• 한국주조공학회지
• /
• 제18권6호
• /
• pp.593-603
• /
• 1998

Commercial ductile iron was coated with titanium and aluminum powders by low pressure plasma spraying and then irradiated with a $CO_2$ laser to produce anti-corrosive TiC composite layer. TiC carbides were precipitated homogeneously in a laser alloyed layer by in-situ reaction between carbon existed in the base metal and titanium with thermal sprayed coating. The formation of gas pores and brittle limited mixing zone with ledeburite microstructure in TiC composite layer were surpressed by the complementary alloying of aluminum. The hardness of TiC composite layer obtained by addition of titanium and aluminum was between 600 and 660 Hv, which was three times as high as the hardness of ferritic ductile iron. From the results of isothermal oxidation at 1123k for 24 hours in air, high temperature oxidation resistance of the TiC composite layer with aluminum was improved and doubled when compared with the TiC composite layer without aluminum.

• 한국표면공학회지
• /
• 제29권4호
• /
• pp.278-285
• /
• 1996

The structure of coating layer formed by hot dip Al-Cu alloy coating on Monel 1400 metal was studied. The coating layer consists of alloyed layer adjacent to the Monel 400 substrate and Al-Cu alloy. It was found that the hardness of coating increased with dipping time and heat treatment associated with the diffusion and the formation of intermetallic compound at the interface. However the thickness of coating layer was decreased at high dipping temperature due to tile higher viscosity of liquid coating alloy. Diffusion heat treatment at $600^{\circ}C$ after coating resulted in the disappearence of adhered Al(Cu) and $CuAl_2$ phases, and then they transformed into the new phases of CuAl and Al7Cu4Ni at coating layer.

• 보존과학연구
• /
• 통권14호
• /
• pp.45-76
• /
• 1993

Au-Cu alloyed coating layer were found by Hg-amalgam process and it seemed to be used Cu-amalgam process similar to Au-amalgam. Coated layer is dense and unique, Thickness of layer was 1.5 to $18.0\mum$ which had 95.3 to 99.8% purity of gold Matrix metal mostly cosists of forged copper alloy which had high purity and ferrite ($\alpha$) strusture. It showed excellent refining technical level at that time. Aowever, the nail, ferrous matrix used for strength needed, composed of silver foil packed and gold layer for adherence between ferrous matrix and gold layer

• 한국레이저가공학회지
• /
• 제2권2호
• /
• pp.27-33
• /
• 1999

Electron beam was applied on the low carbon steel in order to fabricate Metal/Metal GBM(Graded Boundary Material). Ni sheet was placed on the steel substrate. The electron beam was irradiated on the surface and produced a homogeous alloyed layer. Sequential repetition of electron beam treatments for 4 times resulted in 8mm thick graded layer. To determine each layers property, optical microscopy, XRD, microhardness tester and EDS were used. The residual stress was measured by the low angle x-ray diffraction method. The graded boundary layer was stepwise profile, but Ni content incresed up to 80 wt% and Fe content decreased 20 wt% near surface. Each layers microstructure and hardness varied by different Fe/Ni composition. The compressive residual stress was induced by martensite transformation in the 1st and End layers and the shrinkage cracks were formed in graded layer by rapid cooling.

• 한국주조공학회지
• /
• 제25권4호
• /
• pp.161-167
• /
• 2005

The experiment of hot dip interaction tests was carried out in order to study the formation behavior of interfacial reaction layer between as-received STD61 hot work tool steel and a commercial pure aluminum melt, Al-xwt.%Fe(x=0.2, 0.5, 0.8 and 1.1) alloys melt and Al-xwt.%Si(x=1.0, 4.0, 7.0 and 10.0) alloys melt, respectively. The results show that the reaction layer, over 300 ${\mu}m$ in thickness, is easily formed by the dissolution of silicon from as-received tool steel. When the iron content in the aluminum alloy is higher than 1.1 wt.%, the thickness of reaction layer decreases below 180 ${\mu}m$ by preventing iron dissolution from the tool steel. The silicon dissolved from tool steel acts as a strong promoter on the formation of reaction layer, but the alloyed silicon in molten aluminum alloys acts as an inhibitor on the formation of reaction layer.

• 한국표면공학회지
• /
• 제27권5호
• /
• pp.303-311
• /
• 1994

In this study, the factors, such as coating temperature T(K), reaction time t(sec) and mobile carbon content $C^*$ (wt%) of steels affecting, the growth rate of carbide layer were investigated in the reactive deposition and diffusion coating using the fluidized bed. From the results, the coating thickness d(cm) can be expressed by an equation. d=$C^*$$(KT)^{1/2}$, where K=K$\circ$exp(~Q/RT), KTEX>$\circ$ = 1.4$\times$$10^{-2}cm^{-2}$/sec, and Q=46Kcal/ mol. It was in a good aggrement with the experimental results, reguardless of the diffusion coating method and the carbide layer. Therefore, if the mobile carbon content of carbon steels and alloyed steels is known, the thickness under coating conditions can be predicted from the previous equation.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.41-44
• /
• 1996

고하중, 저속에서의 마찰마모특징을 나타내는 건설기계의 작업장치 연결부의 핀/부싱 조인트의 개발 적용성 검토를 위해 기존의 사용방법인 표면경화처리 후 그리이스 급유하는 경우와 ESA(전기방전코팅)처리후 고체윤활제를 도포한 경우의 마찰마모특징을 시험 분석하여 기존 방법보다 ESA처리후 고체윤활제를 도포하는 경우의 마찰마모 특성이 매우 우수한 적을 확인하였다.

• 분석과학
• /
• 제6권2호
• /
• pp.197-205
• /
• 1993

닉켈과 크롬 20% 혼합분말을 실험실용 아트리터에서 시간을 달리하여 밀링하였고 입도분포, 미세조직 및 X-레이 회절 특성을 조사하였다. 합금화 상태를 확인하고자 포화자화값과 보자력값을 측정하였고 플라즈마 용해 잉곳 경우와 비교하였다. 기계적 합금화는 분말의 미세화 단계 후 크롬이 닉켈 속으로 확산이 일어나는 계면적의 증가에 의해서 진행하였다. 그러나 15시간 이상 밀링 후 서브 미크론 크기의 결정립으로 정상상태가 이루어졌음에도 불구하고 용해 잉곳과 같이 조성적으로 균일한 고용합금의 자성특성이 관찰되지 않았다. 밀링 시간이 길어질수록 결정립의 크기는 미세화되었으며 합금층이 증가하였다. 따라서 조성의 균질화는 분말의 소성변형에 의해서 일어나는 성분분말 사이의 계면적 증가와 계면내에서 입계 또는 전위와 같은 격자결함을 통해 크롬의 닉켈 속으로 확산에 의해서 율속되는 것으로 생각된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.391-394
• /
• 2002

There has recently been much interest and research in developing digital x-ray systems based on using amorphous selenium(a-Se) photoconductors as the image receptor. The amorphous selenium layer that is currently being studied for use as an x-ray photoconductor is not pure a-Se but rather amorphous selenium alloyed with arsenic. We fabricated samples using the selenium and arsenic alloy with various concentrations of the arsenic. In this work, x-ray photoconductor using amorphous selenium alloyed with arsenic were fabricated with different concentrations of the arsenic (0.1 wt.%, 0.3wt.%, 0.5wt.%, 1wt.%, 1.5wt.%, 3wt.%, 5wt.%). The seven kind of samples was fabricated with a-Se alloyed with arsenic through vacuum thermal evaporation. We also investigate the arsenic concentration dependence on the device performance in radiation detector. The electric characteristics of radiation detector devices with changing additive ratio of the arsenic is performed by measuring the x-ray induced photocurrent and integrating it over time to find the total charge. The thickness of a-Se is $100{\mu}m$. Bias voltages $3V/{\mu}m$, $6V/{\mu}m$， $9V/{\mu}m$ are applied at the samples. As results, the net charge of a-Se 0.3% As sample is $526.0pC/mR/cm^2$ at $9V/{\mu}m$ bias. The net charge is decreased as with the increasing additive ratio of arsenic.

• 열처리공학회지
• /
• 제8권1호
• /
• pp.32-43
• /
• 1995

Ti-6Al-4V alloy are widely used in chemical and aircraft industries for their good corrosion resistance and high strength to weight ratio. Surface alloying of Ti alloy by $CO_2$ laser is able to produce few hundred micrometers thick TiN surface-alloyed layer with high hardness on the substrate very simplely by injecting reaction gas($N_2$) into a laser-generated melt pool and adjust the hardness to the specific requirements of the individual application by changing of laser processing parameters. This research has been investigated the effect of such parameters on TiN surface-alloying of Ti-6Al-4V alloy by $CO_2$ laser. The maximum hardness of TiN surface-alloyed zone waw obtained by injecting 100% $N_2$ gas and it was decreased as the amount of $N_2$ gas in Ar and $N_2$ gas mixture was decreased. As scanning speed was increased, the hardness and depth of TiN surface-alloyed zone was decreased at constant laser power. The surface hardness after double scanning laser treatment is higher than that of single scanning. At constant laser power, the surface roughness is increased after the surface alloying if laser scanning speed is decreased.