• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.173-179
• /
• 2004

Breakup characteristics of liquid sheets formed by the impingement of two water jets, such as a breakup length and a breakup wavelength of sheet, were investigated as increasing the injection velocity up to 30m/s and the ambient gas pressure up to 4.0㎫. While round edged orifices formed a laminar sheet which has no waves on the sheet when the injection velocity is low, sharp edged orifices formed a turbulent sheet which has impact waves irrespective of the injection velocity. Thus we compared the differences of breakup characteristics between them. The results showed that the aerodynamic force significantly affects the breakup of laminar sheet when the gas based Weber number is higher than unity. It was also found that the turbulent sheets have three breakup regimes, i.e. expansion regime, wave breakup regime and catastrophic breakup regime according to the gas based Weber number.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.338-339
• /
• 2012

This study examined the friction and wear behavior of diamond-like carbon (DLC) films deposited from a radio frequency glow discharge using a hydrogen diluted benzene gas mixture. The DLC films were deposited on Si (100) and polished stainless steel substrates by r.f.-PACVD at hydrogen to benzene ratios, or the hydrogen dilution ratio, ranging from 0 to 2.0. The wear test was carried out in both ambient and aqueous environments using a home-made ball-on-disk type wear rig. The stability of the DLC coating in an aqueous environment was improved by diluting the benzene precursor gas with hydrogen, suggesting that hydrogen dilution during the deposition of DLC films suppress the initiation of defects in the film and improved the adhesion of the coating to the interface.

• 천문학회지
• /
• 제52권3호
• /
• pp.83-88
• /
• 2019

Using ALMA observations of the $^{13}CN$ and DCN lines in the massive star-forming region G33.92+0.11A, we investigate the CN/HCN abundance ratio, which serves as a tracer of photodissociation chemistry, over the whole observed region. Even considering the uncertainties in calculating the abundance ratio, we find high ratios (${\gg}1$) in large parts of the source, especially in the outer regions of star-forming clumps A1, A2, and A5. Regions with high CN/HCN ratios coincide with the inflows of accreted gas suggested by Liu et al. (2015). We conclude that we found strong evidence for interaction between the dense gas clumps and the accreted ambient gas which may have sequentially triggered the star formation in these clumps.

• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.852-859
• /
• 2000

The emission in the exhaust gas from diesel engine is effected by the fuel spray characteristics. The spray of D.I. diesel engine impinges on a piston cavity and a cylinder wall. It is very important to know exactly the distribution and behavior of the spray inside cylinder. The objective of this study is to develop more accurate evaporation model. The EPISO code was used to analyze the flow characteristics in the engine. The Wakil model and the Faeth model are applied to the EPISO code to analyze the behavior of impinging spray. And also experimental and numerical analysis were carried out. The spray behavior characteristics were investigated by changing injection pressure, ambient pressure and temperature. The behavior of impinging spray was strongly effected by the change of ambient pressure and temperature. The effects of evaporation and rebounding droplet should be considered.

• 한국대기환경학회지
• /
• 제13권4호
• /
• pp.269-284
• /
• 1997

The ambient concentrations of gaseous and particulate phase ionic species and gaseous organic species in the Yochon industrial estate were measured during the spring ans summer of 1996. A three-stage filter pack sampler was used to collect particles and gaseous species, and stainless steel air sampling containers were used to collect air samples for organic species analyses. The concentrations of ions in aerosol wree comparable to those measured in Seoul. Aerosols measured were acidic, thus, most volatile acidic species were in the gas phase. The concentrations of organic species were highly variable, implying those were strongly dependent on the emissions of organic species from petrochemical plants. The concentrations of a few hazardous organic components were higher than those in Seoul or some populated areas in USA.

• 한국분무공학회지
• /
• 제7권2호
• /
• pp.16-21
• /
• 2002

Liquefied petroleum gas (LPG) has been used as motor fuel due to its low emissions and low cost. This study addresses the analysis of the LPG spray behavior near injection nozzle. The LPG spray photographs are compared with sprays of diesel fuel at the same conditions. The LPG spray photos show that the dispersion characteristic depends very sensuously on the ambient pressure soon after injection. The spray angle is very wide in a low ambient pressure condition until the saturated pressure at this test condition, but the angle value is quickly reduced at the condition over the pressure.

• 한국분무공학회지
• /
• 제17권3호
• /
• pp.158-163
• /
• 2012

This paper presents spray characteristics of piezo-driven type common-rail injector and comparisons to those of solenoid-driven type. Experiments were conducted to measure spray penetraion and SMD distributions using a spray visualization system and PDPA (phase Doppler particle analyzer) system. Injection conditions including injection pressure and energizing durations were varied in order to analyzing effects of injection conditions on spray characteristics. Furthermore, ambient pressures were increased for keeping ambient gas density close to in-cylinder pressure of diesel engine. Results showed that injection delay of piezo-driven type injector was much shorter than those of solenoid driven type and exhibited enhanced atomization performances.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권3호
• /
• pp.103-108
• /
• 2005

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266nm. Before post-annealing treatment in the oxygen ambient, the experiment of the deposition of ZnO thin films has been performed for substrate temperatures in the range of $300\~450^{\circ}C$ and oxygen gas flow rate of $100\~700\;sccm$. In order to investigate the effect of post-annealing treatment of ZnO thin films, films have been annealed at various temperatures after deposition. After post-annealing treatment in the oxygen ambient, the structural properties of ZnO thin films were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM) and the optical properties of the ZnO were characterized by photoluminescence(PL).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.828-830
• /
• 2000

Various substrates were compared for the investigation of the optical properties of ZnO thin films. ZnO thin films have been deposited on (100) p-type silicon substrates and (001) sapphire substrates by pulsed laser deposition technique using a Nd:YAG laser with the wavelength of 355 nm. Oxygen and nitrogen gases were used as ambient gases. Substrate temperatures were varied in the range of 200$^{\circ}C$ to 600$^{\circ}C$ at a fixed ambient gas pressure of 350 mTorr. ZnO films have been deposited on various substrates, such as Si and sapphire wafers. We have investigated substrate effect on the optical and structural properties of ZnO thin films using X-ray diffraction (XRD) and photoluminescence (PL).

• 한국진공학회지
• /
• 제8권3A호
• /
• pp.218-223
• /
• 1999

We investigated the interfacial reactions between the $Y_2O_3$ film deposited by ICB processing and p-type (100) Si substrates upon annealing treatments in $O_2$ and Ar gas ambients. we also investigated the evolution of surface morphology of ICB deposited $Y_2O_3$ films upon annealing treatments. We observed that the root-mean-square(RMS) value of surface roughness measured by AFM increased with annealing time at $800^{\circ}C$ in $O_2$ ambient, while the change of surface roughness was not observed in Ar ambient. We also found the growth of $SiO_2$ layer and the formation of yttium silicate layer. From the capacitance values $(C_{acc})$ measured by C-V measurements, the relative didldctric constant of $Y_2O_3$ film in metal-insulator-semiconductor(MIS) structure was estimated to be about 9.