• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.422-427
• /
• 2000

The design of low-solidity vaned diffusers and the effect on the performance of a turbocharger compressor is discussed. The effect of vane number and turning angle was investigated while maintaining a basic design with a leading edge angle of $70^{\circ}$, leading and trailing edge radius ratios of 1.1 and 1.3. All results are compared with those obtained with the standard vaneless diffuser configuration and it was shown that all designs increased and shifted the pressure ratio to reduced flowrates. Despite the low-solidity configuration none of the vane designs provided a broad operating range, and the vane leading edge angle was not main factor that system went into the surge condition. The diffuser of higher trailing edge angle improved the flow range for the compressor to operate at lower flow region.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.497-501
• /
• 2009

Effect of angle of supply air on cooling and heating performances of office space is studied by numerical simulation. For a constant air volume(CAV) air-conditioning system, air is supplied vertically($90^{\circ}$) and horizontally($10^{\circ}$). Due to buoyancy, the supply angle affects the performance of cooling and heating. In cooling, since the cold supply air tends to move downward due to its high density, horizontal supply angle is better for uniform temperature distribution. In heating, however, vertical supply angle is preferred for better mean and uniform temperature distribution.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.14-21
• /
• 2010

In this study, presintered low purity alumina ceramics were machined with various tools to clarify the effects of the tool material, cutting condition and tool geometry on machinability. The main conclusions obtained were as follows. (a)The wear of tungsten carbide tool becomes smaller with the increase of the feed and clearance angle, and with the decrease of rake angle, especially exhibiting considerably smaller wear with both the decrease of rake angle and the increase of clearance angle. (b) So far as turning the ceramic presintered at low temperature, the diamond tool shows the best performance with higher feed. (c) The effect on the tool wear of the feed, clearance angle and rake angle becomes smaller in turning the ceramic presintered at higher temperature. (d) The tool wear is not severely affected by the depth of cut.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.12-18
• /
• 2001

The objective of the present work is to examine the effect of inclined angle of channel with multi heat source on thermal stability of electronic equipment. The heat sources are mounted on both sides of channel walls by two kinds of configuration such as the zig-zag md symmetric on. Conductive heat transfer was estimated by using of thermocouples and heat flux sensor. Thus, convective heat transfer and mean Nusselt number could be obtained. With increased inclined angle, the convective heat transfer coefficient was decreased. When inclined angle was smaller than 30 degree, The average Nusselt number of Big-zag configuration was larger than that of symmetric. Furthermore, when protruding ration was 0.082, the temperature was strongly affected by inclined angle. whereas, when protruding ration was 0.25, the temperature was strongly affected by heat source configuration.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.3
• /
• pp.145-148
• /
• 2006

In this study, the response surface modeling of the pretilt angle control using in-situ photoalignment method with oblique UV exposure .on plastic substrate is investigated. The pretilt angle is the main factor to determine the alignment of the liquid crystal display. The response surface model is used to analyze the variation of the pretilt angle on the various process conditions. Heating temperature and UV exposure time are considered as input factors. The liquid crystal (LC) pretilt angle increased with increasing heating temperature and UV exposure time. The analysis of variance is used to analyze the statistical significance and the effect plots are also investigated to examine the relationship between the process parameters and the response.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.15 no.4 s.40
• /
• pp.437-445
• /
• 1991

The effect of diameter of rods or fibers on contact angle was studied in a vertical rod configuration. A contact angle measuring device described in the previous paper was optimized for the measurement of small-diameter fibers. It was shown that contact angles of water and hexadecane on nylon 6 monofilsments and glass rods increased with decrease of diameter below a critical diameter, which varied from one system to another. Beyond the critical value, contact angle of the liquid on the vertical glass rod reached to an equilibrium value which is equal to the unique value of the contact angle of the liquid drop on the horizontal glass plate.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.34 no.1
• /
• pp.78-86
• /
• 1992

This paper aims at investigating the effect of steel ratio and the magnitude of edge-ratio on the mechanical characteristics of reinforced concrete ring sector plate. The influence of steel bars was taken into account by coupling stiffness matrix of the steel bar element with that of the concrete plate element without dealing with separate element of steel bar and by establishing the composite stiffness matrix, which leads to the desirable result which does not increase th number of element could be obtained. Through case studies with 6 cases various steel ratios in ring sector plate supported at four edges and 4 cases with different open angles, the influence of the steel ratio was examined. A numerical analysis to find out the effect of the steel ratio d ue to above mentioned cases was carried out by 4 boundary conditions ; all edges clamped (B.C-1), all edges simply supported (B.C-2), curvilinear two edges clamped and other edges free (B.C-3) and curvilinear two edges simply supported and other edges free(B.C-4). The main results obtained are summarized as follows : 1. The effect of steel ratio on the magnitude of lateral deflection and x-directional bending moment at the center of sector plate and the midpoint of outer and inner curvilinear edges is almost the same up to $30^{\circ}$ of open angle. Beyond $30^{\circ}$ of the angle, the larger the angle, the greater the effect of ratio. 2. In design works using balanced steel ratio, the effect of steel bar can be ignored. But for larger open angles, especially greater than $90^{\circ}$, it proves desirable to consider the effect of steel bar. 3. The effect of the arc length of center circle/straight edge on lateral deflection and bending moment is remarkable in B.C-2. For larger open angle, the effect is also noted except for B.C-3 which turn out hardly affected. 4. The effect of the radius of curvature/straight side length on lateral deflection and x-directional bending moment is noted in B.C-2. As open angle increases, B.C-1 and B.C-3 almost agree and B.C-2 approaches B.C-4.

• Journal of the Korean Society of Physical Medicine
• /
• v.9 no.4
• /
• pp.339-345
• /
• 2014

PURPOSE: This study is to investigate the effect of 4 weeks of gym ball exercise on the pelvis and spine of women in 20s. METHODS: Randomly selected 10 of 20 subjects are allocated to experimental group who will practice gym-ball exercise while the rest 10 subjects are allocated to control group. Values for pelvic obliquity DL-DR, pelvic torsion DL-DR, pelvic rotation, kyphotic angle ICT-ITL (max), and lordotic angle ITL-ILS (max) were measured through recording using 3-dimensional image analyzer as a preliminary inspection. Gym-ball exercise was implemented 3 sessions a week for 4 weeks. Each session consisted of 10 minutes of warm up exercise, 30 minutes of main exercise, and 10 minutes of cool down exercise totaling 50 minutes. Post inspections were measured after exercise. RESULTS: Experimental group showed statistically significant difference in pelvic obliquity DL-DR, pelvic torsion DL-DR, and kyphotic angle ICT-ITL (max) (p<.05) and values of pelvic obliquity DL-DR showed statistically significant difference between two groups (p<.05). However pelvic rotation, lordotic angle ITL-ILS (max) did not show a significant difference. CONCLUSION: These results showed that gym-ball exercise has positive effect in the pelvic obliquity, torsion and spine kyphotic angle and expected to have positive effect on the body balance, body lineup, and coordination.

• The Journal of Korean Physical Therapy
• /
• v.17 no.4
• /
• pp.559-567
• /
• 2005

The purpose of this research is to study how the stretching exercise along with heat and electric therapy can effect on Angle of Lumbar Flexion and Reduction of Pain against the Hamstring Construction Symptom that can be found in the Chronic Low Back Patients. The target of research was 28 person selected out of the patients diagnosed as Lumbar Sprain and Lumbar Syndrome, who have positive from the active test of Hamstring construction and passive test. Their age range is 20 to 60 years old, 14 male and 14 female. As a research method, simple heat and electric therapy was applied to counter part while Hamstring Stretching Exercise including simple heat and electric therapy was applied to the experimental part. After 6 weeks treatment for each part, the results of effect on Angle of Lumbar Flexion and Pain Reduction was compared and analysed on the basis of the gravity angle meter and Visual Analogue Scale (VAS). The outcome of research is as follows: 1. Angle of Lumbar Flextion increased effectively not in the conventional counter group but the experimental group to which Hamstring Stretching was applied simultaneously. 2. remarkable effect was shown in the experimental part applied Hamstring Stretching. Consequently from the results of this study, we could find out the fact that the therapy combined preserve treatment and hamstring stretching not only produced increasing Lumbar Flexion Angle but also was more effective on reducing pain of the patients according to it than the conventional or preserve therapy.

• Journal of Korean Physical Therapy Science
• /
• v.12 no.4
• /
• pp.57-67
• /
• 2005

The purpose of this study is to investigate the effect of low back pain(LBP) and pelvic displacement on foot orthosis. Before and after experiments were designed to compare the effect. 21 LBP patients who were the subjects diagnosed of applying foot orthosis for 3 weeks after, investigated about pelvic obliquity angle, displacement of ilium, lumbo-sacral angle by x-ray test which is one of pelvic displacement tests, visual analogue scale is used for LBP measurement. The result show the followings; First, Pelvic obliquity angle was significantly reduced after applying foot orthosis compared before using it(p<.05). Second, Displacement of ilium was significantly reduced after applying foot orthosis compared before using it(p<.05). Third, Lumbo-sacral angle was significantly reduced after applying foot orthosis compared before using it(p<.05). Fourth, LBP was significantly reduced after applying foot orthosis compared before using it(p<.05). This study tries to suggest new LBP treatment to reduce pelvic displacement by apply foot orthosis. In conclusion, foot orthosis reduces pelvic obliquity angle, displacement of ilium, lumbo-sacral angle and also decrease LBP. Further more, It needs of biomechanical study which can recognize relation between foot arch and pelvic displacement. This study will serve as a clinically useful data for diagnosis and treatment of LBP and biomechanical analysis of lower limb.