT). Each group was divided to 3 subgroups (W: dentin wipe with wet gauge and light cured immediately, D, dentin dried for 30s and light cured immediately, 30: dentin dried for 30s and light cured after applying SBA for 30s). Composite resin was built up on the dentin surface and sectioned to obtain 20 specimens with $1mm^2$ cross sectional area and the MTBS was measured. For Single Bond, the mean MTBS of S-W and S-30 group were higher than that of S-D group statistically (P<0.05). For One-Step, the mean MTBS of O-D group was statistically lower than that of O-W group (P<0.05). For Prime & Bond NT, the mean MTBS of P-30 group was statistically lower than that of P-D group (P<0.05).

• Solar Energy
• /
• v.18 no.1
• /
• pp.19-25
• /
• 1998

This paper describes a design method and characteristics analysis of the 3 kW grid-connected photovoltaic power generation system to establish the basic application technology of photovoltaic systems. The design specification of a 3 kW photovoltaic power generation system including a DC/AC inverter is suggested to investigate the system performance for grid connection. The results of the demonstration test from February to October show that the system with utilization rate up to 17% has reliable operation characteristics and is useful for peak-shaving of utility power.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.18 no.3
• /
• pp.235-242
• /
• 1998

This experiment was carried out to determine agronomic characteristics, nutritive value and yield (DM, CP) of Winter Rye as affected by different slurry application on the basis of N contents respectively and was arranged as a randomized complete block design with seven treatments (chemical fertilizer 160kg Nha, cattle sluny 160 . 320 480kg Nha, swine slurry 160 . 320 480kg Nha) and conducted at National Livestock Research Institute, RDA, in Suweon 6om Sep. 1996. to Apr. 1997. The results obtained are summarized as follows : Plant height and leaf length was influenced by slurry application, was orderly ranked cattle sluny 480kg N1 ha > chemical fertilizer 160kg Nha > swine slurry 480kg Nha. Tiller number was increased with cattle slurry application, especilly, the effect of cattle slurry 480kg Nha was obvious but plot of swine slurry tended not to be regular. Crude protein content of rye increased as slurry application level was increased (p< 0.05), but not significant difference was found ADF and NDF content of rye. RFV(Re1ative Feed Value) of rye as affected by slurry application was classified as Grade 2 in all treatments at harvest, according to the forage quality standard assigned by AFGC. Dry matter yield was shown fiom 4,006 kgha to 8,037 kgha as affected by cattle slurry application, in the case of swine slurry application was shown ffom 4,594 kgha to 6,230 kgha (p< 0.05).

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2005.05a
• /
• pp.132-137
• /
• 2005

Installation art(I.A.), which has appeared since 1940s against the loss of human nature and hackneyed art caused by materialism, is in pursuit of contact with audience and various artistic experiments. Many features of I.A. - to try contact with audience, to do experiments connecting different genres of art, to regard time and nature as elements of art and to use high technology - could give good ideas for contemporary display(S.W.D.) design. This study is a basic work to suggest new S.W.D. design through artistic principles of I.A.. First, I.A. and S.W.D. design were studied theoretically. Next, spatial expressions were extracted from I.A. and the case study was proceeded to seek the co-relationship of spatial expressions and display design. For a case of Shiseido, it could be evaluated very high because it adapted spatial expressions of I.A. successively. The S.W.D design could be more effective presentation when it has close contact with audience and various experimetal and artistic ways of Installation art.