• Smart Structures and Systems
• /
• 제2권2호
• /
• pp.115-126
• /
• 2006

The Terra-Scope system is an affordable 4-D down-hole seismic monitoring system based on independent, microprocessor-controlled sensor Pods. The Pods are nominally 50 mm in diameter, and about 120 mm long. They are expected to cost approximately $6000 each. An internal 16-bit, extremely low power MCU controls all aspects of instrumentation, eight programmable gain amplifiers, and local signal storage. Each Pod measures 3-D acceleration, tilt, azimuth, temperature, and other parametric variables such as pore water pressure and pH. Each Pod communicates over a standard digital bus (RS-485) through a completely web-based GUI interface, and has a power consumption of less than 400 mW. Three-dimensional acceleration is measured by pure digital force-balance MEMS-based accelerometers. These accelerometers have a dynamic range of more than 115 dB and a frequency response from DC to 1000 Hz with a noise floor of less than $30ng_{rms}/{\surd}Hz$. Accelerations above 0.2 g are measured by a second set of MEMS-based accelerometers, giving a full 160 dB dynamic range. This paper describes the system design and the cooperative shared-time scheduler implemented for this project. Restraints accounted for include multiple data streams, integration of multiple free agents, interaction with the asynchronous world, and hardened time stamping of accelerometer data. The prototype of the device is currently undergoing evaluation. The first array will be installed in the spring of 2006.

• 한국잠사곤충학회지
• /
• 제15권1호
• /
• pp.37-48
• /
• 1973

The purpose of this studies is to improve the cohesion of raw silk through various analyses on cocoon drying, cooking, reeling, re-reeling, and on the properties of water. Also we investigated the correlation between silk testing items which we have reached to the following results. 1. Drying of cocoon When cocoons were slowly dried with 100$^{\circ}C$, the results of cohesion became much better. On the other hand, the results were considerably decreased in case the temperature with 115$^{\circ}C$. 2. Cooking of cocoon In case of the cooking of cocoon, we found that the result of cohesion was best with incomplete cooking, that of the control was next, while in over cooking, the results were very low. Also the results of cohesion were much better when using the method of over cooking with sericin arrestive agent than that of incomplete cooking with sericin agglutinating agent. 3. Reeling of cocoon A) When the temperature of reeling bath was 25-45$^{\circ}C$, the results of cohesion test were much better, but at the temperature below 25$^{\circ}C$ or above 45$^{\circ}C$, the results became worse. B) With out the process of croissieur, the results of cohesion were too bad, but in case of croissieur more than 1cm, cohesion became better rapidly. Further more, we understood that the results of cohesion were improving slightly with longer length of croissieur. C) When the velocity of reeling was increased, the results of cohesion also improved. The best results were shown when reeling velocity was 180-220 r.p.m. But when the velocity was increased more than 220 r.p.m., the results of cohesion got worse more or less. D) When the temperature of the drying pipe in reeling machine was raised, the results of cohesion also showed a tendency to improve. 4. Re-reeling A) We could net reach a conclusion as to have correlation between the number of dipping repeat in vacuum tank and the results of cohesion before re-reeling process. B) When we used Seracol 500 as an agglutination protective agent with l/1000 to l/2000 of water, the results of cohesion test were better. C) When we used Pearl-lite as an agglutination protective agent with 1/1000 to 1/2000 of water, the results of cohesion were considerably better. D) We gained tile best results when used Cohesion Improving Chemical, A-80, with 500-1500 times diluted. 1) Results of cohesion was improved when humidity was low or temperature was high in the rereeling machine. 5. Filature water A) The water pH near the isoelectric point of protein showed the best cohesion, but the farther water pH, the worser results were obtained. B) With the increasing of M-alkalinity in filature water, the results of cohesion were worse. Above all, we understood the tendency of the results of cohesion get worse when the M-alkalinity is increased above 200 ppm. C) By increasing the total hardness of the filature water, it improved the results of cohesion. Especially, when the total hardness was above 300ppm, the results were extremely high. 6. Effects combination of each results A) The result of effects combination in filature processes with the obtained best conditions was distinctively improved. But the results could not reach in mathematicaly double effect. When reelied under worse conditions, the results of cohesion test were too bad. There was "effect limit" for the promotion. B) Generally the results of cohesion were bad when the filature conditions(the temperature, pressure and the properties of water, etc) are processed as sericin loss to be high. On the other hand, the results were very good when lower sericin loss was controlled in filature conditions. C) When filature conditions such as reeling velocity and croissieur length provide pysical cohesion ability and when raw silk dry fast during reeling and re-reeling, we found the result of cohesion was better. 7. Correlation of silk testing items. A) A negative correlation exists between the results of cohesion test and cleanness defect. Another word, the result of cohesion test was found to be worse as cleanness defect increased. B) In cleanness, cohesion has negative correlation against the number of slugs, but we could not find any correlation against long loops, loose ends. C) Cohesion has negative correlation against average neatness and low neatness defect. The better the results of neatness respectively, the better the results of cohesion found. D) There is no correlation between tenacity and the results of cohesion test, but there was high positive correlation between the results of elongation and those of cohesion test. The more elongation, the better the results of cohesion was found.

• 한국농림기상학회지
• /
• 제12권4호
• /
• pp.225-231
• /
• 2010

강원도 주요 복숭아 재배지의 2010년 1월 7일의 일 최저기온 분포는 $-18{\sim}-29^{\circ}C$로서, 평년보다 $10^{\circ}C$ 이상 낮았으며 복숭아의 동해온도로 설정된 $-18^{\circ}C$보다 낮았다. 이로 인한 저온 피해 면적은 원주 144ha, 춘천 89ha, 영월 33ha, 횡성 22ha, 양구 17ha, 홍천 16ha 등이었다. 금후 강원 지역의 복숭아 동해에 대한 대책을 수립하는 데 기초 자료를 제공하고자 실제 동해 면적율과 휴면심도를 바탕으로 한 동해위험지수를 비교하였다. 자동기상측정장치가 설치된 지역의 일 최고기온과 일 최저기온, 기준온도를 바탕으로 계산한 장호원황도의 휴면심도는 -62 ~ -90였다. 휴면심도와 일 최저기온으로부터 계산된 동해위험지수는 51% 이상이었고, 이 동해위험지수는 실제 피해 면적 비율과 통계적으로 유의한 선형 관계를 나타내었다. 장호원황도의 휴면심도를 바탕으로 한 동해위험지수로 정확한 저온 피해 예측에는 어느 정도 한계가 있으나, 과수농가에서 복숭아의 동해를 대비하는 데 유용하게 활용할 수 있을 것으로 판단된다.

• 해양환경안전학회지
• /
• 제29권5호
• /
• pp.520-524
• /
• 2023

산갈치(Regalecus russellii)는 대부분을 심해에서 보내며 가끔 연안에 나타나는데, 그 이유는 명확히 알려져 있지 않다. 우리나라에서 산갈치는 주로 동해 연안을 따라 출현하는데, 특히 자망 등 어구에 의해 포획되는 경우와 연안에 좌초되어 출몰하는 경우가 높고 그 빈도는 극히 낮다. 또한 발견된다고, 하더라도 산갈치와 형태학적으로 유사한 투라치(Trachipterus ishikawae)로 판별되는 경우가 높다. 산갈치의 표본을 구하여 분석하는 것은 제한적이기 때문에, 이러한 이유로 우리나라 연안에 출현하는 산갈치의 생태학적 특징에 대해 거의 알려져 있지 않다. 본 연구는 2023년 3월 14일 강원도 앞바다에서 어획된 산갈치의 해부학적 특징을 관찰하였고, 해양 부이 자료를 이용한 수온 분석을 진행하였다. 분석 결과 산갈치는 수컷이었고, 전장은 320 cm, 전중은 27.52 kg, 체고는 26.62 cm, 생식소 중량은 619.45 g, 간중량은 218.71 g이었다. 산갈치의 위는 난바다 곤쟁이류로 가득 차 있었고, 산갈치가 어획되기 약 일주일 전부터 15~30 m 수심에서 강한 수온 변동이 있었으며, 저층 수온은 10℃ 미만이었다. 본 기술보고는 우리나라 동해 연안에서 나타날 수 있는 산갈치의 생태학적 특징을 이해하기 위한 기초 자료로 활용될 수 있을 것이다.

• 한국가스학회지
• /
• 제16권2호
• /
• pp.60-66
• /
• 2012

연구개발 활동의 다양화와 융합화에 따라 실험실에서 다양한 종류의 화학물질의 취급 사용과 함께 실험실의 수행업무도 복잡 다양해져 잠재위험이 크다. 또한, 실험조건이 극한의 온도와 압력 하에서 수행되는 경우가 많아 화재폭발 사고 등으로 인명 피해가 발생하고 있다. 본 연구에서는 대학과 연구기관의 실험실에서 화학물질 사용현황과 특성을 파악하여 실험종사자들의 안전성 확보를 위한 조사 도구로서 실험실 설문지를 개발하였다. 개발된 설문지를 이용하여 연구기관과 대학을 대상으로 전자우편과 방문조사로 화학물질 사용량과 폐기량 및 실험실 환경에 대한 인식도 조사를 실시하였다. 수집된 설문지 자료는 엑셀로 빈도 분석을 하여 실험실 사고예방 대책수립을 위한 기초 자료로 활용하고자 한다.

• 한국산업융합학회 논문집
• /
• 제27권1호
• /
• pp.207-212
• /
• 2024

Recently, with the strengthening of environmental regulations, there has been an increasing interest in eco-friendly energy sources, leading to a trend of the increasing scale of Cargo Containment Systems (CCS) for Liquefied Natural Gas (LNG) carriers. Among these systems, membrane tanks have gained popularity in LNG transport vessels due to their superior spatial utilization and competitiveness. However, due to high initial investment costs and the difficulty in repair in case of damage, a safety layer, the secondary barrier, must be installed without fail. In this study, in order to apply a new secondary barrier to the existing membrane-type LNG CCS, tests were conducted on the fiberglass layer previously used in the Triplex-Flexible Secondary Barrier (FSB), substituting it with basalt fiber. Tensile and vertical tensile tests were performed to assess the newly applied material. Environmental tests were conducted at room temperature (25℃) and extremely low temperatures (-170℃), considering the temperatures to which substances may be exposed during LNG vessel operations. The basalt-FSB produced in this study demonstrated superior results compared to the specifications of the existing product, confirming its potential applicability for implementation.

• 한국의류산업학회지
• /
• 제26권1호
• /
• pp.123-136
• /
• 2024

This study aimed to assess the mobility and thermal comfort of personal protective equipment (PPE) among female healthcare workers, taking into account wearers' physique and PPE protection levels. A total of 16 participants (age: 26.3 ± 8.3 y, height: 161.5 ± 7.3 cm, body weight: 57.1 ± 11.0 kg, BMI: 21.9 ± 3.6), representing diverse body types, underwent four PPE conditions: L (Low_Plastic gown ensemble), M (Medium_Tyvek 400), H (High_Tyvek 800J with Powered Air Purifying Respirator [PAPR]), and E (Extremely high_Tychem 2000 with PAPR, Bib apron, and Chemical-resistant gloves). The mobility protocol consisted of 10 different tasks in addition to donning and doffing. The 10 tasks were repeated twice at an air temperature of 24.3 ± 0.1℃, 59±4%RH. Findings revealed a disproportionate relationship between PPE protection and wearer discomfort. Significant differences in clothing microclimate and total sweat rate were observed between the lowest (L) and highest (E) protection levels (p < 0.01), while distinctions among medium levels were inconclusive. Subjective evaluations favored conditions H and L over M and E (p < 0.05), indicating reduced heat, and humidity, increased comfort, and lower exertion. Instances of mobility discomfort, specially in the small body type group, underscored the need for a suitable PPE size system for Korean adult female medical workers. Furthermore, enhancements in gloves, shoe cover, and PAPR hood designs are essential for improving ease of movement and preventing hindrance.

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.690-695
• /
• 2012

가스 하이드레이트는 순수한 물이 이루는 격자구조 내에 다양한 가스분자들이 선택적으로 포획되어진 고체상의 화합물로, 최근 이산화탄소를 포집, 수송, 저장 하는 CCS (Carbon Capture and Storage)기술에 이를 응용하려는 연구가 활발히 진행되고 있다. 가스 하이드레이트를 적용한 CCS 기술의 핵심은 효과적으로 $CO_2$ 하이드레이트를 제조하는 기법의 개발이며, 본 연구에서는 초음파 노즐을 이용하여 수십 나노미터 직경의 미세수적을 통해 고속의 $CO_2$ 하이드레이트 제조기술 개발하였고, 이 과정의 특성을 파악해 보았다. 주파수 2.4 MHz의 초음파 노즐을 이용하여 미세직경의 수적을 분무하고 이송가스(carrier gas)로 $CO_2$를 적용, 미세 수적과 $CO_2$가 동시에 급속 냉각되는 저온 반응기에 도입되어 다공질 얼음입자가 직접 평균 $10.7{\mu}m$ 직경의 $CO_2$ 하이드레이트로 생성되는 연속공정을 개발하였다. 미세직경 얼음입자를 시작물로 하여 정압조건에서 $CO_2$ 하이드레이트가 생성되도록 하며 가스포집량을 측정, 그의 가스 포집속도를 알아본 결과, 미세직경이며 동시에 다공 얼음이 제공하는 높은 기-고 접촉면적으로 인해 가스 하이드레이트 생성에 매우 적합한 것을 알 수 있었으며, 제조된 $CO_2$ 하이드레이트의 자기보존효과(self-preservation effect)를 실험으로 확인함으로서 $CO_2$ 가스의 수송에도 이용 가능함을 알 수 있었다.

• 한국식품저장유통학회:학술대회논문집
• /
• 한국식품저장유통학회 2001년도 임시총회 및 제18차 학술발표회 발표논문초록집
• /
• pp.51-64
• /
• 2001

The qualities including taste of sweetpotato stored during the winter which can display in the spring market in Korea are affected by availability of storage for the roots. In order to make high storage availability of sweetpotato, the postharvest handlings should be done thoroughly from the moment of harvest until shipping them to the market. A lot of procedures that must be handled carefully for improving postharvest management are as follows; digging, trimming, gathering, putting in storage containers, carrying them from field to house, curing, storing, washing, drying, selecting marketable roots, packing and shipping to the market, etc.. Sweetpotatoes have a high moisture content, and a relatively thin and delicate skin, and are sensitive to chilling, so careless postharvest handling can lead to both quantitative and qualitative losses which may be extremely high in some circumstances. From now on research has concentrated on the improvement of postharvest conditions to increase yield and lower disease rates. Storage, which makes sweetpotatoes available through out the year, benefits both the producer and the consumer. Seven very important points must be needed in order to get the best quality marketable roots in the storing of sweetpotatos : $\circled1$The storage house must be clean and sanitary, $\circled2$The crop must be harvested before the first frost to avoid low-temperature injury, $\circled3$Particular care must be taken to avoid cutting, bruising, or other injuries of the sweetpotatoes during digging, picking up, grading, placing in containers, and moving to the storage house, $\circled4$Select sound, disease-free roots for storage $\circled5$Sweetpotatoes should be stored in properly stacked containers $\circled6$Cure immediately after harvest, preferably at 32∼33$^{\circ}C$ and 90 to 95 percent relative humidity for 4 to 7 days, After curing the temperature should be reduced to 13$^{\circ}C$ to 16$^{\circ}C$ by ventilating the storage with outside air. $\circled7$Store at 12$^{\circ}C$ to 14$^{\circ}C$ and a relative humidity of 80 to 85 percent. Storage houses should be located on suitable sites and should be tightly constructed and insulated so that temperature and humidity will be uniform. Sweetpotatoes are usually not washed and graded, and lately sometimes washed, graded, waxed, before being shipped to market. Consumer packaging of sweetpotatoes in paper boxes(10-15kg) or film bags is done mainly to aid marketing. The shelf life of washed roots in consumer packs in only 1 to 2 weeks. Weight loss of roots during marketing is much less in perforated film bags than in mesh and paper bags. Perforation of 0.8 to 1kg polyethylene bags with about six 6mm holes is essential ; to lower the internal relative humidity and avoid excessive sprouting, rooting, and dampness. Development and use of better postharvest handling with good storage facilities or marketing methods can minimize sweetpotate losses and has an effect of indirectly increasing productivity and farmer’s income.

• 한국작물학회지
• /
• 제31권1호
• /
• pp.9-15
• /
• 1986

1983년부터 1984년까지 2년간에 걸쳐 통일형품종인 남풍벼와 태백벼, Japonica 품종인 서남벼와 당진벼를 공시하여 파종시기를 1모작 적파에 해당하는 4월 15∼20일, 2모작 만파에 해당하는 5월 10일의 두 시기로 각피부자재를 이용한 간양육묘방법 시험을 작물시험장 답작포장에서 실시하였던 결과를 요약하면 다음과 같다. 1. 중북부 1모작 지대에서 한파 및 적파 상자육묘시에는 비닐터널+silverpoly멀칭 또는 비닐터널+부직포멀칭구가 야간온도가 높고 주야간의 온도교차가 적어 발아율이 높았으며 뜸묘발생이 적었을 뿐 아니라 차광에 의한 백화묘발생이 적었다. 2. 남부 2모작 기계이앙용 만파육묘시에는 관행 비닐터널구 보다 silverpoly 또는 부직포터널구가 차광으로 인한 주간 온도의 저하로 고온장해의 위험성이 적고 출아록화기의 광조절이 가능하여 출아율이 높고 묘생육이 양호하였다. 3. 중북부지망 기계이앙 적파육묘는 간양출아후 보온밭못자리 및 보온절애못자리에 치상하고 록화기에 비닐터널 위에 silverpoly 또는 부직포를 멀칭하는 것이 록화관리가 양호한 편이다. 4. 남부 2모작지대 기계이앙재배를 위한 만파육묘에서는 보존 비닐터널 대신 silverpoly 또는 부직포터널로 못자리출아육묘를 하더라도 건묘육성의 가능성이 인정되었다.