• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1205-1214
• /
• 2013

Recently spaceborne SAR systems are increasing image resolution and frequency. As a high quality image resolution, the wider bandwidth is required and a wideband signal generator with RF component is very complicated and RF impairments of device is increased. Therefore, it is very important to improve performance by reducing these errors. In this study, the transmission signal of the wideband signal generator is applied to the phase noise, IQ imbalance, ripple gain, nonlinear model of high power amplifier. And we define possible structures of wideband signal generator and measure the PSLR and ISLR for the performance assesment. Also, we extract error of the amplitude and phase from the waveform and use a quadratic polynomial curve fitting and examine the performance change due to nonlinear device. Finally, we apply a high power amplifier predistortion method for non-linear error compensation. And we confirm that distortion in the output of the amplifier by intermodulation component is decreased by 15 dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11A
• /
• pp.933-940
• /
• 2011

In this paper, Ka-band transceiver for road watch radar system is designed and fabricated. The transceiver for road watch radar system is composed of waveform generator, frequency generator. IF transceiver and RF up/down converter. The transceiver especially has 3 different waveform mode for target detection range. The transceiver had over 150 MHz bandwidth in Ka-band and 22 dBm output power. The receiver gain and noise figure was 30 dB and 4 dB respectively. The receive dynamic range was 65.28dB and amplitude imbalance and phase imbalance of I/Q channel was 0.3 dB and 1.8 degree respectively. The transceiver meets the required electrical performances through the individual tests.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.12
• /
• pp.553-558
• /
• 2002

In this paper, an integrated balun using bondwire transformer is fabricated and measured. The bondwire transformer has 1ow conductor and substrate loss and kas high resonance frequency. So it is available to implement low loss broadband balun. From the measured results, 0.7 dB amplitude imbalance and about 2.5 $^{\circ}$ phase imbalance was achieved from 8.15 to 16.18 GHz. It is expected that the proposed balun can improve the performance of mixers, amplifiers and matching networks of antennas. It can also be integrated with other components due to its easier fabrication and smaller size than spiral transformer balun.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1830-1843
• /
• 2018

In this paper, the generation of a reference current and voltage signal based on a Kalman filter is offered for a 3-phase 4wire UPQC (Unified Power Quality Conditioner). The performance of the UPQC is improved with source voltages that are distorted due to harmonic components. Despite harmonic and frequency variations, the Kalman filter is capable enough to determine the amplitude and the phase angle of load currents and source voltages. The calculation of the first state is sufficient to identify the fundamental components of the current, voltage and angle. Therefore, the Kalman state estimator is fast and simple. A Kalman based control strategy is proposed and implemented for a UPQC in a distribution system. The performance of the proposed control strategy is assessed for all possible source conditions with varying nonlinear and linear loads. The functioning of the proposed control algorithm with a UPQC is scrutinized and validated through simulations employing MATLAB/Simulink software. Using a FPGA SPATRAN 3A DSP board, the proposed algorithm is developed and implemented. A small-scale laboratory prototype is built to verify the simulation results. The stated control scheme for the UPQC reduces the following issues, voltage sags, voltage swells, harmonic distortions (voltage and current), unbalanced supply voltage and unbalanced power factor under dynamic and steady-state operating conditions.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.268-275
• /
• 1999

In this paper, a new type of linearization technique proposed, in which the predistortor was added to the feedforward linearizer. As the input power level is applied to HPA, the gain and phase characteristics of the amplifier are also varied. By using of the predistorter the amplitude imbalance and phase imbalance is kept constant. Experimental results are present for Korea PCS frequency band. The center frequency of the feedforward amplifier is 1.843.75 MHz with 1.23 MHz bandwidth. The 2-tone intermodulation distortion at 37dBm output power is about -50dBc, and spurious emission are -46dBc at $fc{\pm}\;885KHz\;and\;-52dBc\;at\;fc\;{\pm}1.98MHz$, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.919-923
• /
• 2003

In this paper, a double-sided planar balun using Microstrip-to-CPW coupled structure is fabricated and measured. The measured amplitude and phase imbalance are, respectively, less than 0.2 dB and 2.1$^{\circ}$ in a wide frequency range from 2.44 GHz to 4.33 GHz. It is expected that the proposed balun can improved the performance of balanced mixer, amplifier and feeding network of antennas. Also, it can be used in many microwave multilayer structures due to its structural characteristics.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.44-50
• /
• 2004

In this paper, a DBM(Doubly Balanced Mixer) of 2 GHz is implemented on FR4 substrate. The structure of doubly balanced mixer requires, in general, two batons and a quad diode. For balun, a novel planar balun using microstrip to CPS is suggested and designed. The suggested balun shows the phase imbalance of 180$^{\circ}$${\pm}$ 1.5$^{\circ}$and the amplitude imbalance of ${\pm}$ 0.2 ㏈ for 1.5 to 2.5 GHz. Using the balun, DBM is succesfully implemented, and the measured conversion loss of up/down converter show about 6 ㏈ over the bandwidth. The balun may be applicable for MMIC DBM with the process supporting backside via thourgh more study.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.111-117
• /
• 2007

In this paper, a new marchand balun using broadside-coupled coplanar waveguide(CPW) on flexible printed circuit (FPC) is proposed. The proposed balun is designed based on the coupled line theory. The fabricated balun shows compact size and improved performance compared to the conventional microstrip line marchand balun. Measured amplitude and phase imbalance between the two balanced output ports are within 0.2 dB and $1^{\circ}$ respectively in a wide frequency range($1.63{\sim}3.44$ GHz). The proposed balun is expected to be used between various antennas and RF front-ends as a functional interconnection.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.94-100
• /
• 2014

In this paper, a design of low power Current-Reuse Voltage Controlled Oscillator (VCO) which has wide tuning range about 1.95 GHz ~ 3.15 GHz is presented. Class-C type is applied to improve phase noise and 2-Step Auto Amplitude Calibration (AAC) is used for minimizing the imbalance of differential VCO output voltage which is main issue of Current-Reuse VCO. The mismatch of differential VCO output voltage is presented about 1.5mV ~ 4.5mV. This mismatch is within 0.6 % compared with VCO output voltage. Proposed Current-Reuse VCO is designed using CMOS $0.13{\mu}m$ process. Supply voltage is 1.2 V and current consumption is 2.6 mA at center frequency. The phase noise is -116.267 dBc/Hz at 2.3GHz VCO frequency at 1MHz offset. The layout size is $720{\times}580{\mu}m^2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.558-565
• /
• 2013

In this paper, modeling and simulation for performance analysis of high resolution SAR system has been carried out in the time, frequency and numeric domain using ADS Ptolemy simulation tool of Agilent corporation. SAR system consists of antenna, controller and transceiver. Error parameters affecting SAR system performances have been defined, modeled and simulated such as phase noise of frequency synthesizer, amplitude and phase characteristic of TWTA, sampling frequency of waveform generator and I/Q imbalance. Finally, the development requirements of SAR system based on the impulse response function have been derived.