• 환경위생공학
• /
• 제16권3호
• /
• pp.104-110
• /
• 2001

NOx coming from combustion make photochemical smog and acid rain, cause chronic respiratory disease resulting in critical hazard to environment and human health. Most composition of NOx coming from combustion is NO and the remaining small amount of $NO_x$ is $NO_2$. Currently, many technologies are developed and used to control NO release. One of these technologies is control technology through use of the adsorbent. In this study, two methods were used to make the adsorbent and compared. KOH and ${\gamma}{\;}-alumina$ were mixed by using two methods. Then, the experimental conditions were as follows: the concentrations of KOH used were 1 mole, 0.5 mole, and 0.1 mole, respectively and the amount of ${\gamma}{\;}-alumina$$250^{\circ}C$. As a result, precipitation method, which is one of the production methods of the adsorbent, showed the most removal efficiency as KOH concentration as 1 mole and reaction temperature as $100^{\circ}C$ were used. This study shows 40 to 60% of micropores of ${\gamma}{\;}-alumina$ was lost by the reaction with KOH through the analysis of SEM and BET Finally, KOH is the most predominant factor to control the removal of NO rather than micropore of the adsorbent.

• 멤브레인
• /
• 제21권3호
• /
• pp.229-235
• /
• 2011

본 연구에서는 메조기공 티타니아/알루미나 막을 솔-젤법을 이용하여 제조하였다. 티타니아/알루미나 막의 기공구조 및 결정상은 하소 온도에 따라 조절될 수 있었다. 티타니아에 알루미나를 첨가하는 것은 티타니아 결정상이 아나타제상에서 루타일상으로 상변화 되는 것을 지연시켜 기공구조의 열적 안정화를 가져왔다. 5번 딥코팅하여 제조된 막의 두께는 $10.3{\mu}m$였으며, 평균 기공크기는 5 nm이었다. 기체 투과 실험 결과는 수소와 질소의 permeance는 각각 $17.1{\tiems}10^{-7}mol/m^2{\cdot}s{\cdot}Pa$ 및 $4.7{\tiems}10^{-7}mol/m^2{\cdot}s{\cdot}Pa$이었다. 이 결과는 Knudsen 확산에 의해 설명될 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.254-257
• /
• 2008

For crystalline slags, of which the viscosity rapidly increases at $T_{cv}$ due to the formation of crystalline phases, the Tcv is affected by measurement conditions. In this study, we investigated the effect of cooling rate, and alumina dissolution on the determination of $T_{cv}$. Using synthetic slag samples based on the composition of Alaska Usibelli slag, $T_{cv}$ were determined under a constant cooling rate of $2^{\circ}C$/min, and under rapid cooling with holding time to allow the slag to reach thermal and rheological equilibrium. The effect of alumina dissolution was investigated using platinum lined crucibles. The constant cooling resulted in lower $T_{cv}$ by $33^{\circ}C$ as compared to the equilibrium measurements. Under $2^{\circ}C$/min cooling, the blocking alumina dissolution resulted in lower $T_{cv}$ by $23^{\circ}C$. When the $T_{cv}$ was measured under $2^{\circ}C$/min cooling using an alumina crucible, therefore, the effects of a constant cooling is somewhat offset by the alumina dissolution effect, and bring the measured value closer to the true value.

• 한국재료학회지
• /
• 제9권1호
• /
• pp.35-41
• /
• 1999

In this study we investigated the effects of process variables on the bond strength, and its dependency upon the interfacial chemistry when the joined $ZrO_2$ toughened $Na\beta$"-alumina to $\alpha$-alumina using B$_2$$O_3$-$SiO_2$-Al$_2$$O_3$-CaO glass sealant. We observed that bond strength is mainly determined by the strength of the glass, which, in turn, depends on the glass composition established after joining reaction. Joining at $950^{\circ}C$ for 15min yielded the highest average bond strength of 66MPa. Different types of interfacial reaction seem to occur at each interface. After joining at $950^{\circ}C$ for 15min we found that Ca and Si diffuse much deeper(~15$\mu\textrm{m}$) into the $\beta$"-alumina composite than into the $\alpha$-alumina(<1$\mu\textrm{m}$) as a result of ion exchange reaction and more effective grain boundary diffusion. Thermal expansion coefficient of the glass was found to have changed more closely to those of the $\beta$"-alumina composite and $\alpha$-alumina, which put the glass under a slight compressive stress.ressive stress.

• 한국세라믹학회지
• /
• 제30권5호
• /
• pp.347-356
• /
• 1993

In joining alumina ceramics to metal by using Mo-Mn metallizing process the effects of metallizing thickness, temperature, and the composition of paste on the bond strength and the microstructure of joining interface were investigated. The bond strength variation in the range of metallizing temperature, 1350~155$0^{\circ}C$ was more than 150MPa above 145$0^{\circ}C$ and the optimum metallizing thickness was 30${\mu}{\textrm}{m}$. The optimum contents of Mn in Mo-Mn paste was 5% due to the bond strength decrease with the increase of addition. The effect of SiO2 addition in paste on bond strength was saturated around 200MPa. It was also observed that as the particle size of Mo decreased, the joinning with higher bond strength was shown in spite of low metallizing temperature.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.295-300
• /
• 2009

The crystal structure of surface coatings on Al1050 alloy by PEO (Plasma Electrolytic Oxidation), were investigated. The electrolyte for PEO was Na-Si-P system solution. The main crystalline phase were $\gamma$-alumina and $\alpha$-alumina. Crystallinity was increased with applied voltage and applied time. The dominant crystalline phase were affected not only chemical composition of Al alloy substrate and electrolyte, but also the +/- ratio of applied voltage.

• 한국세라믹학회지
• /
• 제41권9호
• /
• pp.647-652
• /
• 2004

In aqueous tape casting of alumina slurry systems, the relationships between the suspension compositions and the defects of the dried tapes were discussed. The suspensions compositions were controlled with the ratios of the solids, water and organics binder contents. The effects of the thickness of dried tape and kinds of binder system were also examined. In the defect free region, the apparent viscosity showed nearly same value due to the count balancing effect of solid and organic binder content on the apparent viscosity. When water content was constant, increasing solid led to decrease of organic binder content. The defect free region was narrowed with increasing of casting thickness. When linear type acrylic emulsion binders system (D1000 and D 1035) were used, defect free zone formed the belt type in the triangle of solid, water and organic binder content according to the line of constant water contents. However the defect free region was not found in the cross-link type emulsion binder system (D 1050).

• 한국세라믹학회지
• /
• 제22권6호
• /
• pp.58-70
• /
• 1985

The bond strength of metal to ceramic sealing in Mo-Mn metallizing was investigated by examining the effects of flux composition in alumina ceramics particle size of molybdenum metal powder wet hydrogen atmosphere and temperature in metallizing. The maximum bond strength was obtained when the glass phase filled almost all the microstructural cavities around the interfacial area with few micropores. Such a favorable microstrcutre waas formed and maximum bond strength was observed between 130$0^{\circ}C$. Also the metal to ceramic bond strength was increased using finer molybdenum metal powder than coarse powder. When content of $SiO_2$ in the flux of alumina ceramics was constant metal to ceramic bond strength was improved with increasing the ratio of CaO to MgO in the flux.

• 전기학회논문지
• /
• 제67권11호
• /
• pp.1463-1470
• /
• 2018

In this study, 20 types of samples were prepared by mixing different kinds of inorganic materials to develop insulation materials for epoxy - based GIS substation equipment used under high voltage environmentally friendly insulation gas. One of the electrical characteristics, AC insulation breakdown experiment was performed. As mixing ratio of mixed heterogeneous inorganic materials, the dielectric breakdown strength was increased with increasing filler ratio of micro silica, micro silica : micro Alumina, 1:9, 3:7, 5:5, 7:3, 9:1, and decreased as the filling amount of micro alumina increased. The AC insulation breakdown characteristics were the best when the composition ratio was 9:1. The higher the content of silica, the better the interfacial properties, and the larger the alumina content ratio, the worse the interfacial properties.

• Bulletin of the Korean Chemical Society
• /
• 제27권8호
• /
• pp.1159-1163
• /
• 2006

Aluminum nanotube has been fabricated by a physical vapor deposition/atmospheric pressure injection using an anodic porous alumina film as a template. The pore external-, and inside diameters and the length of the aluminum nanotubes fabricated by this method are 60 nm, 35 nm and 2 $\mu$m, respectively. The structure of the fabricated aluminum nanotubes was examined by a kind of chemical treatment as extraction of copper on the cross-sectional area of these aluminum tubes in a mixed solution of $CuCl_2$ and HCl by difference of ionization tendency between aluminum and copper. The composition of the aluminum nanotube was identified by the two dimensional Hybrid Plasma Equipment Model (HPEM) employing the inductively coupled plasma.