• 한국주조공학회지
• /
• 제6권2호
• /
• pp.104-115
• /
• 1986

I A쪽과 II A쪽이 Al-Si 합금의 공정조직개량 처리에 효과적인 것은 잘 알려진 사실이나 Na(Sodium)과 Sr(Strontium)만 상업적으로 쓰여지고 있다. 그러나 휘발성과 산화하기 쉬운점때문에 Na 은 그 양을 정확하게 조절하기가 어렵고 특히 온도가 높은 경우 더욱 곤란하나 Sr 은 휘발성이나 산화성은 없으나 micro-또한 macro-porocity의 주 원인으로 보고 되고 있다. 희토류 금속 (예 : Cerium, Lanthanum,etc )도 개량처리 효과가 있다는 논문들(ref. 2, 3, 4, 5) 이 있고, 계속 연구되어 오고 있으나 그 세부사항과 효율성에 관해 정립된 바가 없다. 이런 연유로 Al-Si 합금의 생산을 위한 개량 처리제로서의 희토류 금속의 역할에 대해 구체적이고 세부적인 개량처리기구의 구명을 위해 이 연구가 이루어졌다. Al-Si 합금 356가 채택된 이유는 상업적 Al 주물의 생산을 감안해서 였다.

• 한국주조공학회지
• /
• 제11권6호
• /
• pp.491-497
• /
• 1991

Vanadium은 비중이 6.09로써 비교적 무거운 금속에 속하나 Al을 30wt% 이내로 첨가하여 $Ni_3Al$ 및 TiAl와 유사한 비강도가 크며 내열성을 지니는 V-Al합금을 얻을 가능성을 지니고 있다. 본 연구에서는 V-Al합금에 Si, Y, Ti, B등 제3원소를 첨가함에 따르는 미세 응고조직의 거동과 기계적 성질을 조사하였다. 알곤 분위기에서 제조된 V-30%Al합금은 상온에서 고용체와 취성이 큰 금속간 화합물인 $VAl_3$등 2상으로 존재하므로 용체화 처리 과정이 요구되며 24시간 이상 장시간 열처리에 의하여 단일 고용상을 이룰 수 있었다. 규소의 첨가는 금속간 화합물의 형성과 아울러 합금의 경도를 크게 증가시키는 경향을 나타내며 B을 0.3%정도가지 첨가할 때 경도가 낮아지는 현상이 관찰되었다. �c칭된 V-30%Al 합금은 입계면을 따라 decohesive rupture 현상을 나타내며 입자간 파괴 현상도 일부 관찰되었다.

• 한국주조공학회지
• /
• 제12권5호
• /
• pp.378-389
• /
• 1992

A numerical model based on the SOLA-VOF method, which can calculate the transient free-surface configuration of the melt, has been developed in order to analyze melt flow in the investment mold. The computational results were compared with experimental results obtained from pure aluminum investment casting. Heat transfer analysis, with and without consideration of melt flow effect has been performed. It can be concluded that analysis of melt flow in the investment mold, provides the optimum conditions for gating design. It also enables more precise solidification simulation, since heat loss, while filling the thin and complex investment mold, plays an important role in determining the solidification sequence.

• 한국주조공학회지
• /
• 제12권1호
• /
• pp.32-39
• /
• 1992

In this study, electron microscopy, Fractography and $J_{IC}$ test have been used to investigate the fracture behaviour in the scope of aging temperature which 7075 Al-alloy can have high strength. Conclusions obtained on this study are as followed. 1) When the 7075 Al-alloy was aged for 24hrs at $120^{\circ}C$, it's mechanical properties was excellent but fracture toughness decrement resulted from intergranular fracture was emerged. 2) The state of aged for 24hrs at $100^{\circ}C$, had the highest fracture toughess. 3) We could infer that intergranular fracture occurred because preferrential precpitated precipitates in the grain boundary growed in the form of colinear along the grain boundary.

• 한국주조공학회지
• /
• 제31권5호
• /
• pp.243-248
• /
• 2011

Magnesium alloys have many advantages such as light-weight, high machinability, damping capacity, etc. So magnesium alloy parts have been used in transportation, mobile phone, military industries. Because of HCP atomic structure, Magnesium is very difficult in plastic deformation process, so most of magnesium products are fabricated by casting process. Magnesium alloys have low heat-capacity, high fluidity and low Fe solubility. For these reasons it is more suitable than aluminum in mass-production by casting. And various casting technologies have been developed. So casting technologies for magnesium developed recently is discussed in this paper.

• 한국주조공학회지
• /
• 제25권3호
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• 한국주조공학회지
• /
• 제29권3호
• /
• pp.138-143
• /
• 2009

Vacuum suction is applied to the mold during pouring in the inclined gravity die casting to remove defects such as misrun and gas porosity in the brake master cylinder. Casting defects are observed after solidification and their cause is analyzed by using the calculated results with commercial solidification and flow analysis code(ZCAST). The optimum vacuum suction is -2 cmHg, and when the start time of vacuum suction is 3 seconds after pouring, better filled result is obtained by holding it for 15 seconds. Reproducibility test under the optimum conditions attained from the above pouring tests is performed, and it is confirmed that these pouring conditions can be applied to the mass production immediately.

• 한국주조공학회지
• /
• 제34권5호
• /
• pp.151-155
• /
• 2014

The relatively low conductivity of conventional Mg-Al alloys often limits their areas of application. Therefore, several attempts to develop new high-conductivity magnesium alloys have been made recently. In this research, A Ce-rich rare-earth (RE)material and zinc were added to magnesium which contained no aluminum. As the RE and Zn content were increased, both the hardness and tensile strength were gradually increased, despite the fact that the electrical conductivity decreased slightly. The effects of an aging treatment on the conductivity and mechanical properties of Mg-RE-Zn alloys were also investigated. The electrical conductivity did not change according to the heat treatment conditions; however, the mechanical properties could be enhanced by proper aging heat treatments.

• 한국주조공학회지
• /
• 제39권5호
• /
• pp.94-101
• /
• 2019

This study investigated the microstructure properties of A356 and AC8A alloys with a rheocasting mold using an inclined cooling plate. In addition, a formability evaluation was performed according to the solid fraction. Regardless of the position, the overall microstructure was shown to be uniform and a finer crystal structure was obtained as the solid fraction increased. The study confirmed that the molding pattern changed according to the solid fraction and that the spherical α-Al and eutectic α were identified. The results of the formability according to the solid fraction of A356 and AC8A alloys were similar to the simulation results.

• 한국주조공학회지
• /
• 제43권6호
• /
• pp.294-301
• /
• 2023

The effects of Cu on feeding and macro-porosity characteristics were investigated in hypo- (A356 and 319) and hypereutectic (391) aluminum-silicon alloys. T-section and Tatur tests showed that the feeding and macro-porosity characteristics were significantly different between the hypo- and hypereutectic alloys. The hole and the pipe in the T-section and the Tatur casting in hypereutectic alloy showed a rough and irregular shape due to the faceted growth of the primary silicon, while the results of the hypoeutectic alloys exhibited a rather smooth surface. However, the addition of Cu did not strongly affect the macro-feeding behavior. It is known that copper segregates and interferes the feeding process in the last stage of solidification, possibly leading to form more amount of micro shrinkage porosity by the addition of Cu. The macro porosity formation mechanism and feeding properties were discussed upon T-section and Tatur tests together with an alloying addition.