• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.579-584
• /
• 2005

Nowadays heat exchangers that have been applied for freon refrigerating systems, a shell and tube type condenser and a flooded evaporator have been used, but because of their large size, large space for installation and amount of refrigerants are needed. In this study, we will find the most suitable operating condition of shell and disk type optimum heat exchanger which can minimize the amount of a refrigerant and allow its minimum leakage. The condensing pressure of refrigeration system is increased from 15.0bar to 16.0bar and degree of superheat is increased from 0 to $10^{\circ}C$ at each condensing pressure. As a result of study, It revealed that shell and disk type heat exchanger was applicable to the freon refrigeration system

• 소성∙가공
• /
• 제6권5호
• /
• pp.435-445
• /
• 1997

In order to study the manufacturing possibility of connecting rod by direct quenching method, the difference between connecting rod by direct quenching and that by general heat treatment were investigated by observing microstructure, by measuring mechanical properties, by conducting fatigue testing, and by measuring the amount of tool wear in actual cutting. Connecting rod manufactured by direct quenching had better fatigue life than that by general heat treatment, which was due to homogeneous microstructure, and higher strength. The amount of cutting tool wear of connecting rod by direct quenching was higher than that by general heat treatment, which was due to low machinability and high toughness of tempered martensite microstructure. Therefore it will be added the study of heat treatment and cutting condition for manufacturing by direct quenching.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.133-139
• /
• 1996

As construction technology advances, most of civil engineering structures are becoming larger and taller. Therefore, high strength concrete is necessary for them. For high strength concrete, it needs a large amount of unit cement content and low water-cement ratio inevitably, so that a large amount of heat occurs in concrete. The thermal cracks make the durability and quality of concrete structures become worse, result from temperature rise and thermal stress due to heat of hydration. In this study, the proposal of using ground granulated blast furnace slag, fly ash and chemical admixtures was investigated to decrease the temperature rise of concrete.

• 한국컴퓨터정보학회논문지
• /
• 제20권12호
• /
• pp.67-74
• /
• 2015

The heat conduction equation, a type of a Poisson equation which can be applied in various areas of engineering is calculating its value with the iteration method in general. The equation which had difference discretization of the heat conduction equation is the simultaneous equation, and each line has the characteristic of expressing in sparse matrix of the equivalent number of none-zero elements with neighboring grids. In this paper, we propose a data structure for sparse matrix that can calculate the value faster with less memory use calculate the heat conduction equation. To verify whether the proposed data structure efficiently calculates the value compared to the other sparse matrix representations, we apply the representative iteration method, CG (Conjugate Gradient), and presents experiment results of time consumed to get values, calculation time of each step and relevant time consumption ratio, and memory usage amount. The results of this experiment could be used to estimate main elements of calculating the value of the general heat conduction equation, such as time consumed, the memory usage amount.

• Advances in concrete construction
• /
• 제6권6호
• /
• pp.659-677
• /
• 2018

The use of some superplasticizers in the production of mortar or concrete influences the hydration kinetic and the amount of total heat. This results in a modification of some properties, namely mortar workability, mechanical strength and durability. Three superplasticizers were used; a polynaphthalenesulfonate (PNS), a melamine resin (PMS) and a polycarboxylate (PC). They have been incorporated into various amount in a standardized mortar based on limestone cement. The aim of this study was to evaluate the rheological, mechanical and Calorimeters properties of this mortar. This will select the most compatible product and more able to be used depending on the climate of the country and the cement used. The PNS is incompatible with this type of cement registering a decrease of strength but the PMS and the PC modify the kinetics of hydration with significant heat generation and improved mechanical strength. The measured heat flow is significantly influenced by the type and dosage of superplasticizer especially for low dosage. Hydration heat and compressive strength of the different mixtures can be evaluated by determining their ultimate values and ages to reach these values where the correlation coefficients are very satisfactory.

• 한국세라믹학회지
• /
• 제23권5호
• /
• pp.67-74
• /
• 1986

To investigate the effects of unreacted silicon on the $\alpha$/$\beta$transfornation variation of morphology and mechanical strength of Sintered Reaction Bonded Silicon Nitride the mixtures of $\alpha$-$Si_3N_4$ and Si powder and Reaction Bonded Silicon Nitride were heat treated. The heat-treatments were performed in Ar atmosphere in order to inhibit the nitridation of silicon. In the mixtures heat-trated at 1$700^{\circ}C$ the amount of $\beta$-TEX>$Si_3N_4$transformed from $\alpha$-TEX>$Si_3N_4$was sigmoidally increased and the equiaxed $\alpha$-TEX>$Si_3N_4$grains elongated with the amount of silicon and heat treating time. And large $\beta$-TEX>$Si_3N_4$grains grown into silicon were observed. On the other hand there was no change in the heat-treatment of pure $\alpha$-TEX>$Si_3N_4$In case of the heat-treatment of RBSN the same phenomena due to the silicon appearing from the decomposition of $\alpha$-Smatte and needle were observed. From the three point bending test the strength of the sintered specimens with the and without 5wt% silicon addition had 53Kg/$mm^2$ and 73Kg/$mm^2$ respectively.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.987-992
• /
• 1993

In order to synthesize the heat resistance ceramics of LAS system, we studied on preparing the fine powder with homogeneity by sol-gel method using metal alkoxide. Various results were obtained depending on the composition and process. When the amount of H2O added at initial stage is higher than 10mol/$\ell$, and when the amount of catalyst is 0.1mol/$\ell$, the particle size of synthesized hydrate becomes finer. On condition that partial prehydrolysis time of TEOS is more than 50 hours, the monosized fine powder is obtained(below 1${\mu}{\textrm}{m}$).

• 설비공학논문집
• /
• 제26권11호
• /
• pp.529-534
• /
• 2014

This research developed a hybrid heat pump system with the functions of dehumidification and heating, which uses simulated air that is like underground air, from an environmental chamber as a heat source. The system consisted of three evaporators and three condensers that were installed in series in the air passage, between the underground and load space. As results, the total amount of dehumidification was 2.726 kg/h, and the heating $COP_h$ was 1.84 at air intake temperature $17^{\circ}C$ and relative humidity 70%, which is a similar condition to underground air. We found that the total amount of dehumidification also increased with the air temperature and humidity. The system $COP_s$ was reached at 2.5, if we include the latent heat of dehumidification in the conventional heat pump system's COP.

• 공업화학
• /
• 제8권5호
• /
• pp.729-736
• /
• 1997

산업폐열을 활용하기 위해 금속염화물-암모니아계 화학열변환기를 설계하고 1kW-1hr 용량의 장치개발을 하였다. 이는 $170^{\circ}C$ 열원을 $210^{\circ}C$ 이상으로 승온시키는 화학열펌프 시스템으로서, 효율적인 화학반응기의 설계를 위하여 필요한 반응물의 양과 반응물의 조건 등을 산출하는 정적계산과 동적모사를 수행하였다. 모사결과 열교환면적이나 반응기내 염의 양 등의 변수에 따라 시스템의 온도와 출력이 변함을 알 수 있었고 또한 반응물질의 양과 겉보기밀도 및 장치구조의 영향을 고찰하고 최적조건을 결정할 수 있었다. 4단계 작동사이클에 따라 운전한 결과 온도 및 출력의 실험치는 모사치와 비교하여 양호한 결과를 얻었으며 이 화학열변환기는 일정온도로 승온시킬 수 있는 특징으로 인해 앞으로 산업공정에서 배출되는 폐열원을 활용할 수 있는 시스템으로서의 가능성을 확인하였다.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.61-68
• /
• 2016

Characteristics of dissimilar metal welds between alloy steel ASTM A387 Gr. 91 and carbon steel ASTM A516 Gr.70 made with Flux cored arc welding(FCAW) have been evaluated in terms of microstructure, mechanical strength, chemical analysis by EDS as well as corrosion test. Three heat inputs of 15.0, 22.5, 30.0kJ/cm were employed to make joints of dissimilar metals with E91T1-B9C wire. Post-weld heat treatment was carried out at $750^{\circ}C$ for 2.5 h. Based on microstructural examination, tempered martensite and lower bainite were formed in first layer of weld metal. The amount of tempered martensite was decreased and the amount of lower bainite was increased with increasing heat input and layer. Heat affected zone of alloy steel showed the highest hardness due to the formation of tempered Martensite and lower Bainite. Tensile strengths of dissimilar welds decreased with increasing heat inputs. Dissimilar welds seemed to have a good hot cracking resistance due to the low HCS index below 4. The salt spray test of dissimilar metals showed that the corrosion rate increased with increasing heat inputs due to the increase of the amount of lower Bainite.