• Journal of the Korean Ceramic Society
• /
• v.41 no.9
• /
• pp.647-652
• /
• 2004

In aqueous tape casting of alumina slurry systems, the relationships between the suspension compositions and the defects of the dried tapes were discussed. The suspensions compositions were controlled with the ratios of the solids, water and organics binder contents. The effects of the thickness of dried tape and kinds of binder system were also examined. In the defect free region, the apparent viscosity showed nearly same value due to the count balancing effect of solid and organic binder content on the apparent viscosity. When water content was constant, increasing solid led to decrease of organic binder content. The defect free region was narrowed with increasing of casting thickness. When linear type acrylic emulsion binders system (D1000 and D 1035) were used, defect free zone formed the belt type in the triangle of solid, water and organic binder content according to the line of constant water contents. However the defect free region was not found in the cross-link type emulsion binder system (D 1050).

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.220-224
• /
• 1999

Sliding wear test was employed to determine the effect of whisker content and orientation on the firiction and wear behavior of SiC whisker reinforced alumina. Composites containing unidirectionally oriented whiskers were prepared by a modified tape casting followed by lamination, binder removal and hot pressing in order to align the whiskers in the tape casting direction. Wear coefficients on three directions were measured; parallel and normal to the tape casting direction on the tape casting surface and normal to lamination direction on surfnce normal to the tape casting direction. In the effect of whisker orientation, the highest wear rate was obtained in the direction parallel tape casting direction and the lowest in the direction normal to lamination direction at all temperatures. Silicon oxide layer amoothing the surface was detected by energy dispersive X-ray analysis on the worn surface.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.2
• /
• pp.125-132
• /
• 2004

Statements of problem: All ceramic fixed partial denture cores can be made by the slip casting method and the advanced alumina tape method. The fracture resistance of these core connector areas is relatively low. Purpose: The purpose of this study is to standardize the appropriate volumetric figure and location of the connectors in the alumina core fabricated in alumina tape to be used in fixed partial dentures by way of topology optimization. Material and method: A maxillary anterior three-unit bridge alumina core with teeth form and surrounding periodontal apparatus model was used to ultimately design the most structurally rigid form of the connector. Loadings from a $0^{\circ}$, $45^{\circ}$ and $60^{\circ}$ to the axis of each tooth were applied and analyzed with the 3-D finite element analysis method. Using the results from these experiments, the topology optimization was applied and the optimal reinforcement layout of connector was obtained and the detail shape in the fixed partial denture core was designed. Results: The modified prosthesis with the form of a bulk in the lower lingual surface of the connector in the event, reduced the stress concentration up to 20% in the 3-D FEA. Conclusion: The formation of a bulk in the lower lingual connector area of an alumina core for a fixed partial denture decreases the stress to a clinically favorable measure but does not harm the esthetic point of view. This result illustrates the possibility of clinical application of the modified form designed by the topology optimization method.

• Journal of Powder Materials
• /
• v.22 no.6
• /
• pp.438-442
• /
• 2015

Porous thick film of alumina which is fabricated by freeze tape casting using a camphene-camphor-acrylate vehicle. Alumina slurry is mixed above the melting point of the camphene-camphor solvent. Upon cooling, the camphene-camphor crystallizes from the solution as particle-free dendrites, with the $Al_2O_3$ powder and acrylate liquid in the interdendritic spaces. Subsequently, the acrylate liquid is solidified by photopolymerization to offer mechanical properties for handling. The microstructure of the porous alumina film is characterized for systems with different cooling rate around the melting temperature of camphor-camphene. The structure of the dendritic porosity is compared as a function of ratio of camphene-camphor solvent and acrylate content, and $Al_2O_3$ powder volume fraction in acrylate in terms of the dendrite arm width.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.6
• /
• pp.483-489
• /
• 2019

For machine learning techniques, a large amount of high-quality material property data should be accumulated. In this study, several data for an alumina tape casting process were produced with the variables of slurry viscosity, gap size, and coating speed. The alumina tapes were manufactured in the range of 1,000~6,000 cps for slurry viscosity, $300{\sim}1,000{\mu}m$ for gap size, and 0.5~2.0 m/min for coating speed. As a result, the lower the viscosity, coating speed, and gap size, the more pore-free tapes could be manufactured. The viscosity of the slurry limited the minimum thickness of the tape. Green sheets with high packing density were manufactured from the slurry of 100~6,000 cps slurry viscosity, coating speed of 0.5 m/min, and a $300{\sim}500{\mu}m$ gap size.

• Journal of the Korean Ceramic Society
• /
• v.40 no.7
• /
• pp.667-671
• /
• 2003

Tape cast laminar composites with alumina/zircon(reaction-bonded mullite/zirconia) as an inner layer and alumina/zirconia or mullite/zirconia as an outer layer have been fabricated by hot-pressing. The mechanical properties(hardness and Young's modulus) and microstructure of laminar composites were examined using a nanoindentation technique and Scanning Electron Microscopy (SEM), respectively. The indentation load-displacement curve revealed the existence of residual stress in laminar composites.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.1060-1066
• /
• 2001

Water-based alumina tapes for application of all-ceramic crowns were fabricated using PVP as binder that is biocompatible, highly soluble in solvents, and no residue leftafter firing. Tensile strength of alumina tapes was governed by binder/(binder+plasticizer)ratio. On the other hand, linear shrinkage and density were determined by alumina/(alumina+organic) ratio. Composite for all-ceramic crowns, prepared by infiltration of a glass into sintered porous alumina, showed high flexural strength which increased with increasing sintered density.

• 대한치과보철학회:학술대회논문집
• /
• 1999.11a
• /
• pp.31-31
• /
• 1999

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.484-489
• /
• 2002

Hot-pressure sintered laminar composites with alumina/zirconia or mullite/zirconia as an outer layer and alumina/zircon (resulting in reaction-bonded mullite/zirconia during sintering) as an inner layer were fabricated by tape casting and lamination. Various forms of crack were observed in sintered laminar composites, these cracks included channel cracks in the outer layer, transverse cracks in the inner layer and interface cracks debonding interlayer. Based on detailed microscopic observations, the cracks were attributed to thermal expansion mismatch between the oxides consisting of the each layer. In particular, the interlayer and transverse cracks were confirmed in the laminates consisted of the mullite/zirconia system as the outer layers, however, those cracks were not observed in the alumina/zirconia system used. In addition, the crack propagation did not exhibit same behavior in the two kinds of outer layer when the indentation load was applied.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.61-68
• /
• 1999

To analyze several defects and residual stress in sintering of layer structure materials, multiayer materials with TZP/SUS and ZT/SUS, and bilayer materials with porcelain/alumina and porcelain/Y-TZP were fabricated by sintering method. Multilayer materials prepared by pressureless sintering show the sintering defect such as warping, splitting, cracking originated from the difference of sintering shrinkage between each layer, which could be controlled by the adjustment of number and thickness in interlayer. In tape casting, a certain pressure given during sintering relaxed the sintering defects, specially warping. The residual stress in bilayer was examined with Vickers indentation method. A small tensile stress in porcelain/alumina and a large compressive stress in porcelain/Y-TZP were generated on the porcelain interface due to the thermal expansion mismatch, which affected the strength of bilayer materials. As a consequence, the sintering defects of multilayer materials and the residual stresses of bilayer materials were dominantly influenced on material design and starting material constants.