• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1269-1270
• /
• 2006

Mg-Zn-RE alloys had a novel lond period stacking ordered (LPO) structure. Their rapidly solidified powder metallurgy (RS P/M) alloys exhibited a combination of high strength and god ductility (tensile yield strength above 550 MPa and elongation above 5%). The LPO Mg-Zn-RE RS P/M alloys had high elevated temperature strength (tensile yield strength above 380 MPa at 473 K) and exhibited a high-strain-rate superplasticity at higher temperatures. In Japan, a national project for developing high strength LPO Mg-Zn-RE RS P/M alloys has started at 2003 for 5 years, which is founded by the Ministry of Economy, Trade and Industry (METI) of Japan. In the national project, project targets in materials performances have been achieved. The developed LPO Mg-Zn-RE RS P/M alloys exhibited higher tensile yield strength, fatigue strength and corrosion resistance than high strength aluminum alloys of extra-super-duralumin (7075-T6).

• Journal of Korea Foundry Society
• /
• v.20 no.1
• /
• pp.3-12
• /
• 2000

The lead content of drinking water has been restricted to less than 15 ppb by Environmental Protection Agency (EPA) in USA. This has led to extensive research and development work at the Materials Technology Laboratory (MTL) of CANMET, a Canadian Government research laboratory, on the development of low-lead and lead-free copper alloys for plumbing applications. Attentionhas also been focused on the environmentally friendly and energy efficient permanent mold casting process to minimize the disposal of foundry sand contaminated by lead due to the use of leaded alloys in the non-ferrous foundries. A new series of alloys called SeBiLOY contaning Bi and Se been introduced to replace lead in the leaded alloys. This paper addresses some important casting characteristics such as fluidity, hot tear resistance, mechanical properties and microstructure of lead-free alloys such as SeBiLOY III and low-lead alloys such as silicon brass, silicon bronze and yellow brass in gravity permanent mold casting.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.4
• /
• pp.205-212
• /
• 2008

Characteristics of microstructures, mechanical properties and formability of two Al-20Si-5Fe-2Ni alloys produced by gas atomizing (P/M) and spray forming (S/F) respectively were compared at temperatures up to $560^{\circ}C$. Room temperature hardness values and tensile strengths of both alloys were increased in accordance with temperature after heat treatment above $300^{\circ}C$. The highest values of hardness and tensile strength of both alloys were obtained at $490^{\circ}C$. It was interpreted that increase in hardness and tensile strength according to heating temperature between $300{\sim}490^{\circ}C$ was mainly related to increase in internal stress between Al matrix and reprecipitated particles. S/F alloys showed better formability and wear property than P/M alloys due to the homogenity of microstructures above $300^{\circ}C$.

• Journal of Technologic Dentistry
• /
• v.8 no.1
• /
• pp.45-50
• /
• 1986

This study investigated the effect of burnout temperature on the castability of some nickelchromium alloys for porcelain fused to metal system and the effect of beryllium on the castability. Four alloys were evaluated: two contained beryllium(rexillium III, Super I) and two nonberyllium(Unibond, NNB). five burnout temperature, ranging form 100$^{\circ}F$ to 1800$^{\circ}F$, were aet at 200$^{\circ}F$ intervals for this study. The results obtained were as follows: 1. Beryllium-containing alloys were more castable than nonberyllium-containing alloys. 2. There was an optimal burnout temperature of range from 1400$^{\circ}F$ to 1600$^{\circ}F$ for the berylliumcontaining alloys studied. 3. An optimal burnout temperature for the nonberyllium alloys was not established.

• Corrosion Science and Technology
• /
• v.22 no.5
• /
• pp.305-313
• /
• 2023

The objective of this study was to investigate the effectiveness of sodium dodecyl benzene sulfonate (SDBS) as a corrosion inhibitor on the pitting corrosion behavior of aluminum alloys used in electric vehicle battery cooling systems within a mixture of ethylene glycol and water (EG-W) coolant. Potentiodynamic polarization testing revealed unstable passive film formation on the aluminum alloys in the absence of SDBS. However, the addition of SDBS resulted in a robust passive film, enhancing the pitting corrosion resistance across all examined alloys. Pitting corrosion was predominantly observed near intermetallic compounds in the presence of Cl? ions, which was attributed to galvanic interactions. Among tested alloys, A1040 demonstrated superior resistance due to its lower areal fraction of precipitates and donor density. The incorporation of SDBS inhibitors mitigated the overall pitting corrosion process by hindering Cl? ion penetration. These findings suggest that SDBS can significantly improve pitting corrosion resistance in aluminum alloys employed in battery coolant environments.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.2
• /
• pp.75-86
• /
• 2001

In this paper it has been compared briefly the hydrogen storage using hydrogen storage alloys with other technologies and introduced the general properties of hydrogen storage alloys. The recent research trends and activities related to hydrogen storage alloys were given here.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.276-281
• /
• 2005

We have investigated the effects of an external magnetic field on the growth direction and the grain size of electrochemically prepared CoPtP alloys. Electrodeposited CoPtP alloys were synthesized by appling an external magnetic field with 0 to 1 T to the perpendicular direction of the films. In the electrodeposited CoPtP alloys without external magnetic field, the growth direction of the alloys was mixed by fcc (111) and hop (002), but only hop (002) was observed in the alloys with 1 T external magnetic field. CoPtP alloys were grown as the columnar growth and the grain size increases with growing the alloys. With appling an external field, the grain size of the alloys was controlled less than 20 nm which is smaller than single domain of Co, and the easy axis of alloys, hcp (002) direction, was grown perpendicular to the films up to 200 nm. We could obtain the optimal thickness of the alloys and electrodeposition condition from the above results. Coercivity and squareness of CoPtP alloys taken out-of-plane are 6.1 kOe and 0.9, respectively. The magnetic properties of CoPtP alloys were measured by VSM, and the microstructural characterization and crystalline orientation measurement of the alloys were carried out by TEM and XRD.

• Journal of Korea Foundry Society
• /
• v.26 no.3
• /
• pp.123-128
• /
• 2006

Mechanical and thermal properties of spray-cast hypereutectic Al-20wt.%Si-xwt.%Fe alloys (x=0, 1, 3, 5) were investigated. After the spray-casting, hot extrusion was performed at $400^{\circ}C$. Intermetallic compound (${\beta}-Al_5FeSi$) and primary Si are observed in the spray-cast aluminum alloys. The size of primary Si and intermetallic compound of the spray-aluminum alloys became finer and more uniformly distributed than that of the permanent mold cast ones. Ultimate tensile strength of the spray-cast aluminum alloys increased by increasing Fe contents, but that of the permanent mold cast aluminum alloys decreased by increasing Fe contents possibly due to increased amount of coarse intermatallic compound. The coefficient of thermal expansion (CTEs) of the aluminum alloys became lower with finer primary Si and intermetallic compound, and this is attributed to the increased amount of interfacial area between the aluminum matrix and the phases of finer Si and intermetallic compound.

• Korean Journal of Materials Research
• /
• v.24 no.4
• /
• pp.175-179
• /
• 2014

Ti and Ti alloys have been extensively used in the medical and dental fields because of their good corrosion resistance, high strength to density ratio and especially, their low elastic modulus compared to other metallic materials. Recent trends in biomaterials research have focused on development of metallic alloys with elastic modulus similar to natural bone, however, many candidate materials also contain toxic elements that would be biologically harmful. In this study, new Ti based alloys which do not contain the toxic metallic components were developed using a theoretical method (DV-$X{\alpha}$). In addition, alloys were developed with improved mechanical properties and corrosion resistance. Ternary Ti-Ag-Zr alloys consisting of biocompatible alloying elements were produced to investigate the alloying effect on microstructure, corrosion resistance, mechanical properties and biocompatibility. The effects of various contents of Zr on the mechanical properties and biocompatibility were compared. The alloys exhibited higher strength and corrosion resistance than pure Ti, had antibacterial properties, and were not observed to be cytotoxic. Of the designed alloys' mechanical properties and biocompatibility, the Ti-3Ag-0.5Zr alloy had the best results.

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.184-193
• /
• 1997

Aluminium and aluminium alloys have the high electrical and heat conductivity. It gives rise to difficulties for a choice of electrodes material for their contact electric welding. This paper describes the investigations performed to solve the above problem. The purpose of this investigation was to obtain dispersion-hardening alloys by the internal oxidation method, to optimize their contents and treatment modes, to produce electrodes of these alloys and to test them. The strengthing effect of alloys with oxide particles depends on their size stability at high temperatures. Despite of the fact, that oxides are the most stable of all the non-metallic phases their coagulation takes place. Based on the early results, we chose two types of alloys, first No. 1 Cu - 0,4%Al and second No. 2 Cu - 0,2%Be for production of electrodes. These alloys had not additional alloying elements. These alloys were prepared as 1 mm plates and flake-formed 200 m thick, and also No. 1 as a powder of size 100 mkm (received from Korea). The large samples for electrodes were produced by three methods : explosive welding method, dynamic one including the explosion compression of electrode blank and the quasi-dynamic method including the high-speed compression of dense briquest and the further hot extrusion of a rod.