• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.391-395
• /
• 1992

In order to improve the compactness and uniformity in ceramic green body, we have developed dynamic CIP(Cold Isostatic Pressing) as a new forming method in which the CIP and the vibratory pressing were combined. In dynamic CIP, bulk density on alumina compacts was linearly increased with higher │Pmax-Pbias│and maximum pressure of dynamic-CIP was decreased over one-third of that of conventional CIP to obtain the same bulk density.

• 한국세라믹학회지
• /
• 제48권2호
• /
• pp.168-172
• /
• 2011

Alumina powder was added in a general porcelain (Backja) with clay, feldspar and quartz contents to promote the mullite ($3Al_2O_3{\cdot}2SiO_2$) generation in the porcelain. Low melting materials ($B_2O_3(450^{\circ}C)$, $MnO_3(940^{\circ}C)$, CuO($1080^{\circ}C$)) were doped at ~3 wt% to modify the sinterability of porcelain with a high alumina contents and promote the mullite generation. Green body was made by slip casting method with blended slurry and then, they were fired at $1280^{\circ}C$ for 1hr by a $2^{\circ}C/min$. Densifications of samples with high alumina contents (20~30 wt%) were impeded. As the doping contents of low melting materilas increased, the sinterability of samples was improved. The shrinkage rate and bulk density of samples were improved by doping with low melting materials. Mullite phase increased with increasing the low melting contents in the phase analyses. This means lots of alumina and quartz were transformed into mullite phase by low melting contents doping. In the results, high bending strength of samples with high alumina contents was accomplished by improving the densification and mullite generation in the porcelain.

• 한국세라믹학회지
• /
• 제29권6호
• /
• pp.419-430
• /
• 1992

Fabrication possibility of low-shrinkage alumina without oxidation and wetting agent was presented on the basis of observation about oxidation behavior, microstructure and physical characteristics of such reaction agents free Al2O3-Al system. The composition less than Al 10w/o where Al can act as a sintering agent for Al2O3 was excluded. Under the condition of present experiments oxidation of Al2O3-Al system was dependent not on holding time but mainly on oxidation temperature. In thes case of Al powder not comminuted effectively during powder mixing of Al2O3-Al, columnar structure which would act as a hindrance to the densification during sintering developed more during oxidation with higher Al contents, and which made the fabrication of low-shrinkage Al2O3 ceramics impossible. If Al powder was comminuted effectively due to co-mixed Al2O3 characteristics, densification was improved because of no columnar structure and made the fabrication of sintered body with -2.7% dimensional change and 81% relative density possible. As a result, it is possible to fabricate dense low-shrinkage Al2O3 ceramics without oxidation and wetting agent under conditions such as smaller particle size of Al, Al contents below 50v/o, higher green density of Al2O3-Al compact and the use of Al2O3 powder used for high-density ceramics.

• 한국기계가공학회지
• /
• 제10권1호
• /
• pp.73-79
• /
• 2011

In this study, coring with diamond core drill on the sintered $Al_2O_3$ ceramic plate were carried out with different coring conditions such as various cutting speed and feed rate to evaluate their effectiveness on the wearing behavior of diamond tool and coring quality. The wearing rate of diamond core drill were getting better with increasing cutting speed and feed rate but the quality of cored hole were getting worse as increasing cutting speed and feed rate.

• 한국세라믹학회지
• /
• 제35권4호
• /
• pp.406-412
• /
• 1998

The reaction bonded alumina ceramics was prepared through the addition of each SiC and ZrO2 powder to the mixture of Al metal powder and Al2O3 The mono sized (3mm) and biodal sized (3mm+5mm) balls were used in attrition milling of Al and starting powders. The milling efficiency of both cases was compared by the analysis of particle size and X-ray diffraction. After the forming and sintering of each powder batchs the weight gains dimensional changes and densities were determined. The specimens were investigated by X-ray diffraction analysis and scanning electron microscope. Bimodal sized balls had better milling effect than single ball size in the milling of Al powder. However in the milling which ceramic powders mono sized the green body during the reaction sintering at 1$600^{\circ}C$ for 5 hour was about 10% The densities attained the values of 92-98% theoretical. The SiC added specimen that was milled with 3mm ball media had 96% theoretical density and dense microstructure.

• 한국분말재료학회지
• /
• 제27권6호
• /
• pp.490-497
• /
• 2020

The 3D printing process provides a higher degree of freedom when designing ceramic parts than the conventional press forming process. However, the generation and growth of the microcracks induced during heat treatment is thought to be due to the occurrence of local tensile stress caused by the thermal decomposition of the binder inside the green body. In this study, an alumina columnar specimen, which is a representative ceramic material, is fabricated using the digital light process (DLP) 3D printing method. DTG analysis is performed to investigate the cause of the occurrence of microcracks by analyzing the debinding process in which microcracks are mainly generated. HDDA of epoxy acrylates, which is the main binder, rapidly debinded in the range of 200 to 500℃, and microcracks are observed because of real-time microscopic image observation. For mitigating the rapid debinding process of HDDA, other types of acrylates PETA, PUA, and MMA are added, and the effect of these additives on the debinding rate is investigated. By analyzing the DTG in the 25 to 300℃ region, it is confirmed that the PETA monomer and the PUA monomer can suppress the rapid decomposition rate of HDDA in this temperature range.

• 한국결정성장학회지
• /
• 제31권3호
• /
• pp.116-126
• /
• 2021

코디어라이트(Mg₂Al₄Si₅O₁₈) 하니컴 세라믹스의 대표적 응용분야는 자동차 배기가스 정화용 필터(diesel particulate filter(DPF))이다. 천연광물, 조공제, 유기바인더를 혼합한 슬러리를 압출하여 DPF용 하니컴 코디어라이트를 성형한 후 980~1450℃ 범위에서 소결하였다. 소결온도에 따른 결정상(indialite, cordierite, cristobalite, alumina, spinel, mullite, pro-enstatite)의 형성과정을 XRD Rietveld 정밀화법을 이용하여 정량분석 하였다. 동시에, 세라믹 에칭(etching) 방법으로 소결 시료 표면의 비정질상을 제거한 후 SEM/EDS법을 사용하여 결정상들의 형상과 조성을 확인하였다. 이들 결과로부터 DPF 하니컴에서 결정상 형성 과정을 명확히 밝힐 수 있었다. 또한, DPF 하니컴의 소결온도에 따른 열팽창계수(linear coefficient of thermal expansion, CTE) 변화를 분석하였고, 결정상의 정량분석결과를 바탕으로 계산된 CTE와 비교하였다. 소결된 DPF 하니컴 내의 결정상들이 CTE 특성에 미치는 영향을 고찰하였다.