• Transactions of Materials Processing
• /
• v.25 no.6
• /
• pp.379-389
• /
• 2016

As a stator for steam turbine diaphragm, hollow-type nozzle stator to substitute for conventional solid one is introduced in this study. This hollowed stator can be separated into two parts such as upper and lower plates with large and curved surface area. This study focuses on thick plate forming process for the upper plate of the hollow-partitioned nozzle stator. First, to reduce forming defects such as under-cut and localized thinning of the deformed plate, and to avoid tool interruption between forming punch and lower die, tool design including the position determination of forming surfaces is performed. Uni-axial tensile tests are carried out using SUS409L steel plate with initial thickness of 5.00mm, and plastic strain ratio (r-value) is also obtained. Due to the asymmetric curved configuration of the upper plate, it is hard to adopt a series of blank holder or draw-bead, so the initial plate during this thick plate forming experiences unstable and non-uniform contact. To easy this forming difficulty and find suitable tool geometry without sliding behavior of the workpiece in the die cavity, two geometric parameters with respect to each shoulder angle of the lower die and the upper punch are adopted. FE models with consideration of 21 combinations for the geometric parameters are built-up, and numerical simulations are performed. From the simulated and predicted results, it is shown that the geometric parameter combinations with ($30^{\circ}$, $90^{\circ}$) and ($45^{\circ}$, $90^{\circ}$) for the shoulder angle of the lower die and the upper punch are suitably applied to this upper plate forming of the hollow-partitioned nozzle stator used for the turbine diaphragm.

• Transactions of Materials Processing
• /
• v.26 no.1
• /
• pp.11-17
• /
• 2017

In this study, process analysis of elbow-shaped tubes using a mandrel has been performed. To reach the final shape within the dimensional tolerance, the process analysis has been performed at various processing parameters such as tube dimensions, the curved cutting surface and the radius of curvature. The area outside the boundary of the target shape was expressed as a quantitative index to analyze the formability. The validation experiments have also been performed in order to increase the reliability of the process analysis. For the processing of elbow-shaped tubes, it is preferable to make the angle of the portion where the punch touches the tube smaller than the opposite angle. And the convex cutting surface is advantageous due to the increased contacts between the punch and the tube ends during the bending process. Elbow tube having larger radius of curvature shows higher dimensional accuracy due to the relatively uniform strain distribution.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1827-1836
• /
• 1997

In this paper, the clamping type forging of helical gears has been investigated. Clamping type forging is an operation in which the product is constrained to extrude sideways through an orifice in the container wall. Punch is cylindrical shaped. The punch compresses a cylindrical bilet placed in a die insetr. As a consequence the material flows in a direction perpendicular to that of punch movement. The forging has been analysed by using the upper-bound method. A kinematically admissible velocity field has been developed, wherein, an involute curve has been introduce to re4present tooth profile of the gear. Numerical calculations have been carried out to investigate the effects of various parameters, such as module, number of teeth, helix angle, friction factor and initial height of billet on the forging of helical gears. Some firgiing experiments were catrried out with aluminium alloy to show the validity of the analysis. Good agreement was found between the predicted values of the forging load and obtained from the experimental results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.349-355
• /
• 2017

Bending work using press dies involves bending a flat blank to a desired angle. The bending produces a flange (the bent part) and a web (the unbent part). The bending line will have a bending angle, and there is an inner and outer bending radius. The minimum inner radius size is determined by the material used. When the inner radius size is too small, there will be excess metal welding, which will cause a crack in the outer radius part. The outer bending radius size cannot be controlled by a bending punch and die block. Types of bending include V-bending, U-bending, O-bending, edge bending, twist bending, and crimping. Z-bending involves two bending lines, which are set on the upper side and under surface of the blank, respectively, and upward or downward bending is used. Z-bending is also called crank bending. Z-bending using this type of die structure will produce a standard inner bending radius. The standard size is the minimum bending radius that represents the angle radius of the bending punch. In industry, there is a need for a sharp edge shape with a very small size (R=0.2mm), but that is not possible when using bending punch and die block. The purpose of this research is to meet the need by development.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.3
• /
• pp.42-55
• /
• 1985

The study is concerned with the investigation of curved line folding of developable surface from flat sheets of metal. General geometric relations among folding line, folded surface, folded angle are derived. From the derived geometric relations, the required plastic work and punch force are derived for the first approximation. Five methods of forming are suggested and the experiment is carried out using two chosen methods for the prismatic developable surfaces of which cross-sections have 103.deg.arc, 180.deg.arc, sinusoidal shape. In the die design for the tolding of prismatic developable surfaces, a stack of sheets were used to form shapes of the dies by which acceptable folded surfaces were obtained. The computed plastic work and punch force turned out to be in reasonable agreement with the experimental result.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.3
• /
• pp.249-256
• /
• 1983

The study is concerned with the analysis of sheet metal for the prediction of limit drawing ratio and forming load. The direct redrawing process is analyzed by using an equilibrium approach and strain increment theory both for non-workhardening material and for workhardening material. Computations are carried out numerically for the workhardening case. Limit drawing ratios are predicted for some chosen variables. The forming loads are also computed with respect to punch travel. Then the predicted loads are compared with the experimental results. For ordinary lubricated conditions, the comparison shows reasonable agreement between the theory and experimental observation. It is also shown that limit drawing ration can be increased by using a greater die angle and proper lubrication significantly reduces the punch load. Finally numerical results show that material of greater R-value and strain-hardening exponent(n)is better for direst redrawing of sheet metal.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.283-288
• /
• 2012

Ultra-high-strength steels (UHSSs) are widely used for lightweight automobile parts, and the control of springback is very important in sheet-metal forming. The object of this study is to verify the effects of multi-stage forming process parameters for U-channel-type automobile parts made of UHSS. Finite element analysis is carried out to predict the formability and springback. The main parameters considered for the multi-stage forming process are the die angle, die radius, and punch-forming direction. It is shown that multi-stage forming is very effective for reducing springback, and that a small punch-forming angle and die radius reduce springback, whereas the die angle does not have a large effect.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.346-349
• /
• 2004

In the previous experimental study about extru-bending of angle product, the bending of extruded angle products with the '${\wedge}$' section and 'ㄱ' section can be abtained by the hot metal extru-bending machine with the two punches moving in the different velocity. The bending curvature can be controlled by the different velocity of billets through the two-hole container. This paper describes simulation of extru-bending process by the difference of punch velocities. The result of the forming simulation by $DEFORM^{TM}-3D$ shows that the bending phenomenon at the die exit during extrusion can be abtained by the two punches moving in the different velocity. And it is possible to design extrusion dies and to control the curvature of product through the simulation of extru-bending process by analysis

• Transactions of Materials Processing
• /
• v.32 no.2
• /
• pp.61-66
• /
• 2023

The quality of the sheared surface affects the stretch flangeability of steel sheet. The quality of sheared surface is influenced by several process factors such as die clearance, shape of cutting edge, use of counter punch, and shear. In this paper, the influence of these shearing process factors on the stretch flangeability of the HSS (DP980) was analyzed through a shearing and a stretch flangeability test. When the die clearance was 10%, the effect of these shearing process factors on the stretch flangeability was the greatest, and the use of an acute angle blade was found to be more advantageous in the stretch flangeability than a right angle blade. It was found that the stretch flangeability was improved when active bending was applied during shearing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1225-1226
• /
• 2013