• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1656-1657
• /
• 2011

본 논문에서는 RF 프로브를 이용하여 평면 구조물의 RCS(Radar Cross Section)를 감쇄시키기 위한 방법을 제안하였다. 우선적으로, EM 시뮬레이터를 이용하여 제안한 방법에 대한 가능성을 증명한 후 실험을 수행하였다. x-band 에서 $10{\lambda}$의 알루미늄판 위에 FR4 기판을 이용하여 patch 형태로 제작된 RF 프로브를 설치하였으며, 그 후 알루미늄 판으로 입사되는 외부 전자파를 상쇄시키기 위하여 RF 프로브로부터 전자파를 방사하였다. 로테이터를 사용하여 알루미늄판을 phi 방향으로 회전하여 임의의 각도로 입사하는 평면파에 대해서도 반사파의 크기를 측정하였다. RF 프로브로부터 방사된 전자파의 세기와 위상은 신호 발생기와 위상 천이기를 이용하여 조절되었다. 결과적으로 무반향실에서의 실험을 통해, 알루미늄판에 의해 반사되는 전자파를 측정하여 외부 전자파의 상쇄 정도를 확인하였다.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.81-87
• /
• 1990

Fatigue crack closure levels based on the behavior of residual displacements on crack surfaces, are determined analytically according to the microscopic crack closure mechanisms, i.e., whether the first contact of crack surfaces takes place at the very crack tip or on the surfaces near the tip. The comparative analysis on the two models is carried out empirically by the constant amplitude fatigue tests on 2024-T3 aluminum alloy plate, and it shows that under negative stress ratio, the case of the first contact at crack tip gives better agreement with the experimental results than the other.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.87-87
• /
• 1990

Fatigue crack closure levels based on the behavior of residual displacements on crack surfaces, are determined analytically according to the microscopic crack closure mechanisms, i.e., whether the first contact of crack surfaces takes place at the very crack tip or on the surfaces near the tip. The comparative analysis on the two models is carried out empirically by the constant amplitude fatigue tests on 2024-T3 aluminum alloy plate, and it shows that under negative stress ratio, the case of the first contact at crack tip gives better agreement with the experimental results than the other.

• 한국가스학회지
• /
• 제4권1호
• /
• pp.33-39
• /
• 2000

긴 표면균열을 갖는 알루미늄합금(A5083)의 평판을 사용하여, 균열관통후의 응력확대계수를 검토하였다. 짧은 표면균열의 관통후에 제안된 식에 의하여 긴 표면균열 관통시의 평가는 균열종횡비가 적을수록 오차가 크게 되므로, 진전거동을 정확하게 평가하기 위해서는 수정이 필요하였다. 따라서 긴 표면균열 관통시의 종횡비를 고려하여, 응력확대계수의 평가식을 수정함으로써 관통후 고정도의 해석이 가능하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권3호
• /
• pp.437-445
• /
• 2008

This paper deals with the experimental assessment of the vibration suppression of the smart structures. First. we have presented a new high-speed active control system using the DSP320C6713 microprocessor. A peripheral system developed is composed of a data acquisition system, N/D and D/A converters, piezoelectric (PZT) actuator/sensors, and drivers for fast data processing. Next, we have tested the processing time of the peripheral devices, and provided the corresponding test results. Since fast data processing is very important in the active vibration control of the structures, we have focused on achieving the fast loop times of the control system. Finally, numerous experiments were carried out on the aluminum plate to validate the superior performance of the vibration control system at different control loop times.

• 소음진동
• /
• 제7권3호
• /
• pp.449-455
• /
• 1997

A theoretical study is presented for the prediction of the scattering of obliquely incident plane acoustic wave by transversely isotropic cylindrical shells immersed in water. In dorder to illustrate the vailidity of the theory backscattering form functions are compared with the existing results for degenerated problems: the catterings by isotropic shell and transversely isotropic solid cylinder. The unidirectional fiber reinforced boron-aluminum composites are selected as a model of transversely isotropic materials having potential applications in practice. From the resonant scattering analysis of the partial backscattering form functions, the dispersion curves for fluid-borne Stoneley wave, guided wave along the shell, and the lowest three Lamb type waves can be found. The Lamb type dispersions are compared with those of the flat plate. The variation of anisotropy significantly affects the properties of circumferential waves. From these results, it can be possible to identify parametrically the material properties of anisotropic cylindrical targets.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.216-221
• /
• 2002

In this paper, the transmitted noise reduction of smart panels of which passive piezoelectric shunt damping is used, is experimentally studied. Shunt damping experiments are based on the measured electrical impedance model. A passive shunt circuit composed of inductors, and a load resistor is devised to dissipate the maximum energy into the joule heat energy. For multi-mode shunt damping, the shunt circuit is redesigned by adding a blocking circuit. Also the optimal location of the piezoelectric patch is studied by FEM in order to cause the maximum admittance from the patch for each mode of aluminum plate. In results, the transmitted sound pressure level of panels is efficiently reduced for multi-modes

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.36-42
• /
• 2017

Helical gear excitation is transmitted to a gearbox through the shafts and bearings and the vibration of the gearbox radiates the noise in the air. Therefore gearbox modeling is essential to evaluate the gear noise. This work deals with vibration and acoustic analysis of a cylindrical shell-type gearbox with/without holes excited by helical gears and focuses on the development of the simple gearbox model. To do so, helical gears and bearing forces are calculated. Gearbox with/without holes is modeled by the aluminum end plates and PMMA cylindrical shell body. The vibration mode and the forced harmonic response were calculated by the commercial FE software and the end plate of the gearbox is more contributed to vibration than the body. Acoustic analysis was also conducted by the commercial acoustic software and a cylindrical shell type gearbox with/without holes has the similar vibro-acoustic characteristics.

• Smart Structures and Systems
• /
• 제4권5호
• /
• pp.565-582
• /
• 2008

This paper presents a feasibility study of flexible piezoelectric paint for use in wide-band low-profile surface-mount or embeddable ultrasonic sensor for in situ structural health monitoring. Piezoelectric paint is a piezoelectric composite with 0-3 connectivity. Because of its ease of application, piezoelectric paint can be readily fabricated into sensing element with complex pattern. This study examines the characteristics of piezoelectric paint in acoustic emission signal and ultrasonic guided wave sensing. A series of ultrasonic tests including pitch catch and pencil break tests were performed to validate the ultrasonic wave sensing capability of piezoelectric paint. The results of finite element simulation of ultrasonic wave propagation, and acoustic emission generated by a pencil lead break on an aluminum plate are also presented in this paper along with corresponding experimental data. Based on the preliminary experimental results, the piezoelectric paint appears to offer a promising sensing material for use in real-time monitoring of crack initiation and propagation in both metallic and composite structures.

• 설비공학논문집
• /
• 제13권7호
• /
• pp.612-620
• /
• 2001

The optimum design of a heat exchanger with porous media insertion is studied in this paper. It is considered that the aluminum foam metal is inserted in a flat plate channel and air flows through it. The influence of the microstructure of the foam metal on the pressure drop and heat transfer is investigated utilizing previous analytical results and existing correlation equations. Design parameters are identified as the unit-cell size and the ligament thickness of the porous medium, and their effects are examined. The results show that there exists optimum microstructure of the porous media maximizing heat transfer with a constant pressure drop. When the increase in the pressure drop is within a practically acceptable range, the increase in the heat transfer is dominated by the increase in the heat transfer area due to the porous medium insertion. Consequently, among the porous media with a constant pressure drop, the heat transfer is maximized with a microstructure with maximum specific surface area.