• 한국산업정보학회:학술대회논문집
• /
• 한국산업정보학회 1997년도 추계학술대회 발표논문집:21세기를 향한 정보통신 기술의 전망
• /
• pp.451-462
• /
• 1997

A 2-dimensional numerical analysis is presented for thermal-electron heat conduction effects upon the electron transport and the drain current-voltage characteristics of submicron GaAs MESFETs, based on the use of a nonstationary hydrodynamic transport model. It is shown that for submicron GaAs MESFETs, electron heat conduction effects are significant on their internal electronic properties and also drain current-voltage characteristics. Due to electron heat conduction effects, the electron energy is greatly one-djmensionalized over the entire device region. Also, the drain current decreases continuously with increasing thermal conductivity in the saturation region of large drain voltages above 1 V. However, the opposite trend is observed in the linear region of small drain voltages below 1 V. Accordingly, for a large thermal conductivity, negative differential resistance drain current characteristics are observed with a pronounced peak of current at the drain voltage of 1 V. On the contrary, for zero thermal conductivity, a Gunn oscillation characteristic is observed at drain voltages above 2 V under a zero gate bias condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.980-984
• /
• 2002

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verified the test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirm approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design.

• 대한기계학회논문집A
• /
• 제35권12호
• /
• pp.1627-1633
• /
• 2011

사출금형은 일반적으로 다수개의 부품을 조립하여 제작되며, 특히 성형부(Core/Cavity)가 금형 형판 내부에 조립되는 구조를 갖는다. 이러한 구조로 인해 금형 조립부 경계면에서는 열접촉 저항이 발생하여 금형 내부의 열전달 특성에 영향을 미치게 된다. 최근 금형의 열접촉 저항이 성형부의 온도분포에 미치는 영향을 수치적으로 예측하기 위한 선행연구가 수행되었으며, 본 연구에서는 이에 기반하여 열-유동 연계해석을 적용함으로써 금형 내부의 열접촉 저항이 사출성형시 유동특성에 미치는 영향을 분석 하였다. 상기 해석결과와 실험결과와의 비교분석을 통해 금형의 열접촉 저항을 고려한 열-유동 연계해석이 기존의 해석방법과 비교할 때 사출성형 유동특성을 보다 향상된 신뢰성으로 예측할 수 있음을 확인하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.285-290
• /
• 2000

Unsteady-state temperature distributions and thermal deformations in high speed spindle are studied. For the analysis, three dimensional model is built considering heat transfer characteristics such as natural and forced convection coefficients Temperature distributions and thermal deformations are analyzed by using the finite element method. Results of analysis are compared with the measured data.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권1호
• /
• pp.46-55
• /
• 2004

Thermal characteristics of the various cooling methods in electronic equipment are studied numerically. A common chip cooling system is modeled as a parallel channel with protruding heat sources. A two-dimensional model has been developed for the numerical analysis of compressible. viscous. laminar flow. and conjugate heat transfer between parallel plates with uniform block heat sources. The finite volume method is used to solve this problem. The assembly consists of two channels formed by two covers and one printed circuit board that is assumed to have three uniform heat source blocks. Various cooling methods are considered to find out the efficient cooling method in a given geometry and heat sources. The velocity and the temperature fields. the local temperature distribution along the surface of blocks. and the maximum temperature in each block are obtained. The results are compared to examine the thermal characteristics of the different cooling methods both quantitatively and qualitatively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.792-793
• /
• 2011

The purpose of this paper is to study the thermal and mechanical characteristics of HTS (high temperature superconductor) field magnet according to the design of a small size superconducting rotor without insulation. First, basic design data of superconducting rotor were acquired through electromagnetic analysis. Based on these data, analysis regarding mechanical and thermal characteristics of HTS field magnet was executed. Anisotropic condition was considered in the mechanical characteristics of HTS field magnet. Average values of specific heat and heat conductivity up to 30 K were used during the analysis of thermal characteristics. Analysis results show superior mechanical and thermal characteristics of insulationless HTS field magnet compared with insulated HTS field magnet.

• KEPCO Journal on Electric Power and Energy
• /
• 제2권2호
• /
• pp.273-278
• /
• 2016

In order to evaluate the lifespan of high-temperature parts with thermal barrier coating in gas turbines used for power generation, this study was performed on an 80 MW-class gas turbine exceeding 24 k equivalent operating hours. Degradation characteristics were evaluated by analyzing the YSZ (Yttria Stabilized Zirconia) top coat, which serves as the thermal barrier coating layer, the NiCrAlY bond coat, and interface layers. Microstructural analysis of the top, middle, and bottom sections showed that Thermal Growth Oxide (TGO) growth, Cr precipitate growth within the bond coat layer, and formation of diffusion layer occur actively in high-temperature sections. These microstructural changes were consistent with damaged areas of the thermal barrier coating layer observed at the surface of the used blade. The distribution of Cr precipitates within the bond coat layer, in addition to the thickness of TGO, is regarded as a key indicator in the evaluation of degradation characteristics.

• 한국정밀공학회지
• /
• 제26권7호
• /
• pp.120-126
• /
• 2009

Thermal displacement of high speed spindle is very important problem to be solved. To solve heat generation and thermal displacement problems that influence on the product accuracy, it is very important to predict thermal characteristics of the spindle and it is positively necessary to select the conditions of cooling, flow rate and preload of bearings. In this paper, 30,000rpm($1.455{\times}10^6DmN$) spindle was designed and produced. The analysis of thermal deformation for heat generation of inner spindle was carried out using commercial program $ANSYS^{(R)}$ and the result was compared with measured data using $LabVIEW^{(R)}$ and SGXI-1600, 1125 and 1126 module. Temperature distribution and thermal displacement according to spindle speed are measured. Using this method, it is possible to predict and to improve thermal characteristic of high speed spindle by control spindle speed, bearing preload and cooling rate.

• 한국의류산업학회지
• /
• 제20권6호
• /
• pp.744-751
• /
• 2018

This study aimed to provide the information on the thermal sensation and the amount of clothing worn of junior high school students in winter classroom the relation with their climate adaptability. Total usable questionnaires were obtained from 467 male and female students. The questionnaire included general characteristics, physical characteristics, self awareness of body shape, climate adaptability and subjective thermal sensation in winter classroom. The data were analyzed using SPSS Statistics 18.0 for frequency analysis, factor analysis, chi-square analysis, t-test and correlation analysis. The results were as follows. The average body type based on BMI was normal($20.1kg/m^2$ ). Females perceived their body type as thinner than males. They wore more (8.67 garment items compared to 8.14 for males). Only about 25% of students voted the thermal sensation to neutral(47% cool~very cold, 28% warm~very hot). Females were more sensitive to the cold, perceived less healthy, and wore more garments in the cold. Students felt colder in winter classroom when their cold adaptability was lower and they actively adjusted thermal insulation against the cold. It is recommended to suggest the guidelines for the proper indoor temperature and for the wear behavior in classroom in the perspectives of increasing the learning efficiency and improving the students' climate adaptability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.1021-1026
• /
• 2000

The thermal characteristics of high-speed air spindle system with built-in motor are studied. Experiment and finite element method analysis obtain temperature rise and temperature distribution of housing. For the analysis three-dimensional model is built and temperature rise and distribution in thermal steady state are computed for each rotational frequency. Generally. It is said that the heat generation of air bearing is negligible. But it is certain that the heat generation of air bearing can not be negligible especially in high-speed conditions Frequency response test for air spindle system is executed. In case that the heat generation of air spindle system is high, natural frequency of the system becomes lower when it reaches thermal steady-state and it means that the stiffness of air hearing becomes smaller due to the change of bearing clearance. It is shown that the temperature rise of all spindle system causes thermal expansion md induces the variation of hearing clearance. In consequence the st illness of air bearing becomes smaller.