• Journal of Biomedical Engineering Research
• /
• v.43 no.4
• /
• pp.219-229
• /
• 2022

In this study, we propose a miniaturized micro-ceramic heater device. After screen-printing a silver paste between pre-sintered two aluminum oxide plates to integrate a heating circuit, the device was fabricated through a low-temperature sintering process. In order to configure the optimal heating circuit integration condition, the output current evaluation and heating test were performed according to the number of screen prints of the silver paste at various voltages. A silver paste-based heating circuit printed with a line width of 200 ㎛ and a thickness of 60 ㎛ was successfully integrated on a pre-sintered alumina substrate through a low-temperature sintering process. In the case of the 5 times printed device, the thermal response showed a response rate of 18.19 ℃/sec. To demonstrate feasibility of the proposed device in the medical field, such as bio-tissue suturing and hemostasis, a voltage was applied to pig tissue in the device to test tissue change due to heat generated from the device. These results show the possibility that the proposed small ceramic heater could be used in the medical field based on its excellent temperature response.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.104-105
• /
• 2020

Red mud is a highly alkaline waste by-product of the aluminum industry. Although recycling of red mud is being actively researched, a feasible technological solution has not been found yet. In this study, we propose that neutralization of red mud alkalinity could assist in its use as a construction material. Neutralized red mud ( pH 6-8) was prepared by adding sulfuric acid to liquefied red mud (pH 10-12). After adding liquid and neutralized red mud to the cement paste, the heat of hydration was measured. As a result of the experiment, the calorific value of the cement paste with liquid red mud was lowered and delayed compared to the cement paste with neutralized red mud.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.163-166
• /
• 2009

For the preparation of Aluminum-slurry fuel, the effects of process parameters on the aluminum dispersion stability in the liquid fuel have been investigated. The dispersion stability of aluminum-slurry fuels could be monitored by measurements through Turbiscan using the scattering of the Laser. Through the application of various additives, TPAB (Tetrapropyl ammonium bromide) showed more reasonable performance than others.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.77.2-77.2
• /
• 2010

스크린 프린팅을 이용한 태양전지에서 전극소성 시 알루미늄 후면 전극이 실리콘으로 확산되어 후면전계(Back Surface Field)를 형성한다. 후면전계 형성시 알루미늄과 후면전계 사이에 알루미늄-실리콘 합금이 형성된다. 이 알루미늄-실리콘 합금은 알루미늄 후면전극의 전기전도도 및 휨현상, bead 형성 등에 영향을 끼친다. 본 논문은 알루미늄 페이스트에 첨가된 Glass frit이 알루미늄-실리콘 합금 형성에 끼치는 영향을 관찰하였다. 분산제, 유기바인더, 알루미늄을 섞어 1개의 페이스트를 만들었고, Glass frit을 1%, 2%, 3%, 4%, 5% 씩 첨가하여 총 6개의 알루미늄 페이스트를 만들었다. 절삭손상이 제거된 실리콘 기판의 후면에 알루미늄 페이스트를 스크린 프린팅하여 전극을 소성하였다. 주사전자 현미경(SEM)을 사용하여 시편의 단면사진으로부터 Glass frit 함량에 따른 알루미늄-실리콘 합금층의 변화를 관찰하였다. Glass frit이 첨가되지 않은 페이스트는 소성 후 알루미늄-실리콘 합금이 두껍게 형성되었으나, Glass frit이 첨가된 페이스트는 소성 후 알루미늄-실리콘 합금이 얇게 형성되는 결과를 얻었다. 또한 Glass frit을 첨가함에 따라 표면의 원형 모양의 무늬가 작아지면서 3%부터는 사라지는 것을 확인할 수 있었다.

• Journal of Applied Reliability
• /
• v.6 no.3
• /
• pp.205-212
• /
• 2006

The purpose of this article is about the accelerated product-reliability-test method of the changing colors of mobile products, which are majorly from the frequent touching of sweating fingers. Such problems of changing colors of mobile products have found mostly In metallic paint containing aluminum paste pigments. Also we found that the color of Al Paste is changed by human sweat. Therefore, the accelerated experimental method has been tested as follow: applying the various concentration of lactic acid, which is the changing color components from human sweat, and deeping the testing sample under temperature of $60^{\circ}C$ in dilutelactic acid with water. From the series of tests, the most optimum concentration of lacticacid has been obtained in 10wt% and the sample is observed to be almost same effect as natural changing of colors by human touching after the test. It has been also confirmed from the cross-sectional analysis. In detail, the testing sample has changed its color in 48hr by changing color effect of Alpaste with 10 wt% of lactic acid, and the digit of $\Delta$ E has measured 10.9 after the test.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.333-340
• /
• 2019

Red mud is an industrial by-product produced during the manufacturing aluminum hydroxide (Al(OH)3) and aluminum oxide(Al2O3) from Bauxite ores. In Korea, aproximately 2 tons of red mud in a sludge form with 50% moisture content is produced when 1ton of Al2O3 is produced through the Bayer process. Neutralization of red mud will help to reduce the environmental impact caused due to its storage and also lessen significantly the ongoing management of the deposits after closure. It will also open opportunities for re-use of the residue which to date have been prevented because of the high pH. Moreover, attention to liquefied red mud(LRM) that does not require heating and grinding process for recycling is needed. In this paper, characteristics of compressive strength for cement paste with content of LRM neutralized by nitric acid and sulfuric acid. The results showed that compressive strength of cement paste with neutralized LRM is higher than that of cement paste with LRM.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.5
• /
• pp.457-464
• /
• 2013

Traditionally, the material used for the form in reinforced concrete construction has been wood or steel. But recently, aluminum forms have been widely used in wall structures such as apartment buildings. Aluminum is light, easy to handle, and economically advantageous, but the hydrogen gas created due to its reaction with the alkali component in concrete gives rise to air pockets on the concrete's surface, and deteriorates the surface's finishability. In this research, to determine the influence of aluminum material on concrete, the cement paste W/C and its chemical reactivity in alkali and acid solution were analyzed. As a prevention plan, the influence of the number of applications of calcium hydroxide and various surface coating materials was analyzed. Through the analysis, it was found that the surface voids on the aluminum form are the result of the reaction of hydrogen gas with an alkali such as $Ca(OH)_2$. This can be prevented by the surface treatment of $Ca(OH)_2$, separating material and coating material. However, poor surface form and damages to the form are expected to cause quality degradation because of the aluminum-concrete interaction. Therefore, thorough surface treatment, rather than the type of separating material or coating material, is considered the most important target of management.

• Journal of Powder Materials
• /
• v.10 no.6
• /
• pp.415-421
• /
• 2003

The study for producing the flake powders by milling of aluminum foil and gas atomized powders was carried out. The effects of lifter bars on the ball motions and milling of aluminum foils were also investigated. The aluminum foils were laminated each other, elongated, fragmented into small foils and finally formed into the flake powders during the dry ball-milling. The spherical atomized-powders were milled to coarse flake powders with high aspect ratio and then changed to fine flake powders with lower aspect ratio. Even though long times were required for making flake powders by milling of foils, the water covering areas of them were higher than those of powders milled using gas-atomized powders, suggesting aluminum foils were more plastically deformed by micro-forging. On the other hand, as the number of lifter bars increased, the necessary rotation speeds of milling jar for cascading mode and cataracting mode decreased drastically. It was possible to achieve same quality of milled flake powder by using the lifter bars under the lower milling speeds. The painting test showed that the appearance of painted surface was good and optimum content range of aluminum paste in car paint to maximize the degree of gloss was 3-5%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.121-124
• /
• 1998

Generally the structure of powder electroluminescent devices (PELDs) on ITO-film was makeup of the ZnS:Cu phosphor layer and BaTiO$_3$ insulating layer. The active layer, which consists of a suitably doped ZnS powder mixed in a dielectric, is sandwiched between two electrodes; one of which are ITO film and the other is aluminum. In this paper, three kinds of powder eleotroluminescent devices (PELDs) : WK-A(ITO/BaTiO$_3$/ZnS:Cu/Silver paste). WK-B(ITO/BaTiO$_3$+ZnS:Cu/Silver paste) and WK-C(ITO/BaTiO$_3$/ZnS:Cu/BaTiO$_3$/Silver paste), fabricated by spin coating method, were investigated. To evaluate the luminescence properties of three kinds of PELDs, EL emission spectroscopy, transferred charge density and time response of EL emission intensity under square wave voltage driving were measured.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.129-130
• /
• 2021

In order to solve the problem of low early-age compressive strength of high volume fly ash concrete. This paper studies the effect of 2% sodium sulfate (Na₂SO₄) as a chemical activator on the paste with 40% fly ash content and a water-binder ratio of 0.30. The results indicate that the addition of Na₂SO₄ can effectively improve the early-age compressive strength of the fly ash-cement system, and the strength improvement rate on the first day reached nearly 70%. In addition, calorimetric analysis reveals that the incorporation of Na₂SO₄ promotes the early hydration of cement and fly ash, increases the cumulative hydration heat and delays the heat peak of the aluminum phase.