• 한국세라믹학회지
• /
• 제16권2호
• /
• pp.83-88
• /
• 1979

The Anorthite is useful compound for some ceramic industries but it is difficult to produce Anorthite because of its high melting point (1553$^{\circ}C$) and narrow firing range. On this study, glass frit was added to Anorthite batch composition to widen firing range and lower melting point. After mixing a glass frit $(Na_2O-CaO-6SiO_2)$ with Anorthite, it was melted and quenched. Ratio of Anorthite vs. glass frit was 9 : 1, 8.5 : 1.5, 8 : 2, 7.5 : 2.5, 7 : 3. In those batch composition added amount of $No_2O$ were between 1.3wt.% and 3.9wt.%. To find the thermal change of the quenched, D.T.A. was surveyed. The quenched were fired at various vitrification temperature and detected by X-Raydiffraction analysis. With addition of glass frit, firing range and vitrification temperature of Anorthite was 100~15$0^{\circ}C$ and 1050~115$0^{\circ}C$ respectively. Optimum amount of glass frit was 20wt.% for the upper mentioned.

• 한국전기전자재료학회논문지
• /
• 제23권11호
• /
• pp.864-868
• /
• 2010

Among LTCC material for substrate, the crystallized anorthite system was mainly studied as high strength material. However, specific factors that have affected on strength of material were studied insufficiently on anorthite system. In this study, the composition of anorthite glass was Ca-Al-Si-Zn-O. The changes of phase and microstructure were observed with the amount and the particle size of glass and the sintering temperature. It was studied that the factors affected on the strength of material. Phases of anorthite and $ZnAl_2O_4$ were formed with the increase of sintering temperature. The $Al_2O_3$ phase was increased with $Al_2O_3$ amount, acted as filler, and the strength of material is increased with $Al_2O_3$ phase. But phases of anorthite and $ZnAl_2O_4$ didn't affect on the strength of material. In the case of 60 vol% glass amounts and below $3.2\;{\mu}m$ of glass particle size, the strength of material was decreased. It is thought that the decrease of strength was due to non-homogeneous mixing between glass powder and filler.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 추계학술발표대회 및
• /
• pp.86.2-86.2
• /
• 2007

• 한국세라믹학회지
• /
• 제36권11호
• /
• pp.1243-1251
• /
• 1999

Densification behavior and microstructural evolution during the liquid-phase sintering of alumina-anorhite system were investigated as a function of MgO addition. When MgO component was added in either alumina or anorthite glass powder the aspect ratio of alumina grains decreased and concurrently the are of flat interface which was formed as a result of contact solid alumina gains rather increased. Consequently addition of MgO component in the Al2O3-amorthite system brought about suppression of the rearrangement of solid grains during the liquid phase sintering and then densification of specimens was also retarded.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.21-21
• /
• 2009

후막 광식각 기술을 이용하여 형성된 Ag 전극과 LTCC 기판 사이의 접착력을 향상시키기 위하여 무기 바인더로서 anorthite, diopside 및 MLS-62 glass frit을 첨가하여 감광성 Ag paste를 제조하였다. 소성 후의 glass pool effect를 감소시키기 위해 attrition mill을 통하여 미세 glass 분말을 준비하였다. Glass frit은 Ag powder의 5vol%~25vol%의 함량으로 첨가하여 감광성 Ag paste를 제조하였고 패턴 형성 후 $850^{\circ}C$에서 1시간 소결하였다. 전극과 기판 사이의 접착력은 micro-ball shear test 법으로 측정하였으며, Ag 전극 부착력은 glass frit의 함량 증가에 따라 증가하다가 감소하는 경향을 보이는데, 이는 과량의 glass frit 첨가로 인한 전극 내부에 액상 풀의 형성에 기인한 것으로 보여진다. Ag 전극의 면저항은 glass frit의 함량이 증가함에 따라 $0.13m{\Omega}{/\square}$에서 $2.06m{\Omega}{/\square}$까지 증가하는 경향을 나타내었다. 소성 전후의 전극 패턴의-수축율은 $100{\mu}m$의 선폭을 기준으로 glass frit의 첨가랑이 증가할수록 43.3%에서 35.0%로 감소하였으며, 그 결과 최소 선폭 $25{\mu}m$의 미세 전극 패턴의 형성이 가능하였다.

• 한국세라믹학회지
• /
• 제54권1호
• /
• pp.55-60
• /
• 2017

An anorthite-based traditional ceramic was developed by adding secondary flux materials to a mixture of kaolin and $CaCO_3$ in order to minimize the deformation during the sintering process. Three flux materials, feldspar, talc, and frit, were evaluated by comparison with two commercial chinaware bodies. Anorthite body with glass frit exhibited poor firing shrinkage. Poor mechanical properties (modulus of rupture, MOR < 30 MPa) was observed for the bodies with feldspar. Another anorthite body was formulated with wollastonite as a Ca source. The fired body showed a MOR of 81 MPa and a shrinkage rate of 6% when wollastonite was added up to 50%. In the XRD analysis, the phase ratio between anorthite and quartz was the highest in the specimen with 50% wollastonite addition. Homogeneous and relatively small closed pores were observed in the microstructural analysis. These results suggest that a ceramic body formulated with 50% kaolin and 50% wollastonite can be fired at $1200^{\circ}C$ with a 6% firing shrinkage rate, giving rise to minimal sintering deformation.

• 한국세라믹학회지
• /
• 제29권7호
• /
• pp.558-564
• /
• 1992

The effect of composed phase in the hot pressed CaO-MgO-Al2O3-SiO2 glass-ceramic has been investigated through microstructure studies, thermal, physical and mechanical properties. Sintering was done in the condition at the temperature range 900~95$0^{\circ}C$ for 20~120 mins under 7.5 MPa unilateral pressure. Sintered ceramics were composed of diopside, anorthite, residual glass and the portion of each phase was dependent on the sintering temperature and the holding time: as the temperature increases, the amount of diopside increased and then the rate of increase of diopside reduced with increasing anorthite. The thermal expansion coefficient of hot pressed was reduced with increasing crystallinity of hot pressed and was in the range of 6.69~7.46$\times$10-6 K-1 below $600^{\circ}C$. The elastic constant of hot pressed increased with increasing crystallinity up to about 80%, but after that was reduced due to the change of microstructure. The flexural strength of sintered ceramics was decreased with higher temperature and holding time, while the fracture toughness of those increased. It was shown that the physical and mechanical properties of hot pressed ceramic were related to the fraction of composed sintered ceramics, similar to a particulate composite, to the crystallinity of 80% of the glass-ceramic.

• 대한의용생체공학회:의공학회지
• /
• 제15권2호
• /
• pp.189-194
• /
• 1994

Effects of ${AI_2O_3}/{P_2O_5}$ ratio on the crystallization of a series of glasses with the nominal composition of 41.4wt % $SiO_2$, 35.0wt % CaO, 20.6wt % (${P_2O_5}$+${AI_2O_3}$) and 3.0wt% MgO were investigated with DTA, XRD and SEM. The major crystalline phases are apatite and anorthite. The glass transition temperature ($T_g$) and the softening point ($T_s$) are shifted to the upper temperature by increasing $AI_2O_3$ content. The temperature of apatite crystallization ($T_{p1}$) is increased by $AI_2O_3$ content, but the tempera¬ture of anorthite crystallization ($T_{p2}$) is not affected significantly. With increased of $AI_2O_3$, the apatite crystallization is decreased, but anorthite crystallization is increased.

• 한국세라믹학회지
• /
• 제31권12호
• /
• pp.1545-1551
• /
• 1994

Various kinetic parameters of the nucleation and crystallization in anorthite glass (CaO.Al2O3.2SiO2) were calculated by nonisothermal differential thermal analysis. Base glass and glass with TiO2 were prepared by melting. In base glass, the temperature where nucleation can occur ranges from 85$0^{\circ}C$ to 9$25^{\circ}C$ and the temperature for maximum nucleation was 900$\pm$5$^{\circ}C$. In glass with TiO2, the nucleation temperature range was 800~875$^{\circ}C$ and the maximum nucleation temperature was 850$\pm$5$^{\circ}C$. Kissinger equation, Bansal equation, and modified Ozawa equation were used for calculating activation energy for crystallization, Ec. The results showed the same activation energies for both glasses with and without TiO2 in the different equations. The shape of maximum exotherm peak and Ozawa equation were used for Avrami exponent, n. The n value for each glass was 2, indicating that each glass crystallized primarily by bulk crystallization.

• 마이크로전자및패키징학회지
• /
• 제18권4호
• /
• pp.63-70
• /
• 2011

Anorthite forming glass frits in amounts up to 25 vol% of the silver powder were added to improve the adhesion between the conductor pattern formed by thick film photoimageable process and the low temperature co-fired ceramics (LTCC) substrate. The sheet resistance of the conductor pattern was raised from 0.13 ${\Omega}/{\square}$ to 2.25 ${\Omega}/{\square}$ as the volume percentage of glass frit increased up to 25 vol%. The adhesion strength was improved with this glass frit increase, but it decreased when the glass content exceeded 20 vol% which are possibly attributed to the liquid pool effect and the reduced fracture toughness in the interface between conductor and LTCC layer. The shrinkage of the width of the conductor pattern decreased with the addition of glass contents.