• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.229-231
• /
• 2004

다층 용접이 적용되는 후판 조립 부재에서는 각 조립단계별로 용접변형이 필연적으로 발생되고 있으며 용접변형의 교정을 위한 추가 작업도 각 조립간계 및 후 공정에서 반복적으로 수행되고 있다. (중략)

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.292-294
• /
• 2006

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.232-233
• /
• 2004

강구조물 제작 시 용접프로세스에 의해 용접부 근방에 불균일한 온도분포가 발생하여 용접변형이 발생된다. 이러한 용접변형은 좌굴강도와 피로강도를 저하시킬 뿐 아니라 구조물의 크기와 형상을 변화시켜 이를 교정하거나 수정하기 위해 추가작업을 실시해야함으로 생산성을 저하시키는 주요한 요인이 되고 있다. (중략)

• 치과방사선
• /
• 제21권2호
• /
• pp.415-423
• /
• 1991

This study was performed to evaluate the geometric standardization of periapical intraoral radiography. Image distortion was measured by analysing serial radiography obtained from dry skull using 5 types of bite registration device. After 16 weeks, the angular distortion of Pattern resin was 0.26±0.14 degree(Horizontal angle 0.17±0.14, Vertical angle 0.16±0.11) which was the lowest among the 5 registration device, and that of putty type Exaflex was 0.49±0.35 degree(Horizontal angle 0.42±0.35, Vertical angle 0.17±0.13) which was the highest. The mean amount of distortion variance of Tooth shade acrylic at each experimental period was 0.06±0.08 which was the lowest among the 5 registration device, and that of XCP alone was 0.ll±0.13 which was the highest.

• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.1-6
• /
• 2013

In carrying out the elastic-plastic analysis, four conditions (equilibrium equation, constitutive equation, condition of compatibility and yield condition) should be satisfied. In welding, the temperature largely changed from a melting temperature to a room temperature. So, yield stress of materials largely changed, too. In particular, yield stress becomes about zero over $700^{\circ}C$. The analysis should be carried out under the condition that equivalent stress generated in temperature increment ${\Delta}T$ did not exceed yield stress of materials at high temperature over $700^{\circ}C$. It should be sufficiently recognized that the obtained results were not reliable if this condition was not satisfied.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.291-293
• /
• 2005

The purpose of this study is to evaluate the effects of line heating variables for forming the curved plate on the behavior of distortion using FEA and experiment. The optimum mixed ratio and standoff for flame heating was established under the heating conditions given in this study. With the heating condition, the predictive equation of angular distortion and transverse shrinkage was established using FEA and verified by comparing the predicted results and experimental results.

• Journal of Electrical Engineering and Technology
• /
• 제3권1호
• /
• pp.79-87
• /
• 2008

This paper proposes the design and implementation of a direct torque controlled induction motor drive system. The method is based on control of decoupling between amplitude and angle of reference stator flux for determining reference stator voltage vector in generating PWM output voltage for induction motors. The objective is to reduce electromagnetic torque ripple and stator flux droop which result in a decrease in current distortion in steady state condition. In addition, the proposed technique provides simplicity of a control system. The direct torque control is based on the relationship between instantaneous slip angular frequency and rotor angular frequency in adjustment of the reference stator flux angle. The amplitude of the reference stator flux is always kept constant at rated value. Experimental results are illustrated in this paper confirming the capability of the proposed system in regards to such issues as torque and stator flux response, stator phase current distortion both in dynamic and steady state with load variation, and low speed operation.

• 대한기계학회논문집A
• /
• 제39권7호
• /
• pp.707-712
• /
• 2015

용접변형은 용접 시 구조물 내에서의 불균일한 온도분포특성으로 인하여 필연적으로 유발되는 현상이다. 또한 용접변형이 발생된 용접구조물의 일부를 제거하는 과정에서 구조물내의 용접잔류응력과 강성의 연속적인 변화에 따라 추가적인 변형이 발생하여 변형의 재분포가 이루어진다. 특히, 이러한 현상은 선박의 제조과정 중 대형블럭을 옮기기 위해 설치된 러그의 절단과정에서 살펴볼 수 있다. 용접구조물의 부분 제거 시 발생되는 변형의 재분포는 절단공구의 파손 등의 문제를 야기하기도 한다. 본 논문은 실험을 통하여 용접구조물의 부분 제거에 따른 용접변형의 재분포가 어떠한 양상으로 발생되는지 연구하기 위한 것이다. 실험을 위해 필릿용접을 실시하였고, 용접된 리브의 일부를 제거함에 따라 발생되는 종굽힘과 각변형을 측정하여 비교 및 분석하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.121-126
• /
• 2003

This paper is concerns with the development of the formulae to predict deformation of curved plate due to line heating. For this purpose thermal elasto-plastic analysis has been carried out for both flat and curved plate models with varying parameters which affect the result of line heating. based on the results of numerical analysis, the formulae for predicting angular deformation has been derived through the regression analysis, which. It has been seen that the present model well agrees with the numerical analysis results and can reflect the curvature effect of plate to be heated. This paper ends with some comments on this formulae.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2005년도 특별논문집
• /
• pp.177-184
• /
• 2005

This paper is concerns with the development of the formulae to predict deformation of curved plate due to line heating. For this purpose thermal elasto-plastic analysis has been carried out for both flat and curved plate models with varying parameters which affect the result of line heating. based on the results of numerical analysis, the formulae for predicting angular deformation has been derived through the regression analysis, which. It has been seen that the present model well agrees with the numerical analysis results and can reflect the curvature effect of plate to be heated. This paper ends with some comments on this formulae.