• Bulletin of the Korean Chemical Society
• /
• v.31 no.6
• /
• pp.1628-1632
• /
• 2010

Porous ${\eta}-Al_2O_3$ was synthesized by modified sol-gel method using ionic liquid as a templating material. The addition of ionic liquid assisted to increase the surface area of alumina. However, the acidity of aluminas prepared with ionic liquids was hardly affected regardless the change of its structural properties. Among the ionic liquids used in this study, 1-butyl-3-methylimidazolium hexafluorophosphate ([Bmim][$PF_6$]) was the most effective ionic liquid to produce porous ${\eta}-Al_2O_3$ particles. The catalytic performance of these aluminas has been investigated in dehydration of methanol to produce dimethyl ether. The alumina prepared with [Bmim][$PF_6$] outperformed the other aluminas except ${\eta}-Al_2O_3$ without modification in this reaction.

• Journal of the Korean Ceramic Society
• /
• v.30 no.12
• /
• pp.1029-1038
• /
• 1993

The microstructures of aluminas, included of dissolved CaO as $\alpha$-alumina seeded pseudo-boehmite hydrosol was gelled in plaster mold and doped of MgO as dipping of calcines(120$0^{\circ}C$-2h) into Mg-nitrate solution, were compared to the one of which additives are excluded during the gellation. It was formed the boundary layer of 300~350${\mu}{\textrm}{m}$ distance from surface to the inside, containing of approximately 500ppm CaO by dissolved Ca from plaster mold. As the MgO addition to the boundary layer with dissolved CaO, the microstructure of the layer was uniformed and inhibited the grian growth, compared to one of that additives be excluded specimen and of MgO doped-inside region. This result was considered as abnormal grain growth and effect of flat boundary formation be appeared by effects of dissolved CaO, were decreased by MgO co-doping.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.6
• /
• pp.617-618
• /
• 1998

A simple and reproducible pretreatment method was developed for the determination of dioxins in milk sample. Liquid-liquid extraction (LLE) was used for the initial extraction of the analyte from milk. For the elimination of interferences coextracted from milk, acid treatment followed by multilayer silica gel, and then alumina column clean-up were performed. The clean extract could be obtained without carbon column or high performance liquid chromatographic (HPLC) clean-up procedure. Polychlorinated biphenyles (PCBs) and dioxins were separated on neutral alumina activated at 180 ℃ for 12 hours. The final extract was analyzed by HPLC and high resolution gas chromatography/high resolution mass spectrometry (HRGC/HRMS). The recovery of dioxins spiked in milk at 75-300 ppt level was 83.3-98.9% and their relative standard deviation was 4.1-14%.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.6
• /
• pp.619-624
• /
• 1998

A simple and reproducible pretreatment method was developed for the determination of dioxins in milk sample. Liquid-liquid extraction (LLE) was used for the initial extraction of the analyte from milk. For the elimination of interferences coextracted from milk, acid treatment followed by multilayer silica gel, and then alumina column clean-up were performed. The clean extract could be obtained without carbon column or high performance liquid chromatographic (HPLC) clean-up procedure. Polychlorinated biphenyles (PCBS) and dioxins were separated on neutral alumina activated at 180 ℃ for 12 hours. The final extract was analyzed by HPLC and high resolution gas chromatography/high resolution mass spectrometry (HRGC/HRMS). The recovery of dioxins spiked in milk at 75-300 ppt level was 83.3-98.9% and their relative standard deviation was 4.1-14%.

• Korean Journal of Crystallography
• /
• v.8 no.2
• /
• pp.89-96
• /
• 1997

In order to apply synthesis technique of the high purity ceramic powder to the traditional ceramic powder, mullite powder which is widly used for refractory materials was synthesized. Boehmite and Hadong kaolin with high alumina content were used as starting materials and gel coating method was tried to produce the mullite powder. As a result, the mullite powder of high quality was successfully obtained at 1350℃. The unreacted silica and cornudum were not observed in the synthesized mullite powder, mullite content was more than 80% when the starting materials were sintered at 1700℃. Their properties showed bulk specific gravity of 2.56, water absorption of 1.9%, and 3-point flexual strength of 169 MPa. It is thought that that their good properties are applicable to refractory materials of high quality.

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.325-330
• /
• 2007

High porous AlO(OH) gel is used in precursor of ceramic material, coating material and porous catalyst. For use of these, not only physiochemical control for particle morphology, pore characteristic and peptization but also studies of synthetic method for preparation of high porous AlO(OH) gel were required. In this study, high porous AlO(OH) gel was prepared through the aging and filtration process of aluminum hydroxides gel precipitated by the hydrolysis reaction of $Na_2CO_3$ solution and $Al_2(SO_4)_3$ and $Na_2SO_4$ mixed solution. In this process, optimum synthetic condition of AlO(OH) gel having excellent pore volume as studying the effect of hydrolysis pH on gel precipitates has been studied. Hydrolysis pH brought about numerous changes on crystal morphology, surface area, pore volume and pore size. Physiochemical properties of gel were investigated as using XRD, TEM, TG/DTA, FT-IR and $N_2$ BET method.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.864-871
• /
• 2004

Porous pseudo-boehmite gel was prepared through the aging process of amorphous aluminum hydroxides gel precipitated by the hydrolysis reaction of dilute NaOH solution and AlCl$_3$ solution. In this study, the synthesis method was studied on porous pseudo-boehmite gel having maximum pore volume, as being investigated the changes of crystal structure, infrared rays absorption spectrum, BET surface area and pore structure when the hydrolysis reaction is controlled in the range of pH 7.6~11.6 and the aging process is hold up for 2~24 h at 60~10$0^{\circ}C$. We could find that the gel precipitates deposited in in range of pH 7.6~9.6 were developed into porous pseudo-boehmite which surface area was 250~357 $m^2$/g, pore volume was 0.4~0.7 cc/g and average pore size was 58~l14$\AA$. However, the gel precipitates deposited in range of pH 10.6~11.6 were developed into bayerite which pore volume was very little.

• Membrane Journal
• /
• v.15 no.2
• /
• pp.105-113
• /
• 2005

Silica membranes were prepared on a porous metal sheet by ultrasonic spray pyrolysis method for gas separation at high temperatures. In order to improve the permselectivity, silica was deposited in the sol-gel derived $silica/\gamma-alumina$ intermediate layer by pyrolysis of tetraethyl orthosilicate (TEOS) at 873 K. The pyrolysis with forced cross flow through the porous wall of the support was very effective in plugging mesopores, Knudsen diffusion regime, that were left unplugged in the membranes. At permeation temperature of 523 K, the silica/alumina composite membrane showed $H_2/N_2$ and water/methanol selectivity as high as 17 and 16, respectively, by molecular sieve effect.

• Journal of the Korean Ceramic Society
• /
• v.28 no.2
• /
• pp.153-159
• /
• 1991

Polymeric alumina sol and polymeric silica sol were synthesized from aluminum sec-butoxide and tetraethyl orthosilicate, respectively as starting materials. A clear mullite sol was obtained by mixing these sols. When the mullite sol had a proper viscosity which was dependent on drying time, the fibers were fabricated by spinning. The optimum viscosity for fabrication of mullite fibers was 103-104 cps, and the fibers with various sizeswere made using the sols. The mullite was a major phase of the calcined fibers and the diameters of the fibers were about 50$\mu\textrm{m}$.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.69-73
• /
• 1994

Si3N4 ceramics could be densified above 3.2g/㎤ with pressureless sintering at below 178$0^{\circ}C$ by coating Si3N4 and Y2O3 powder with an alumina sol. Substitution a portion of Al2O3 with AlN improved densification. Additional milling of the coated powder in large improvement in bending strength greater than 800 MPa (4-point).