• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.175-182
• /
• 2015

Objective : The purpose of this study was to investigate difference in fascicle behavior of the medial gastrocnemius during the locomotion with varying intensities, such as gait and one-legged and two-legged vertical jumping. Methods : Six subjects (3 males and 3 females; age: $27.2{\pm}1.6yrs.$, body mass: $62.8{\pm}9.8kg$, height: $169.6{\pm}8.5cm$) performed normal gait (G) at preferred speed and maximum vertical jumping with one (OJ) and two (TJ) legs. While subjects were performing the given tasks, the hip, knee and ankle joint motion and ground reaction force was monitored using a 8-infrared camera motion analysis system with two forceplates. Simultaneously, electromyography of the triceps surae muscles, and the fascicle length of the medial gastrocnemius were recorded using a real-time ultrasound imaging machine. Results : Comparing to gait, the kinematic and kinetic parameters of TJ and OJ were found to be significantly different. Along with those parameters, change in the medial gastrocnemius (MG) muscle-tendon complex (MTC) length ($50.57{\pm}6.20mm$ for TJ and $44.14{\pm}5.39mm$ for OJ) and changes in the fascicle length of the MG ($18.97{\pm}3.58mm$ for TJ and $20.31{\pm}4.59mm$ for OJ) were observed. Although the total excursion of the MTC and the MG fascicle length during the two types of jump were not significantly different, however the pattern of length changes were found to be different. For TJ, the fascicle length maintained isometric longer during the propulsive phase than OJ. Conclusion : One-legged and two-legged vertical jumping use different muscle-tendon interaction strategies.

• Physical Therapy Korea
• /
• v.19 no.1
• /
• pp.1-9
• /
• 2012

The purpose of this study was to investigate the kinematic and kinetic changes that may occur in the pelvic and spine regions during cross-legged sitting postures. Experiments were performed on sixteen healthy subjects. Data were collected while the subject sat in 4 different sitting postures for 5 seconds: uncrossed sitting with both feet on the floor (Posture A), sitting while placing his right knee on the left knee (Posture B), sitting by placing right ankle on left knee (Posture C), and sitting by placing right ankle over the left ankle (Posture D). The order of the sitting posture was random. The sagittal plane angles (pelvic tilt, lumbar A-P curve, thoracic A-P curve) and the frontal plane angles (pelvic obliquity, lumber lateral curves, thoracic lateral curves) were obtained using VICON system with 6 cameras and analyzed with Nexus software. The pressure on each buttock was measured using Tekscan. Repeated one-way analysis of variance (ANOVA) was used to compare the angle and pressure across the four postures. The Bonferroni's post hoc test was used to determine the differences between upright trunk sitting and cross-legged postures. In sagittal plane, cross-legged sitting postures showed significantly greater kyphotic curves in lumbar and thoracic spine when compared uncrossed sitting posture. Also, pelvic posterior tilting was greater in cross-legged postures. In frontal plane, only height of the right pelvic was significantly higher in Posture B than in Posture A. Finally, in Posture B, the pressure on the right buttock area was greater than Posture A and, in Posture C, the pressure on the left buttock area was greater than Posture A. However, all dependent variables in both planes did not demonstrate any significant difference among the three cross-legged postures (p>.05). The findings suggest that asymmetric changes in the pelvic and spine region secondary to the prolonged cross-legged sitting postures may cause lower back pain and deformities in the spine structures.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.117-132
• /
• 2005

It was to study a following research of "A Kinematic Analysis of Air-rolling-breakfall in Judo". The purpose of this study was to analyze the Center of Gravity(COG) variables when performing Air-rolling-breakfall motion, while passing forward over(PFO) to the vertical-hurdles(2m height, take off board 1m height) in judo. Subjects were four males of Y. University squad, who were trainees of the demonstration exhibition team, representatives of national level judoists and were filmed by four 5-VHS 16mm video cameras(60field/sec.) through the three dimensional film analysis methods.COG variable were anterior-posterior directional COG and linear velocity of COG, vertical directional COG and linear velocity of COG. The data collections of this study were digitized by KWON3D program computed The data were standardized using cubic spline interpolation based by calculating the mean values and the standard deviation calculated for each variables. When performing the Air-rolling-breakfall, from the data analysis and discussions, the conclusions were as follows : 1. Anterior-posterior directional COG(APD-COG) when performing Air-rolling-breakfall motion, while PFO over to the vertical-hurdles(2m height) in judo. The range of APD-COG by forward was $0.31{\sim}0.41m$ in take-off position(event 1), $1.20{\sim}1.33m$ in the air-top position(event 2), $2.12{\sim}2.30m$ in the touch-down position(event 3), gradually and $2.14{\sim}2.32m$ in safety breakfall position(event 4), respectively. 2 The linear velocity of APD-COG was $1.03{\sim}2.14m/sec$. in take-off position(event 1), $1.97{\sim}2.22m/sec$. gradually in the air-top position(event 2), $1.05{\sim}1.32m/sec$. in the touch-down position (event 3), gradual decrease and $0.91{\sim}1.23m/sec$. in the safety breakfall position(event 4), respectively. 3. The vertical directional COG(VD-COG) when performing Air-rolling-breakfall motion, while PFO to the vertical-hurdles(2m height) in judo. The range of VD-COG toward upward from mat was $1.35{\sim}1.46m$ in take-off position(event 1), the highest $2.07{\sim}2.23m$ in the air-top position(event 2), and after rapid decrease $0.3{\sim}0.58m$ in the touch-down position(event 3), gradual decrease $0.22{\sim}0.50m$ in safety breakfall position(event 4), respectively. 4. The linear velocity of VlJ.COG was $1.60{\sim}1.87m/sec$. in take-off position(event 1), $0.03{\sim}0.08m/sec$. gradually in the air-top position(event 2), $-4.37{\sim}\;-4.76m/sec$. gradual decrease in the touch-down position(event 3), gradual decrease and -4.40${\sim}\;-4.77m/sec$. in safety breakfall position(event 4), respectively. When performing Air-rolling-breakfall showed parabolic movement from take-off position to air-top position, and after showed vertical fall movement from air-top position to safety breakfall. In conclusion, Ukemi(breakfall) is safety fall method Therefore, actions need for performing safety fall movement, that decrease and minimize shock and impact during Air-rolling-breakfall from take-off board action to air-top position must be maximize of angular momentum, and after must be minimize in touch-down position and safety breakfall position.

• The Journal of Korean society of community based occupational therapy
• /
• v.4 no.1
• /
• pp.23-31
• /
• 2014

Objective : The objectives of this study were to compare the variables from Fitmeter accelerometer with them from CMS-70P(Zebris Medizintechnik Gmbh, Germany) and to suggest the availability the accelerometer in the field of occupational therapy. Methods : Twenty participants performed calling, drinking water, washing face and spooning and we measured Sum of Single Vector Magnitude(SSVM) and range of motion(ROM) on the wrist and elbow joints. Results :With respect to the wrist and elbow joints, SSVM and ROM differed significantly according to the task(calling, drinking water, washing face and spooning)(p<.001; p<.001; p<.001; p<.001). As for the wrist joint, SSVM and ROM did not show the significant correlation(p>.05) but as for the elbow joint, SSVM and ROM did show the significant correlation according to the task(p<.01; p<.001; p<.01; p<.05). With regard to the SVM-difference of wrist and elbow joints, calling and washing showed the significant difference (p<.001; p<.05) but drinking and spooning did not show the significant difference(p>.05; p>.05). Conclusion : We suggest that Fitmeter accelerometer would be use to record the kinematic variables during performance of ADL and it can compensate the function of CMS-70P as for the elbow joint than the wrist joint.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.3
• /
• pp.39-46
• /
• 2014

Network RTK positioning, one of GNSS positioning systems, is currently very popular due to its easy operation and low cost. However, the network RTK positioning unquestioningly accepts observation result acquired with an ambiguity fixed-solution regardless of different field conditions and situations, and then it is applied to the practice. This paper, therefore, has investigated the effects of field conditions obtained network RTK survey data for the area with obstacles on the variation of positioning accuracy. Being explained in detail, after conducting survey by GPS-only positioning and combined GPS/GLONASS observations giving changes to the distance from obstacles and elevation angles, and then accuracy results of each positioning method were compared each other. As a result, while GPS-only point positioning method showed more stable results than combined GPS/GLONASS method in the areas with no obstacles, combined method gave better result than GPS-only for the areas with presence of obstacles. Based on the results of this experiment, when the further study is conducted with a variety of different field conditions affecting the survey accuracy, it can be expected that the accuracy of network RTK survey method would become to more popular.

• Journal of Korea Water Resources Association
• /
• v.43 no.8
• /
• pp.747-755
• /
• 2010

Distributed Models have relative weak points due to the amount of computer memory and calculation time required for calculating water flow using a numerical analysis based on kinematic wave theory when compared to the conceptual models used so far. Typically, the distributed models have been mainly applied to small basins. It was necessary to decrease the resolution of the grid to make it applicable for large scale watersheds, and because it would take up too much time to calculate using a higher resolution. That has been one of the more difficult factors in applying the model for actual work. In this paper, MPI (Message Passing Interface) technique was applied to solve the problem of calculation time as it is one of the demerits of the distributed model for performing physical and complicated numerical calculations for large scale watersheds. The comparison studies were performed a single domain and a divided small domain in Yongdam Dam watershed in case of typoon 'Ewiniar' at 2006. They were compared to analyze the application effects of parallelization technique. As a result, a maximum of 10 times the amount of calculation time was saved but keeping the level of quality for discharge by using parallelization code rather than a single processor.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.6
• /
• pp.457-467
• /
• 2018

Currently, the regulation and rules for public surveying and the UCPs (Unified Control Points) adapts those of the triangulated traverse surveying. In addition, such regulations do not take account of the unique characteristics of GNSS (Global Navigation Satellite System) surveying, thus there are difficulties in field work and data processing afterwards. A detailed procesure of GNSS processing has not yet been described either, and the verification of accuracy does not follow the generic standards. In order to propose an appropriate procedure for field surveys, we processed a short session (30 minutes) based on the scenarios similar to actual situations. The reference network in Seoul was used to process the same data span for 3 days. The temporal variation during the day was evaluated as well. We analyzed the accuracy of the estimated coordinates depending on the parameterization of tropospheric delay, which was compared with the 24-hr static processing results. Estimating the tropospheric delay is advantageous for the accuracy and stability of the coordinates, resulting in about 5 mm and 10 mm of RMSE (Root Mean Squared Error) for horizontal and vertical components, respectively. Based on the test results, we propose a procedure to estimate the daily solution and then combine them to estimate the final solution by applying the minimum constraints (no-net-translation condition). It is necessary to develop a web-based processing system using a high-end softwares. Additionally, it is also required to standardize the ID of the public control points and the UCPs for the automatic GNSS processing.

• The Journal of the Petrological Society of Korea
• /
• v.27 no.3
• /
• pp.173-184
• /
• 2018

Geologic structures related to the latest event in the evolution around Gyeongsang Basin are mainly associated with the Yangsan Fault. In particular, the structures in the northern part of the Yangsan Fault are mainly observed in the region between Bogyeongsa Temple and Danguri. Such structures are also clustered in the vicinity of the Yangsan Fault, exhibiting similar geometric and kinematic patterns. In general, N-S and NE-SW trending fractures and tectonogeomorphic lineament are mainly eastward dipping reverse faults, such that the blocks in the east of the structures moved west or northwest. The reverse faults are segmented by NW trending fractures that accommodate strike-slip movements. The reverse faults and geomorphotectonic lineaments related to the latest event of deformation in the northern part of the Yangsan Fault show a westward convex patterns. We infer that these structures were initially normal faults that formed during a NW-SE extensional environment and were later reactivated during an E-W compressional one. Such a deformation pattern is also well developed around Pohang-Heunghae area based on the tectonogeomorphic analysis, which appears to be closely related to the Pohang Earthquake (15 Nov. 2017), and its development of the surface rupture and highly damaged zones.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.77-85
• /
• 2009

This study is aimed at providing information on injury prevention and skill improvement by inducing the accurate movements in exercise as well as understanding the principles of badminton drive movements. Movement displacement of racket head showed the similar patterns among those surveyed but, it seemed that slight differences resulted from external factors such as height, length of brachial and forearm and individual trend of swing locus. Regarding upper joint angle per phase, the angles of shoulder joint, elbow joint and wrist joint were closely associated in taking drive movements and they supported the segment order theory that power was conveyed from proximal into distal. It was shown that angular velocity of upper joint became larger in follow through movement after impact among all those surveyed, which meant the importance of follow through in racket sports such as badminton. In conclusion, this follow through movement acts as an important factor in racket sports in terms of pose stability maintenance, pose correction of movements and injury prevention of joints. In summary, when swings are made according to segment order theory, efficient movements can be taken.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.21-30
• /
• 2005

The purpose of this study is helps to make full use for perfect performance by grasping the defects of Tichonkich motion performed by athlete CSM For this, the study analyzed kinematical variables through Tichonkich motions performed at the first selection competition(1st trial) and final selection competition(2nd trial) for the dispatch to the 28th Athens Olympic Games using the three-dimensional cinematographical method with a high-speed video camera, and obtained the following results. 1. During Tichonkich motion, the execution time of up swing and the right hand moving to the left bar was shorter in the 2nd trial than the 1st one, while the execution time of down swing, the support of the left bar and the right hand moving to the right bar was longer in the 2nd trial than the 1st trial. 2. The horizontal position of COG in the 2nd trial was -35cm in the 1st stage, 42cm in the 3rd stage and 29cm in the 4th stage, that is, it showed a great swing focused on the circular movement compared to the 1st trial, while the vertical position of COG was -59cm in the 2nd stage, that is, it showed a small swing focused on a up and down movement. Also the 5th stage vertical position was 98cm, and the 6th stage vertical position was 95cm in the 2nd trial which were higher than those of the 1st trial, so it has provided magnificence required in the modern gymnastics. 3. And it was indicated that the horizontal velocity at the down swing phase proceeded forward more rapidly in the 2nd trial than that in the 1st trial, and the reverse ascent made a rapid vertical rise lessening left and right velocity change. And in the 5th stage, the 2nd trial was kept very slower in horizontal, vertical and left and right velocity that in the 1st trial, so it reached a handstand with leisurely movement. 4. In the 2nd trial, shoulder joint of the 1st, 2nd, 3rd stages kept a larger angle than that in the 1st trial, that is, it made a great swing while in the 1st trial, it showed a swing movement dependent on kick movement by the flexion and extension of hip joint. Also in the 2nd trial, the body formed a vertical posture with both hands supporting the left bar and hip joint was kept larger as $198^{\circ}$ and $190^{\circ}$ in the 5th and 6th stage than that in the 1st trial, so it made a handstand with the body uprightly stretched out, and magnificent and stable movement.