• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.78-81
• /
• 2005

The aluminum Subframe for automobile was developed using hybrid process, i.e. extruforming and press forming. To achieve a $30\%$ weight reduction compared with convensional steel subframe keeping satisfactory performance, the design of cross-section of extrusion part was initiated, then forming simulation was performed and the final design was determined. In addition, we tried to estibilish proper aluminum welding conditions for good penetration depth and few pore defact, finally the prototype of aluminum subframe was assembled using MIG welding method.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.5 s.54
• /
• pp.76-81
• /
• 2003

Friction welding of GCD45 spheroidal graphite cast iron and 2024 aluminum alloy has been studied, especially in terms of the joint faces and strength of friction welding. For appropriate results of the friction welding of GCD45 graphite cast iron and 2024 aluminum alloy, an insert of A1050 pure aluminum metal was used. The joint strength of the A1050 pure aluminum insert approached the maximum strength of 165.7Mpa, compared to 128MPa for the joint between GCD45 graphite cast iron and A1050 pure aluminum without the insert metal. Maximum strength, 165.7Mpa, was possible for the following optimum conditions: 20MPa for the friction pressure, P1, 60MPa for the upsetting pressure, P2, 1 second for the friction time, t1, 3000rpm for the rotation, N, and 0.3 seconds for the brake time, tB.

• Journal of Welding and Joining
• /
• v.11 no.1
• /
• pp.2-8
• /
• 1993

A literature review was conducted to gather informations available on the welding metallurgy of aluminum alloys, emphasized on characteristics in the heat affected zone(HAZ). Nominal metallurgical reactions that occur in aluminum alloys provide a basis for understanding aluminum welding metallurgy. However, welding reactions differ to some extent because of the relatively short times involved, and the non-isothermal heating excursed. For non-heat treatable alloys, welding primarily affects these alloys by annealing (recrystallization and growth) and to a less extent, changes in low temperature precipitates. In the case of heat treatable alloys, the resulting HAZ properties depend upon alloy composition, starting temper, heat input and post weld heat treatments.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.379-383
• /
• 2001

Resistance spot welding has been widely used in the sheet metal joining processes because of low cost, high productivity and convenience. Recently, automobile and aerospace industries are trying to replace partly steel sheets with aluminum alloy sheets. But in the case of dissimilar materials, to apply resistance spot welding has been known to be very difficult owing to the effect of melting temperature. On this study, an effort was made to apply spot welding of dissimilar sheet metals, 2024 aluminum alloy and zinc coated steel sheet, evaluate the spot weld quality with tensile-shear strength test and nondestructive evaluation technique, C-scan image methodology. In this study results, as the current below 11 kA, melting of materials is not achieved well. Also as the current exceeds to 13.5 kA, the more spatters happen at welded zone and tensile-shear strength lowered. So, the feasibility of C-scan image technique proposed in the study is found to be suitable evaluation method for resistance spot weldability.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.147-147
• /
• 2000

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.20-26
• /
• 2000

• Transactions of Materials Processing
• /
• v.26 no.2
• /
• pp.115-120
• /
• 2017

Porthole extrusion process is a very effective metal forming process to produce aluminum profiles with hollow sections. The structure of porthole extrusion die is very complex. In this process, the billet is divided by porthole bridge, and then the divided billet is welded in the welding chamber. The welding pressure in the welding chamber is very important. The higher welding pressure improves the quality of the aluminum profiles. Therefore, the objective of this study is to develop a new porthole extrusion die for improving the welding pressure in the welding chamber by using numerical analysis. The effectiveness of the new porthole extrusion die was verified by using numerical analysis. Through numerical analysis, the welding pressures in the welding chamber between the new porthole die and the conventional porthole die were compared with each other.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.8
• /
• pp.99-109
• /
• 2022

In this study, an electric resistance-heated surface friction spot-welding process was proposed and tested for the spot-welding ability of copper and aluminum dissimilar metal sheets using electric resistance heating and surface friction heating. This process has welding variables, such as the current value, energizing cycles, rotational speed, and friction time. The current value and energizing cycle can affect the resistance heat, and the rotational speed of the rotating pin and friction time influence frictional heat generation. Resistance heating before friction heating has a preheating effect on the Cu-Al contact interface and a positive effect on preventing friction heat loss during the friction stage. However, because resistance preheating can soften the copper sheet and affect the contact stress and friction coefficient, it has difficulties that may adversely affect frictional heat generation. Therefore, the optimal combination of welding variables should be determined through simulations and experiments of the spot-welding process to determine the effects of electric resistance preheating on the suggested process. Through this procedure, it is known that the proposed spot-welding process can improve the welding quality during the spot welding of Cu-Al sheets.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.110-114
• /
• 2000

This paper shows the possibility of performing the friction stir welding and the development of optimizing tools for FSW with 2mm thick plate of aluminum alloys using milling machine. This research can be reported on achieving above 90% of the tensile strength in 1050 aluminum alloys friction stir welded in the room temperature. This welding process is very simple and does not require filler metal eliminates straightening of the workpiece. It is currently attracting interest from different industries working with aluminum alloys.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.2
• /
• pp.145-150
• /
• 2011

There is problem to reduce the car body weight for improving fuel consumption and $CO_2$ generation. As one of the solution, the multi material car body concept using aluminum alloys and high strength steels is proposed recently. Therefore, new welding processes by which these dissimilar material can be joined in high reliability and productivity are demanded. Laser spot welding was developed for joining of dissimilar metals. In the present work, Laser spot welding of zinc coated steel and aluminum alloy was investigated, and the process parameters were studied. Otherwise, the influences of process parameters on the weldability, the formation of intermetallic compound layer and the mechanical properties have been investigated. When intermetallic compound layer thickness was more than 1mm, specimen was failure in the interface.