• Tribology and Lubricants
• /
• 제34권3호
• /
• pp.93-107
• /
• 2018

The purpose of Part I of this study is to find the potential region of wear scarring on engine journal bearings operating at a constant angular crank shaft velocity under firing conditions. To do this, we calculate the applied loads and eccentricities of a big-end journal bearing installed on a four-stroke and four-cylinder engine at every crank angle. Then, we find potential wear regions, such as a minimum oil film thickness, at every crank angle below most oil film thickness scarring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Thus, the wear region is defined as a set of each film thickness below the MOFTSW at every crank angle. In this region, the wear volume changes according to the wear depth and wear angle, depending on the minimum oil film thickness at every crank angle. The total wear volume is the summation during one cycle. Graphical views of the region in the two-dimensional coordinates show the crank angle and bearing angle along the journal center path, indicating the position of the minimum oil film thickness. The results of wear analysis show that the possible wear region is located at a few tens of angles behind the upper center of a big-end bearing at maximum power rpm.

• 건축역사연구
• /
• 제27권2호
• /
• pp.39-50
• /
• 2018

This study investigates the types and spread of framed structures of gable roofs meeting at right angle showed in old architecture and documentary paintings of houses, which were well liked in the early Joseon Dynasty. The conclusions of this study were as follows. First, the framed structure of gable roof meeting at right angle can be divided or recognized in 4 types according to their structure's size and purlin's position. Three of those types were noted to be in Seoul. Second, the framed structure of gable roofs meeting at right angle begun from the awareness of their independence from one another. Each space was divided based on their functions. Therefore, it could be extended in various forms, not only in the square plan physique but also in many different forms. And allowed free plan configuration regardless of column layouts or size of structure. Third, 5 purlins and 3 purlins crossing structure were preferred in Han-yang, the early Joseon Dynasty. It is related to the specific construction conditions of urban houses, such as the slope of land, limited land area, and economic power. Fourth, urban housing techniques were diffused throughout the country by officials who lived in Kae-gyeong and Han-yang at the end of Goryeo and early Joseon Dynasty. In other regions, framed structure of gable roof meeting at right angle households decreased, but in some regions of Gyeongsang-province, framed structure of gable roof meeting at right angle has maintained with Staggered purlin.

• 한국방사선학회논문지
• /
• 제12권1호
• /
• pp.39-46
• /
• 2018

본 연구는 영상의학과에 내원한 족부환자를 대상으로 족부 X선 검사 시 주상골(navicular)의 관찰이 어려운 점을 바탕으로 환자의 position과 X선관 각도의 변화를 주어 어떠한 position과 X선관 각도에서 주상골의 관찰이 용이한지를 알아보고자 하였다. 주상골 관찰을 위해 실험대상자의 position은 Foot AP, internal oblique, external Oblique position의 세 가지로 하였다. T-F angle(Tibia-Foot angle)은 $90^{\circ}$와 $135^{\circ}$로 정의하였고, X선관 각도는 $0^{\circ}$, $5^{\circ}$, $10^{\circ}$, $15^{\circ}$, $20^{\circ}$, $25^{\circ}$로 정의하여 실험한 후 획득한 영상을 비교 평가하였다. 실험결과, Foot AP position에서 T-F angle이 $90^{\circ}$인 경우 X선관 각도가 $15^{\circ}$일 때 설상골과 주상골의 겹침 정도는 3%이었고 블라인드 테스트 결과는 4.89점으로 골절의 판독 용이성이 가장 높았으며, T-F angle이 $135^{\circ}$경우에는 X선관 각도가 $15^{\circ}$일 때 설상골과 주상골의 겹침 정도는 5%이었고 블라인드 테스트 결과는 4.30점으로 판독 용이성이 가장 높았다. Foot internal oblique position에서는 T-F angle이 $90^{\circ}$인 경우 X선관 각도가 $0^{\circ}$일 때 설상골과 주상골의 겹침 정도는 4%이었고 블라인드 테스트 결과는 4.70점으로 가장 높았으며, T-F angle이 $135^{\circ}$경우에는 X선관 각도가 $0^{\circ}$일 때 그 겹침 정도는 5%이었고 블라인드 테스트 결과는 4.55점으로 가장 높게 나타났다. Foot external oblique position에서 T-F angle이 $90^{\circ}$인 경우 X선관 각도가 $15^{\circ}$일 때 설상골과 주상골의 겹침 정도는 4%이었고 블라인드 테스트 결과는 4.85점으로 가장 높았으며, T-F angle이 $135^{\circ}$경우에는 X선관 각도가 $15^{\circ}$일 때 그 겹침 정도는 5%이었고 블라인드 테스트 결과는 4.75점으로 가장 높게 나타났다. 결론적으로, 본 연구를 통하여 X 선 족부검사에서 각 position에 해당하는 주상골 관찰에 용이한 T-F 각도와 X선관 각도를 확인할 수 있었으며, 향후 본 연구 결과를 바탕으로 주상골 골절 판독에 유용한 참고자료가 될 수 있을 것으로 여겨진다.

• 한국운동역학회지
• /
• 제17권3호
• /
• pp.11-21
• /
• 2007

The purpose of this study was to examine the differences of kinematics and muscle activities depending on the changes of angle approaching balls during backhand drive in squash. The results are as follows. Stride time took the longest at AD2 and step lengths were the biggest at AD1 of left foot contact and right foot contact and AD2 of impact and follow-through. The center of gravity and the speed of racket head were the highest at AD3 and at AD2. Angle of shoulder joint were the biggest at AD1 of left foot contact, right foot contact and impact and AD3 of follow-through. Angle of elbow joint were the biggest at AD3 of left foot contact, right foot contact and follow-through and AD2 of impact. Angle of pelvis joint were the biggest at AD2 of left foot contact, AD1 of right foot contact and AD3 of impact and follow-through. Angle of knee joint were the biggest at AD2 of left foot contact, AD1 of right foot contact and AD3 of impact and follow-through. Angle of ankle joint were the biggest at AD1 of left foot contact and AD3 of right foot contact, impact and follow-through. According to the analysis results of triceps brachii, latissimus dorsi, brachioradialis muscle and flexor carpi ulnaris muscle activities were high at AD1 of all phases. Analysis results of vastus lateralis, vastus medialis, tibialis anterior and gastrocnemius medial muscle activities were high at AD2 of phase1 and phase3. Those of vastus lateralis, vastus medialis and tibialis anterior, gastrocnemius medial were high at AD3 of Phase 2 and AD1 of phase2.

• 한국안전학회지
• /
• 제20권2호
• /
• pp.18-25
• /
• 2005

This study performed finite element analysis on the pipe bend with various bend angles under loading conditions of internal pressure and combined pressure and bending, to investigate the effect of bend angle on the collapse behavior of pipe bend and on the stress state in the bend region. In the analysis, the pipe bends with bend angle of $5\~90^{\circ}$ were considered, and the bending moment was applied as in-plane closing and opening modes. From the results of analysis, it was found that the collapse moment of pipe bend increases with decreasing bend angle. As the bend angle decreases, also, the equivalent stress at intrados region increases regardless of bending mode. Under closing mode bending especially, the increase in stress at intrados is significant so that the maximum stress region moves from crown to intrados with decreasing bend angle.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.49-50
• /
• 2006

We have developed vertical alignment liquid crystal display (VA-LCD), of which the viewing angle can be controlled. The VA-LCD has the function of switching between the wide viewing mode and narrow viewing angle mode using one homogeneous aligned (HA) LC layer and one compensation film with a negative C-plate. The retardation of the HA layer at off axis can be controlled by applying an electric field while keeping the retardation value to be zero at normal direction. Consequently, the device exhibits a viewing mode over $170^{\circ}$ in terms of CR = 10 in wide viewing mode and about $60^{\circ}$ in terms of CR = 2 in narrow viewing angle mode m horizontal direction.

• 한국기계가공학회지
• /
• 제2권4호
• /
• pp.82-87
• /
• 2003

Flow angle with Swirl in a horizontal circular tube and a cylindrical annuli were experimentally studied for its visualization. This present investigation deals with flow angle, flow visualization studies and vortex core by using oil smoke and a hot wire anemometer for Re = 40,000 and 50000 at X/D = 41, 59 and 71 in a horizontal circular tube. In the swirl air flow, a vortex core was formed at high swirl intensity along the test tube. The flow angle and the vortex core depended on the swirl intensity along the test tube. The results of flow angles with swirl measured by flow visualization and hot wire reasonably agree with those of Sparrow One of the primary objectives of this research was to measure the flow angle with swirl in a cylindrical annuli along the test tube for different Reynolds numbers. The Reynolds number for these measurements ranged from 60,000 to 100,000 with L/D = a to 4.

• 한국운동역학회지
• /
• 제13권2호
• /
• pp.75-87
• /
• 2003

The purpose of this study was to identify the mechanical factors that are crucial to the successful double salto backward piked dismount on the parallel bars. The subjects were 5 national gymnasts(G1: sucessed landing, G2: failed landing), two video cameras were used to record the dismount of the subjects. It summarizes that (a) It is important to make small slope angle(X axis, Y axis) at release, whereas it makes large shoulder angle and trunk rotation angle. (b) It is important to prepare landing in advance, reducing vertical velocity and making large hip angle at BTO(body take off). (c) It is also important to make small knee angle and hip angle, and reduce the angle of trunk rotation.

• 한국가시화정보학회지
• /
• 제19권3호
• /
• pp.22-30
• /
• 2021

Ventilated cavity shapes by varying angle of attack of a circular cavitator were predicted based on Logvinovich's Independence Principle in order to verify the cavity shape prediction method. The prediction results were compared with model experiments conducted in the high-speed cavitation tunnel. In the prediction of the cavity centerline, the movement of the cavity centerline due to the effect of gravity and cavitator's angle of attack were well predicted. In the prediction of the cavity contour, it was found that the cavity edge prediction error increased as the angle of attack increased. The error of the upper cavity contour was small at the positive angle of attack, and the error of the lower cavity contour was small at the negative angle of attack.

• 한국운동역학회지
• /
• 제33권2호
• /
• pp.73-83
• /
• 2023

Objective: Adolescent idiopathic scoliosis patients make up 40% of all scoliosis patients, and it is likely to increase even more because of the increase in sitting times due to the pandemic. Method: The subject of this study was a 16-year-old female student. The Cobb's Angle at initial value was 42° at the thoracic and 33° at the lumbar. The subject's height was 161.6 cm, and the type of scoliosis was 3CL. The brace was built with fabric materials with the size information from the X-ray information and actual measurements. The brace was made for the adolescents to wear for a longer time by making them put pressure on the same pressure points of the existing braces. The subjects were required to wear the device for 16 hours every day for three months. Additional features to check the pressure and time were synchronized through an app for easier communication and management with the responsible investigator. Results: After wearing the 3D Fabric brace, Cobb's angle changed from 42° to 33° at the thoracic and 33° to 23° at the lumbar. The ATR changed from 9° to 8° at the thoracic and 11° to 6° at the lumbar. As a result, the changes in the ATR angle do relate to the decrease of Cobb's angle, which made the angle of scoliosis that is bent in a three-dimensional way improve, making the height of the subject increase from 161.6 cm to 163.5 cm. Conclusion: Through this study, developing a brace that is made in the form of the 3CL to align the strap direction and putting pressure on the proper pressure points makes Cobb's angle and the ATR smaller. This means that there is a positive effect on the changes in height. A brace made of light fabric material is a good brace to help treat adolescent idiopathic scoliosis. There was an opinion that it is more comfortable to wear than existing braces, but it seems necessary to conduct a quantitative study about the before and after of wearing the brace and a survey for Korean specific cases.