• 플랜트 저널
• /
• 제8권2호
• /
• pp.52-58
• /
• 2012

Pipe means the connection of the tube in order to transfer fluid from one device to another device. The piping stress analysis is to analyze the structural stability considering the location and the features of piping support after completing the piping design, The allowable stresses comply with the requirements of the relevant standards by examining whether the support of the function and location of pipe or re-operation is confirmed. Allowable stresses are to make sure that the maximum stress should not exceed the allowable stress presented in the ASME B31.1 POWER PIPING code. ASME B31.1 POWER PIPING code ensures a smooth stress analysis can be performed during the initial pipe stress analysis as provided in the case of straight pipe to the horizontal distance between the supports. However, because there is no criteria set in the case of curved pipe, the optimum pipe supporting points were studied in this paper. As mentioned about the curved pipe, loads applied to the support of the position of 17% and 83% of the position relative to the elbow part have results similar to the load acting on the support of straight pipe.

• Journal of Biosystems Engineering
• /
• 제14권3호
• /
• pp.207-214
• /
• 1989

In this study, impact force and angular displacement of the pendulum were measured by the load cell and potentiometer. Mechanical behavior of rough rice under impact loading was able to analyze precisely and efficiently, because measured data were accumulated and handled by the automatic data acquisition system making use of microcomputer system. Impact force and angular displacement were measured with a resolutiln of 1/1500 seconds in time. Mechanical behavior such as force and energy at rupture point of Japonica type and Indica type rough rice were measured with this system. After impact loading, the damage of rough rice was examined with the microphotograph and an allowable impact force was measured. The results obtained in this study are summarized as follows. 1. Machanical behavior of rough rice under impact loading was analyzed precisely and efficiently because measured data were accumulated and handled by this data acquisition system. 2. Rupture force and rupture energy of rough rice were appeared to be the lowest value in the range of 16 to 18 % moisture content, and rupture force and rupture energy of Japonica type were higher than those of Indica type in each level of moisture content. 3. From the result of the damage examined after the impact loading, allowable impact force was the lowest in the range of 16 to 18 % moisture content, and the value of the allowable impact force of Japonica type was higher than that of Indica type in each level of moisture content.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.859-864
• /
• 2015

This paper analyzes the impact of Plug-in Electric vehicles(PEVs) on power demand and voltage change when PEVs are connected to the domestic distribution system. Specifically, it assesses PEVs charging load by charging method in accordance with PEVs penetration scenarios, its percentage of total load, and voltage range under load conditions. Concretely, we develop EMTDC modelling to perform a voltage distribution analysis when the PEVs charging system by their charging scenario was connected to the distribution system under the load condition. Furthermore we present evaluation algorithm to determine whether it is possible to adjust it such that it is in the allowed range by applying ULTC when the voltage change rate by PEVs charging scenario exceed its allowed range. Also, detailed analysis of the impact of PEVs on power distribution system was carried out by calculating existing electric power load and additional PEVs charge load by each scenario on new-town in Korea to estimate total load increases, and also by interpreting the subsequent voltage range for system circuits and demonstrating conditions for countermeasures. It was concluded that total loads including PEVs charging load on new-town distribution system in Korea by PEVs penetration scenario increase significantly, and the voltage range when considering ULTC, is allowable in terms of voltage tolerance range up to a PEVs penetration of 20% by scenario. Finally, we propose the charging capacity of PEVs that can delay the reinforcement of power distribution system while satisfying the permitted voltage change rate conditions when PEVs charging load is connected to the power distribution system by their charging penetration scenario.

• 전기학회논문지P
• /
• 제54권2호
• /
• pp.88-93
• /
• 2005

Most of the LV customer have been applied the distribution system of 3-phase four wire system because of its advantage of supplying both of 1-phase & 3-phase loads simultaneously. Due to its structural simplicity, it is more convenient for use rather than the conventional separated scheme. But uneven load distribution or unclean voltage quality has occurred various problems such as de-rating, losses increase and vibration, etc. In this paper, voltage, current and power waveform in the actual fields have measured and analyzed in relation with internationally allowable voltage unbalance limits and compared the current unbalance factor with the load unbalance factor.

• 한국군사과학기술학회지
• /
• 제17권1호
• /
• pp.142-148
• /
• 2014

The mirror which is considered in designing a MFD is off-axis primary one and its dimension is wide 556mm height 345mm. The MFD(Mirror Fixation Device) load specification is generated for the high resolution mirror. The optical WFEs for unit loads are calculated from mirror sensitivity analysis and they are compared with allocated allowable optical WFE. The parasite load for the MFD is calculated from their comparison. The MFD compliant with the parasite load is designed.

• 한국지반환경공학회 논문집
• /
• 제14권11호
• /
• pp.13-23
• /
• 2013

서해안 연약지반에서 굴착 후 시멘트밀크의 주입없이 경타로 시공된 PHC 말뚝에 대하여 동재하시험과 정재하시험을 병행하여 그 상관성을 분석하였다. 초기 동재하시험은 Hydraulic Hammer(Ram Weight 7.0tf)를 사용하여 낙하고 0.8m에서 최종 평균 관입량은 3.0~8.0mm로 측정되었다. 이때 CAPWAP 분석결과에 의한 최종 허용지지력은 776.4~1,053.6kN/본으로 확인되었다. 정재하시험은 동재하시험을 한 동일 말뚝에 실시하는 것이 가장 이상적이나, 현장 여건상 인접의 말뚝에 설계지지력(120.0tf)의 200%인 총 시험하중(2,400.0kN)을 8단계로 나누어 재하시험한 결과, 총침하량은 15.97~16.38mm, 잔류침하량은 4.48~5.38mm로 측정되었으며, 모든 분석법을 적용하여도 항복하중과 극한하중은 확인되지 않았다. 따라서 최대시험하중(240.0tf)을 항복하중으로 간주하여 안전율 2.0으로 나누어 허용지지력을 산정한 결과 허용지지력은 1,200kN/본 이상 되는 것으로 나타났다. 그 결과 정재하시험보다 동재하시험이 1.54~1.1.4배 큰 것으로 나타났다.

• 콘크리트학회논문집
• /
• 제25권1호
• /
• pp.91-98
• /
• 2013

PHC 말뚝은 우수한 축하중 저항 능력에 비해 상대적으로 전단 및 휨 저항 성능이 낮은 단점을 가지고 있다. 이 연구의 목적은 기존 PHC 말뚝의 단점을 개선할 목적으로 개발된 중공부에 내부충전 콘크리트, 축방향 철근과 전단 철근으로 보강한 합성 PHC 말뚝(ICP 말뚝)의 휨성능을 평가하는 것이다. 이를 위하여 기존의 교대 설계사례로 부터 말뚝에 발생하는 축력과 휨모멘트를 조사한 후, ICP 말뚝 계산을 위하여 개발한 축력-휨모멘트 상관관계 프로그램을 이용하여 허용 축력과 휨모멘트가 발생하는 부재력을 만족하도록 ICP 말뚝을 설계하였다. 설계에 따라 ICP 말뚝을 제작하였으며, 휨실험을 수행하였다. 실험 결과 ICP 말뚝은 PHC 말뚝에 비하여 약 45% 큰 휨내력을 나타내었다. 또한 계산에 의해 예측한 ICP 말뚝 휨강도의 25%를 허용 휨모멘트로 취할 경우, 약 4.5의 안전율을 갖는 것으로 평가되었다.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2002년도 춘계학술대회논문집
• /
• pp.197-203
• /
• 2002

The estimation of pile bearing capacity is important since the design details are determined from the result. There are numerous ways of determining the pile design load, but only few of them are chosen in the actual design. According to the recent investigation in Korea, the formulas proposed by Meyerhof based on the SPT N values are most frequently chosen in the design stage. In the study, various static and dynamic formulas have been used in predicting the allowable bearing capacity of a pile. Further, the reliability of these formulas has been verified by comparing the perdicted values with the static and dynamic load test measurements. Also in cases, these methods of pile bearing capacity determination do not take the time effect consideration, the actual allowable load as determined from pile load test indicates severe deviation from the design value. The principle results of this study are summarized as follows : A a result of estimate the reliability in criterion of the Davisson method, in was showed that Terzaghi & Peck > Chin > Meyerhof > Modified Meyerhof method was the most reliable method for the prediction of bearing capacity. Comparisons of the various pile-driving formulas showed that Modified Engineering News was the most reliable method. However, a significant error happened between dynamic bearing capacity equation was judged that uncertainty of hammer efficiency, characteristics of variable , time effect etc... was not considered. As a result of considering time effect increased skin friction capacity higher than end bearing capacity. It was found out that it would be possible to increase the skin friction capacity 1.99 times higher than a driving. As a result of considering 7 day's time effect, it was obtained that Engineering News. Modified Engineering News. Hiley, Danish, Gates, CAPWAP(CAse Pile Wave Analysis Program ) analysis for relation, respectively, $Q_{u(Restrike)}$ $Q_{u(EOID)}$ = 0.971 $t_{0.1}$, 0.968 $t_{0.1}$, 1.192 $t_{0.1}$, 0.88 $t_{0.1}$, 0.889 $t_{0.1}$, 0.966 $t_{0.1}$, 0.889 $t_{0.1}$, 0.966 $t_{0.1}$

• 한국산학기술학회논문지
• /
• 제20권1호
• /
• pp.9-20
• /
• 2019

국내에서의 지진과 같은 자연재해의 발생횟수가 증가하고 있다. 이에 따라 재해, 재난 환경에 적합한 임시거주공간 혹은 피난시설의 필요성이 증대되고 있다. 본 연구에서는 경량 복합패널을 이용하여 기존 피난시설과는 차별화된 구호주거를 제작하고자 하였다. 이를 위해 경량 복합패널에 대한 구조적 성능을 검증하고자 하였으며, 패널에 대한 성능 시험 방법 중 ASTM E72 기준에 따른 면내 전단 강도 실험을 진행하였다. 실험 결과, 각 실험체가 면내 하중을 받을 때의 최대하중을 알아내었다. 모든 실험체는 가력 부분의 패널이 찢어지면서 실험이 종료되었다. 실험체의 초기 강성은 계산을 통해 예측한 강성과 일치하였다. 하지만 패널의 특성인 국부적인 찌그러짐과 찢어짐으로 인해 강성저하와 최종파괴가 발생하였다. 개구부가 있는 실험체들은 개구부의 위치와 형태에 따라 기본 실험체와 강성과 강도에서 차이를 보였다. 또한 모든 실험 결과를 종합하여 패널이 받는 최대하중과 힘을 받는 면적이 비례한다는 것을 확인하였다. 이를 통해 실험체들의 극한전단응력을 계산하였으며, 평균 극한전단응력을 산정하였다. 경량 복합패널의 평균 극한전단응력은 $0.047N/mm^2$이며, 이 값을 통해 패널의 면적에 따른 허용하중을 합리적으로 예측할 수 있는 근거를 제시하였다.

• Structural Engineering and Mechanics
• /
• 제59권4호
• /
• pp.703-718
• /
• 2016

Masonry arch bridges present a large segment of Iranian railway bridge stock. The ever increasing trend in traffic requires constant health monitoring of such structures to determine their load carrying capacity and life expectancy. In this respect, the performance of one of the oldest masonry arch bridges of Iranian railway network is assessed through field tests. Having a total of 11 sensors mounted on the bridge, dynamic tests are carried out on the bridge to study the response of bridge to test train, which is consist of two 6-axle locomotives and two 4-axle freight wagons. Finite element model of the bridge is developed and calibrated by comparing experimental and analytical mid-span deflection, and verified by comparing experimental and analytical natural frequencies. Analytical model is then used to assess the possibility of increasing the allowable axle load of the bridge to 25 tons. Fatigue life expectancy of the bridge is also assessed in permissible limit state. Results of F.E. model suggest an adequacy factor of 3.57 for an axle load of 25 tons. Remaining fatigue life of Veresk is also calculated and shown that a 0.2% decrease will be experienced, if the axle load is increased from 20 tons to 25 tons.