• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.541-545
• /
• 2014

In this paper, the angle of the thighs that appear during walking condition to balance estimation to the left and right leg was occurred during normal walking. Get over to the limitations of gait analysis using image processing or foot pressure that was used a lot in the previous, the angle of the thigh were used for estimation of asymmetric gait. We implemented heathy five adult male to test targeting and gait and obtained cycle data from 10 times. For this research, Thigh-Angle measurement device were developed, and attached to in a position of $20^{\circ}$ for flexion and $15^{\circ}$ for extension to measure the angle of the thigh. Also, in order to verify the reliability of estimation of asymmetric gait using thigh-angle, it was compared with the result of asymmetric gait estimation using foot pressure. The results of this paper, using the thigh angle is the average of 16.84% higher than using pressure to accuracy of determine the gait imbalance.

• Journal of Mechanical Science and Technology
• /
• v.16 no.7
• /
• pp.873-881
• /
• 2002

In this paper, a on-line estimation method of the radial immersion angle using cutting force is presented. The ratio of cutting forces in feed and cross-feed directions acting on the single tooth at the immersion angle is a function of the immersion angle and the ratio of radial to tangential cutting force. It is found that the ratio of radial to tangential cutting force is not affected by cutting conditions and axial rake angle, which implies that the ratio determined by one preliminary experiment can be used regardless of the cutting conditions for a given tool and workpiece material. Using the measured cutting force during machining and predetermined ratio, the radial immersion ratio is estimated in process. Various experimental results show that the proposed method works within 5% error range.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.2
• /
• pp.79-88
• /
• 1998

We developed a method for the solid angle estimation of acetabular coverage of the femoral head in 3D space. The superior half of the femoral head is modeled as part of a sphere. And the tangent lines connecting from a set of points of the acetabular outline to the center of the fitted sphere are obtained. The lines passthrough the unit sphere whose center is the same as that of the femoral head. The interesecting points form a boundary on the unit sphere. With the points on the unit sphere, we calculate the covered area of the femoral headand estimate the solid angle. Solid angle is defined asthe suface area within the boundary on the unit sphere. In this measurements, the solid angle of normal subjects is on an average 4.3(rad) and the corresponding acetabular coverage is 68%. Unlinke the conventional methods, this solid angle estimation shows real 3D acetabular coverage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.6
• /
• pp.539-544
• /
• 2016

This paper improves Sherman's two-pulse method for angle estimation of two unresolved targets in phase comparison monopulse radar. The proposed method provides the angle information with only a single-pulse measurement instead of two pulses. The proposed method can estimate a single-target angle by single-target indicator, in contrast with previous techniques. The accuracy of angle estimation for proposed method is demonstrated by simulations.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1363-1370
• /
• 2018

In visible light (VL) positioning based on angle of arrival (AOA) estimation for smart indoor service, the AOA parameters obtained at the receiver has sometimes a random and distributed angle form instead of a point angle form due to the multipath transfer of the actual visible light and short positioning distance. The AOA estimation of a VL signal with a random and parametric distributed angle form may give incorrect AOA parameter estimates, which may result in poor VL positioning performance. In this paper, we classify the AOA parameters of the received VL signal into three forms according to the actual positioning channel environment and consider the short-range VL positioning method. We propose a subspace-based AOA parameter estimation technique and a data fusion method, and analyzed the proposed method by simulation and the measurement of the real VL channel characteristics.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.11
• /
• pp.966-972
• /
• 2013

Measurement or estimation of tilt angle is necessary for balancing robot such as Segway which is considered as a next generation transportation vehicle. However, it requires high-cost accurate sensors to hold balancing during stationary and moving situations. In this paper, a tilt angle estimation of a plane rotating in a vertical plane using low-cost sensors. Estimation using a set of 2-axis orthogonal accelerometers along with an inaccurate rate gyro has been considered. Feasibility and performance of the proposed technique has been verified through some experimental results.

• Journal of Advanced Navigation Technology
• /
• v.16 no.6
• /
• pp.952-959
• /
• 2012

In this paper, we propose an ESPRIT based algorithm for target position estimation with uniform linear array (ULA) and uniform circular array (UCA) at transmitter and receiver, respectively. When UCA is adopted at the receiver, unlike the case of ULA at the receiver, the rotational invariance of the received signal is satisfied. Although there has been an attempt to resolve this issue, the problem of direction of departure estimation has not been considered. In this paper, we provide an ESPRIT based algorithm to simultaneously estimate transmitter elevation angle, receiver elevation angle, and receiver azimuth angle, taking into account the transmitter antennas as well as the receiver antennas.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1463-1464
• /
• 2013

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.11C
• /
• pp.957-964
• /
• 2010

In this paper, we propose an indoor positioning algorithm based on 3 points near field angle-of-arrival estimation without side information. The conventional angle-of-arrival based positioning scheme requires the distance between the listener and the center of two points which is obtained by a received signal strength based range estimation. However, a received signal strength is affected by structure of room, placement of furniture, and characteristic of signal, these effects cause a large error to estimation of angle. In this paper, the proposed positioning scheme based on near field angle-of-arrival estimation can be used to estimate the position of listener without a prior distance information, just using time-difference-of-arrival information given from 3 points microphones. The performance of the proposed scheme is shown by cumulative distribution function of root mean squared error.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.153-155
• /
• 2004

This paper proposes a real-time approach on the rotational motion estimation and correction for the roll stabilization of the sight system. This method first estimates a rotation center by the least-mean square algorithm based on the motion vectors of some feature points. And, then, a rotation angle is searched for a best matching block between a reference block image and seccessive input images using MPC(maximum pixel count) matching criterion. Finally, motion correction is performed by the bilinear interpolation technique. Various computer simulations show that the estimation performance is good and the proposed algorithm is a real-time implementable one to the TMS320C6415(500MHz) DSP.