• Geomechanics and Engineering
• /
• 제29권1호
• /
• pp.25-40
• /
• 2022

In this study, 3D coupled-consolidation numerical parametric study was conducted to predict the deformation mechanism of a 20 storey building sitting on (4×4) piled raft (with length of piles, L_p=30 m) to adjacent 6 m diameter (D) tunnelling in stiff clay. The influences of different tunnel locations relative to piles (i.e., z_t/L_p) were investigated in this parametric study. In first case, the tunnel was excavated near the pile shafts with depth of tunnel axis (z_t) of 9 m (i.e., z_t/L_p). In second and third cases, tunnels were driven at z_t of 30 m and 42 m (i.e., z_t/L_p = 1.0 and 1.4), respectively. An advanced hypoplastic clay model (which is capable of taking small-strain stiffness in account) was adopted to capture soil behaviour. The computed results revealed that tunnelling activity adjacent to a building resting on piled raft caused significant settlement, differential settlement, lateral deflection, angular distortion in the building. In addition, substantial bending moment, shear forces and changes in axial load distribution along pile length were induced. The findings from the parametric study revealed that the building and pile responses significantly influenced by tunnel location relative to pile.

• 대한토목학회논문집
• /
• 제30권2C호
• /
• pp.77-84
• /
• 2010

연약지반에 지하차도의 기초로서 심층혼합처리공법을 적용하였다. 개량체는 실내배합실험으로 구한 배합비와 강도기준을 만족하는 치환율을 적용하였다. 개량체와 지반의 강성비 및 타설중심거리를 변화시키며 개량체와 지반에 발생한 응력 및 변위를 분석하였으며 지하차도의 부등침하에 미치는 영향을 분석하였다. 구조물의 침하기준과 부등침하를 만족하는 치환율은 10~35%이다. 강성비를 변화시킨 결과 강성비차가 30이상인 경우에는 응력집중 때문에 개량체에 769.2kPa까지 발생하여 기준을 초과한다. C.T.C가 5m인 경우에 지반으로 응력이 전이되어 응력이 커지기 때문에 설치간격을 고려하여야 한다. 복합지반강도 정수를 산정하여 수치해석 한 결과 연직침하는 0.6~1.56cm, 각변위 1/909~1/510이다.

• The Plant Pathology Journal
• /
• 제25권1호
• /
• pp.86-90
• /
• 2009

In November 2008, typical powdery mildew symptoms were observed on leaves of Arabidopsis thaliana ecotype Col-0 plants in a growth room under controlled laboratory conditions at Korea University, Seoul. The disease was characterized by the appearance of white powder-like fungal growth on the surface of infected leaves. As the disease progressed, infected leaves exhibited chlorotic or necrotic brown lesions, and leaf distortion and senescence. Conidiophores of the causal fungus were hyaline, unbranched, 3-4 celled, cylindrical, and $80-115{\times}6-9{\mu}m$ in size. Singly produced conidia (pseudoidium type) were hyaline, oblong to cylindrical or oval in shape, and $26-55{\times}15-20{\mu}m$ in size with a length/width ratio of average 3, angular/rectangular wrinkling of outer wall and no distinct fibrosin bodies. Appressoria on the hyphae were multi-lobed. These structures are typical of the powdery mildew Oidium subgenus Pseudoidium, anamorph of the genus Erysiphe. The measurements of the fungal structures coincided with those of Erysiphe cruciferarum. The phylogenetic analysis using ITS rDNA sequences revealed that the causal fungus Erysiphe sp. KUS-F23994 is identical to E. cruciferarum. The isolated fungus incited powdery mildew symptoms on the inoculated Arabidopsis leaves, which proved Koch's postulates. Taken all data together, we first report the occurrence of powdery mildew disease of A. thaliana caused by Erysiphe cruciferarum in Korea.

• 한국산학기술학회논문지
• /
• 제15권12호
• /
• pp.7324-7330
• /
• 2014

미약한 광원 및 조명이 존재하는 환경에서 획득된 저조도 영상에는 많은 색 왜곡이 발생한다. 이러한 색 왜곡은 해당 비전 시스템의 성능 저하를 발생시킬 수 있는 원인이 된다. 따라서 저조도 영상의 원래 색을 찾는 과정은 비전 시스템의 성능 향상을 위한 중요한 과정이다. 이를 위해 본 논문에서는 저조도 영상을 대상으로 한 이색도 반사 모델 기반의 색 복원 기법을 제안한다. 제안한 기법은 이색도 반사 모델을 기반으로 저조도 영상을 확산 반사와 정반사의 영향을 받는 영역으로 구분한다. 이후 각 영역에 미치는 조명 효과를 제거하기 위하여 grey world 기법과 MSRCR 기법을 적용한다. 마지막으로, 두 기법을 적용하여 생성된 결과 영상에 대해 위치별 가중치를 이용하여 두 영상을 조합하여 최종 결과 영상을 생성한다. 본 논문에서는 성능 평가를 위하여 저조도 합성 영상을 사용하였고, 유클리드 거리 및 각 오차를 성능 평가 요소로 활용하였다. 또한 기존에 연구되었던 다양한 기법과의 성능 비교를 수행하여 성능 평가의 객관성을 확보하였다. 다양한 영상 셋을 이용한 실험에서 제안한 기법은 기존의 기법들에 비해 두 성능 평가요소 관점에서 GTD 영상에 가까운 색 복원이 가능함을 보였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.97-97
• /
• 2009

The use of thin plate increases due to the need for light weight in large ship. Thin plate is easily distorted and has residual stress by welding heat. Therefore, the thin plate should be carefully joined to minimize the welding deformation which costs time and money for repair. For one effort to reduce welding deformation, it is very useful to predict welding deformation before welding execution. There are two methods to analyze welding deformation. One is simple linear analysis. The other is nonlinear analysis. The simple linear analysis is elastic analysis using the equivalent load method or inherent strain method from welding experiments. The nonlinear analysis is thermo-elastic analysis which gives consideration to the nonlinearity of material dependent on temperature and time, welding current, voltage, speed, sequence and constraint. In this study, the welding deformation is analyzed by using thermo-elastic method for PCTC(Pure Car and Truck Carrier) which carries cars and trucks. PCTC uses thin plates of 6mm thickness which is susceptible to welding heat. The analysis dimension is 19,200mm(length) * 13,825mm(width) * 376mm(height). MARC and MENTAT are used as pre and post processor and solver. The boundary conditions are based on the real situation in shipyard. The simulations contain convection and gravity. The material of the thin block is mild steel with $235N/mm^2$ yield strength. Its nonlinearity of conductivity, specific heat, Young's modulus and yield strength is applied in simulations. Welding is done in two pass. First pass lasts 2,100 second, then it rests for 900 second, then second pass lasts 2,100 second and then it rests for 20,000 second. The displacement at 0 sec is caused by its own weight. It is maximum 19mm at the free side. The welding line expands, shrinks during welding and finally experiences shrinkage. It results in angular distortion of thin block. Final maximum displacement, 17mm occurs around welding line. The maximum residual stress happens at the welding line, where the stress is above the yield strength. Also, the maximum equivalent plastic strain occurs at the welding line. The plastic strain of first pass is more than that of second pass. The flatness of plate in longitudinal direction is calculated in parallel with the direction of girder and compared with deformation standard of ${\pm}15mm$. Calculated value is within the standard range. The flatness of plate in transverse direction is calculated in perpendicular to the direction of girder and compared with deformation standard of ${\pm}6mm$. It satisfies the standard. Buckle of plate is calculated between each longitudinal and compared with the deformation standard. All buckle value is within the standard range of ${\pm}6mm$.

• 한국지반신소재학회논문집
• /
• 제12권3호
• /
• pp.43-53
• /
• 2013

우리나라 지반공학 기술의 발달로 지반굴착 공사가 대규모로 수행되고 있으나, 지반굴착시 공사현장 또는 인접구조물에 직,간접적인 피해를 유발하는 사고는 여전히 빈번히 발생하고 있다. 특히 주거시설이나 상업시설이 밀집해 있는 도심지의 지하터널, 도시철도 역사, 대규모 상업시설, 초고층 빌딩의 기초 공사 등으로 인한 지반굴착관련 사고가 빈번히 발생하고 있어 경제적인 손실 뿐 아니라 인명피해가 발생하여 사회적인 비용이 급속히 증가하고 있는 실정이다. 본 연구에서는 빈번히 발생하는 개착식 흙막이 굴착관련 사고를 방지하기 위하여 최근 발생한 개착식 흙막이 굴착공사로 인한 다수의 사고 및 인접시설물에 영향을 끼친 사례를 수집, 분석을 수행하여 사고발생 원인에 대하여 고찰하고, 수치해석기법을 사용하여 국내 대표적인 지반조건(내륙, 해안특성) 및 공사공법에 따른 굴착시 영향 분석을 수행하였다. 25건의 사고사례를 분석한 결과, 주요 영향요인으로 지반조사의 부실, 가시설 구조체의 불안정 및 지하수의 처리 미흡 등으로 나타났으며, 이 외 여러 요인들이 복합적으로 작용하여 굴착현장에 문제를 발생시키는 것으로 나타났다. 국내의 대표적인 지반조건 및 시공경향을 고려한 22개의 case에 대한 수치해석결과는 일반적인 내륙지역에서는 차수공법에 비해 배수공법에서 침하가 크게 발생하고, 연약지반 및 암반의 불연속면이 발달한 지역에서는 earth anchor 공법 적용시 면밀한 검토가 필요하며, 압밀이 진행 중인 점토지반에서는 과잉간극수압에 대한 고려가 반드시 필요한 것으로 나타났다.

• Imaging Science in Dentistry
• /
• 제50권3호
• /
• pp.227-236
• /
• 2020

Purpose: Image artifacts caused by patient motion cause problems in cone-beam computed tomography (CBCT) because they lead to distortion of the 3-dimensional reconstruction. This prospective study was performed to quantify patient movement during CBCT acquisition and its influence on image quality. Materials and Methods: In total, 412 patients receiving CBCT imaging were equipped with a wireless head sensor system that detected inertial, gyroscopic, and magnetometric movements with 6 dimensions of freedom. The type and amplitude of movements during CBCT acquisition were evaluated and image quality was rated in 7 different anatomical regions of interest. For continuous variables, significance was calculated using the Student t-test. A linear regression model was applied to identify associations of the type and extent of motion with image quality scores. Kappa statistics were used to assess intra- and inter-rater agreement. Chi-square testing was used to analyze the impact of age and sex on head movement. Results: All CBCT images were acquired in a 10-month period. In 24% of the investigations, movement was recorded (acceleration: >0.10 [m/s²]; angular velocity: >0.018 [°/s]). In all examined regions of interest, head motion during CBCT acquisition resulted in significant impairment of image quality (P<0.001). Movement in the horizontal and vertical axes was most relevant for image quality (R²>0.7). Conclusion: Relevant head motions during CBCT imaging were frequently detected, leading to image quality loss and potentially impairing diagnosis and therapy planning. The presented data illustrate the need for digital correction algorithms and hardware to minimize motion artefacts in CBCT imaging.