• Wind and Structures
• /
• v.38 no.2
• /
• pp.119-128
• /
• 2024

The aerodynamic damping is an essential factor that can considerably affect the dynamic response of the cable-stayed bridge induced by crosswind load. However, developing an accurate and efficient aerodynamic damping model is crucial for evaluating the crosswind load-induced response on cable-stayed bridges. Therefore, this study proposes a new method for identifying aerodynamic damping of the bridge structures under crosswind load using an extended Kalman filter (EKF) and the particle filter (PF) algorithm. The EKF algorithm is introduced to capture the aerodynamic damping ratio. PF technique is used to select the optimal spectral representation of the noise. The effectiveness and accuracy of the proposed solution were investigated through full-scale vibration measurement data of the crosswind-induced on the bridge's girder. The results show that the proposed solution can generate an efficient and robust estimation. The errors between the target and extracted values are around 0.01mm and 0.003^o, respectively, for the vertical and torsional motion. The relationship between the amplitude and the aerodynamic damping ratio is linear for small reduced wind velocity and nonlinear with the increasing value of the reduced wind velocity. Finally, the results show the influence of the level of noise.

• Geophysics and Geophysical Exploration
• /
• v.19 no.1
• /
• pp.29-36
• /
• 2016

Recently, the studies about rock physics model (RPM) in shale reservoir are widely performed. In shale reservoir, the degree of the maturity can be estimated by kerogen and GOR (Gas-Oil Ratio). The researches on the rock physics model of shale reservoir with the amount of kerogen have been actively carried out but not with GOR. Thus, in this study, we analyzed the changes in seismic velocity and density, and AVO (Amplitude Variation with Offset) response depending on changes in GOR and the amount of kerogen. Since the shale consists of plate-like particles, it has vertical transverse isotropy (VTI). Therefore we estimated the seismic velocity and density by using Backus averaging method and analyzed AVO responses based on these estimated properties. The results of analysis showed that the changes in the velocity with the GOR variation are small but the velocity changes with the variation in kerogen amount are relatively larger. In case, GOR 180 (Litre/Litre) which is boundary between heavy oil and light oil, when volume fraction of kerogen increased from 5% to 35%, the P-wave velocity normal to the layering increased 51%. That is, it helps estimating maturity of kerogen through the velocity. Meanwhile, when rates of oil-gas mixture are large, the effect of GOR variation on the velocity change became larger. In case volume fraction of kerogen is 5%, the P-wave velocity normal to the layering was estimated $1.46km/s^2$ in heavy oil (GOR 40) but $1.36km/s^2$ in light oil (GOR 300). The AVO responses analysis showed class 4 regardless of the GOR and amount of kerogen because variation of poisson's ratio is small. Therefore, shale reservoir has possibility to have class 4.

• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.13-18
• /
• 2013

Slider bearing is a widely used load-carrying element in the industry. While a large number of studies have investigated the effect of overall surface curvature, very few have considered sinusoidal surface. Recently, consideration of surface roughness/waviness or intentional wave design has been identified as an important issue in the manufacture of hard disk driver, mechanical seal, hydraulic machine, and etc. This study investigated the load-carrying capacity of a finite-width slider bearing with a wavy surface. Film thickness ratios, length-width ratio, ambient pressure, amplitude, and partial distribution were selected as the simulation parameters. The calculation results showed that the load-carrying capacity rapidly varied at small film thickness ratio, but the waviness near the area of minimum film thickness made much more influence with an increase in film thickness ratio. As the length-width ratio of bearing was increased, ambient pressure became more influential at small film thickness ratios. Furthermore a particular partial distribution of the wavy area led to higher load-carrying capacity than did the whole distribution. Consequently, the results of this study are expected to be of use in surface micro-machining of finite-width slider bearings.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.12
• /
• pp.27-37
• /
• 2011

Uplift phenomenon occurs when the apparent unit weight of buried geo-structures becomes smaller than that of the liquefied backfill due to the increase of an excess pore water pressure during strong earthquakes. In order to explain the relationship between the uplift displacement of the buried geo-structures and the increase of the excess pore water pressure ratio in backfill, dynamic centrifuge model tests are conducted. In the present study, primary and secondary factors against uplift behavior of the buried geo-structures are considered in the dynamic centrifuge model tests. Among these factors, the most important factors affecting the increase in the excess pore water pressure ratio were the ground water depth, the relative density of backfill, and the amplitude of the input acceleration, which were also largely affect the uplift amount of the buried geo-structures.

• Journal of the Korean Ceramic Society
• /
• v.35 no.8
• /
• pp.813-818
• /
• 1998

A simple method to measure the elastic modulus E and Poisson's ratio v of diamod-like carbon (DLC) films deposited on Si wafer was suggested. Using the anisotropic etching technique of Si we could make the edge of DLC overhang free from constraint of Si substrate. DLC film is chemically so inert that we could not on-serve any surface damage after the etching process. The edge of DLC overhang free from constraint of Si substrate exhibited periodic sinusoidal shape. By measuring the amplitude and the wavelength of the sinu-soidal edge we could determine the stain of the film required to adhere to the substrate. Since the residual stress of film can be determine independently by measurement of the curvature of film-substrate com-posite we could calculated the biaxial elastic modulus E/(1-v) using stress-strain relation of thin films. By comparing the biaxial elastic modulus with the plane-strain modulus E/(1-{{{{ { v}^{2 } }}) measured by nano-in-dentation we could further determine the elastic modulus and Poisson's ratio independently. This method was employed to measure the mechanical properties of DLC films deposited by {{{{ { {C }_{6 }H }_{6 } }} rf glow discharge. The was elastic modulus E increased from 94 to 169 GPa as the {{{{ { V}_{ b} / SQRT { P} }} increased from 127 to 221 V/{{{{ {mTorr }^{1/2 } }} Poisson's ratio was estimated to be abou 0.16∼0.22 in this {{{{ { V}_{ b} / SQRT { P} }} range. For the {{{{ { V}_{ b} / SQRT { P} }} less than 127V/{{{{ {mTorr }^{1/2 } }} where the plastic deformation can occur by the substrate etching process however the present method could not be applied.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.25 no.2
• /
• pp.339-344
• /
• 2011

The purpose of this study was to evaluate the relationship of Inyoung-Chongu pulse, body mass index (BMI) and Sasang constitution using pulse diagnosis device in college women. We measured the amplitude of Inyoung pulse, Chongu pulse, ratio of Inyoung to Chongu and ratio of Chongu to Inyoung on 69 college women. The data was analyzed by ANOVA and Pearson's correlation coefficient using SAS program. The results were as follow. There was no significant difference in Inyoung pulse, Chongu pulse, Inyoung to Chongu ratio and Chongu to Inyoung ratio according to BMI and Sasang constitution. There was significant difference in BMI among Sasang constitution. BMI was significantly high in Taeeumin than in Soyangin and Soeumin. We concluded that there was no relation among Inyoung-Chongu pulse, BMI and Sasang constitution. Therefore, we need to expand the sample size for in depth study.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.66-78
• /
• 2021

In this study, the effect of Symmetry Breaking was compared according to the equivalent ratio condition and the number of nozzles where combustion instability occurs in an annular combustor. Generally, due to the relatively short combustor length, a longitudinal instability was less likely to occur in the annular combustor, but the combustion instability sometimes happens when ducts such as transition piece in gas turbine power station are present. In this case, due to the duct, only the longitudinal instability mode is observed. The characteristics of Symmetry Breaking were investigated according to the number of five lean nozzles and the equivalent ratio combination, and as the equivalent ratio decreased, the effect of Symmetry Breaking rapidly occurred, and the instability was dramatically disappeared and the amplitude was greatly reduced. In addition, it was confirmed that as the number of lean nozzles increased, a phenomenon such as a reduction in the equivalent ratio appeared.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.10
• /
• pp.1894-1899
• /
• 1994

In this paper, a new identification method is proposed for unknown digitally modulated input signals. The proposed identification method is implemented using a self-organized neural network which is based on the characteristic features of the symbol magnitude; the number of symbol magnitude levels, amplitude probability density and adjacent symbol magnitude ratio. The proposed method was performed for 5 QAM signals. The simulation results show that the self-organized neural network can accurately recognize all kinds of patterns even at SNR 8dB. The proposed method can be applied to the intelligent communication system on ISDN and multi-point polling networks.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.431-438
• /
• 1999

An assessment of liquefaction potential is made in principle by comparing the shear stress induced by earthquake to the liquefaction strength of the soil. In this study, a modified method based on Seed and Idriss theory is developed for evaluating liquefaction potential. The shear stress in the ground can be evaluated with seismic response analysis and the liquefaction strength of the soil can be investigated by using cyclic triaxial tests. The cyclic triaxial tests are conducted in two different conditions in order to investigate the factors affecting liquefaction strength such as cyclic shear stress amplitude and relative density. And performance of the modified method in practical examples is demonstrated by applying it to liquefaction analysis of artificial zones with dimensions and material properties similar to those in a typical field. From the result, the modified method for assessing liquefaction potential can successfully evaluate the safety factor under moderate magnitude(M=6.5) of earthquake.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.36-41
• /
• 2006

In this paper, we present the performance of iterative decoding with a Turbo decoder and a M-ary QAM(Quadrature Amplitude Modulation) demapper. The demappers are designed with Max-Log-MAP algorithm and it's approximated one. In addition, we provide implementing block for the approximated algorithm. From the results of computer simulations, the approximated algorithm of the Max-Log-MAP has little bit worse than the Max-Log-MAP but suggests low complexity for practical implementation.