• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.162-171
• /
• 1995

The application of reciprocating engine crankshaft bearings is of particular importance and interest among the plain bearing, not only because the sheer volume of intemal combustion engines now produced, but because the severe operating conditions they are subjected to. Demands for better performances of crankshaft bearings have provide an important impetus in the development of bearings and bearing materials. As engine design progresses toward higher outpt and higher efficiency, crankshaft bearings must perform under more seveve operating conditions. Higher load, temperature, and speed as well as lower viscosity oil are applied to the bearing sysem, resulting in a smaller minimum oil film thickness. This means more solid-solid contact between the shaft and bearing, and the bearing is exposed to more danger of seizure. Some engines may experience bearing seizure problems. However, understanding about the seizure behavior and mechanism is far from being enough. Seizure resistance of a bearing-shaft system will be affected by the properties of the shaft and bearing, especially their materials and surface texture. Commonly used engine bearing materials include Al-Pb-Si, Al-Sn-Si, Al-Sn, and Cu-Pb with Pb-Sn-Cu overlay. These materials have very different properties. They showed different behaviors dering seizure tests and seizure may occur with different mechanism for different bearing material. Shaft materials also affect the seizure resistance of the system. Surface texture of the bearing and shaft have apparent effects on the lubrication and solid-solid contact pattern, and therefore will affect the seizure behavior of the system. Bearings and shafts which are made of different materials and have different surface textures have been tested and analyzed. Their effects on seizure resistance are discussed and possible seizure mechanisms for different beatings are presented in this paper.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.37-45
• /
• 2008

In this study, reliabilities of Cu (60 um)/SnAg (20 um) double-bump flip chip assemblies were investigated for the flip chip interconnections on organic substrates with 100 um pitch. After multiple reflows at $250^{\circ}C\;and\;280^{\circ}C$, bump contact resistances were almost same regardless of number of reflows and reflow temperature. In the high temperature storage test, there was no bump contact resistance change at $125^{\circ}C$ up to 2000 hours. However, bump contact resistances slightly increased at $150^{\circ}C$ due to Kirkendall voids formation. In the electromigration test, Cu/SnAg double-bump flip chip assemblies showed no electromigration until about 600 hours due to reduced local current density. Finally, in the thermal cycling test, thermal cycling failure mainly occurred at Si chip/Cu column interface which was found out the highest stress concentration site in the finite element analysis. As a result, Al pad was displaced out under thermal cycling. This failure mode was caused by normal compressive strain acting Cu column bumps along perpendicular direction of a Si chip.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.201-202
• /
• 2002

The abrasive wear behaviour of $Al_2O_3$ particle-reinforced aluminium composite was investigated. The wear rate of the composite and the matrix alloy has been expressed in terms of the applied load, sliding distance and particle size using linear factorial design approach.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.11a
• /
• pp.38-42
• /
• 1991

Super Duralumin (A2024 - T3)은 가볍고 내식성이 양호할 뿐만 아니라, 석출물($CuAl_2$, $Mg_2$Si)에 의한 시효 경화로 인하여 고강도의 성질을 가지고 있으므로 구조용재, 반공기 및 운반기에 널리 사용되고 있지만, 절삭가공에서 많은 문제점을 내포하고 있다. 따라서 이러한 문제점에 대한 절삭성 향상이 절실히 요구되고 있는 설정이다. 일반적으로 피삭성을 검토하는 경우 철강재료는 공구마멸에 중점을 두지만, Al합금에 있어서는 공구마멸보다는 가공면의 양부를 중요시한다. 이것은 Al이 연질재이므로 절삭시 표면층에 유동이 생겨 양호한 절삭가공면을 얻기 어렵기 때문이다.(중략)

• Journal of Welding and Joining
• /
• v.35 no.2
• /
• pp.23-29
• /
• 2017

Mechanical properties and hardness distributions in arc brazed joints of Dual phase steel using Cu-Al insert metal were investigated. The maximum tensile shear load was 10.4kN at the highest brazing current. It was about 54% compared to tensile load of base metal. This joint efficiency is higher than that of joint of DP steel using Cu-based filler metals which are Cu-Si, Cu-Sn. Fracture positions can be divided into two types. Crack initiation commonly occurred at three point junction among upper sheet, lower sheet and the fusion zone. However crack propagations were different with increasing the brazing current. In case of the lower current, it instantaneously propagated along with the interface between fusion zone and upper base material. On the other hand, in case of higher current, a crack propagation occurred through fusion zone. When the brazing current is low (60, 70A), the interface shape is flat type. However the interface shape is rough type, when the brazing current is high (80A). It is thought that the interface shapes were the reason why the crack propagations were different with brazing current. The interface was the intermetallic compounds which consisted of $(Fe,Al)_{0.85}Cu_{0.15}$ IMC formed by crystallization at $1200^{\circ}C$during cooling. Therefore the maximum tensile shear load and the fracture behavior were determined by a interface shape and effective sheet thickness of the fracture position.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.691-695
• /
• 2018

In this study, we investigate the recycling of aluminum-based metal matrix composites(AMCs) embedded with SiC particulates. The microstructure of the AMCs is characterized by X-ray diffraction and scanning electron microscopy. The possibility of recycling the composite scrap is attempted from the melted alloy and SiC particulates by re-melting, holding and solidification in crucibles. The recovery percentage of the matrix alloy is calculated after a number of holding times, 0, 5, 10, 15, 20, 25 and 30 minutes and for different particulate sizes and weight fractions in the Al matrix. The results show that the recovery percentage of the matrix alloy, as well as the time required for maximum recovery of the matrix, is dependent on the size and weight fraction of SiC particulates. In addition, the percentage recovery increases with particulate size but drops with the particulate fraction in the matrix. The time to reach maximum recovery falls rapidly with an increase in particulate size and fraction.

• Journal of Korea Foundry Society
• /
• v.17 no.4
• /
• pp.347-355
• /
• 1997

It is well known that the coarse primary Si in hypereutectic Al-Si alloys deteriorate castability, machinability, and mechanical properties. So, many treatment has been tried to refine the primary Si increasing cooling rate and adding refinement agent. Therefore. the purpose of our work was the observation of the effect on the refinement of primary Si and the analysis of the trend to apply to the casting process by changing the amount of P addition and the cooling rate while fixing the temperature at $750^{\circ}C$ of P addition and the type of AlCuP. In the condition of amount of P addition was fixed, primary Si was finer as cooling rate increased but in case of cooling rate was fixed, the effect of refinement was resisted as incersed the amount of P addition. At a relatively slow cooling rate of $22^{\circ}C/sec$, refinement was governed by the amount of P addition rather than cooling rate. At elevated cooling rate of $51^{\circ}C/sec$ and $99^{\circ}C/sec$, the undercooling due to faster cooling rate promoted nucleation of primary Si rather than P addition more significantly.

• Journal of Conservation Science
• /
• v.33 no.3
• /
• pp.215-223
• /
• 2017

The purpose of this study is to reveal the characteristics, correlations, and colorant materials of those using the chemical compositions of 30 glasses excavated from the Sarari hall of the Mireuksaji stone pagoda, and to determine the correlations between them and other glass excavated from the Wanggungri site. The results of the chemical analysis of the 11 glass beads show that they are a soda glass group with high contents of $SiO_2$ and $Na_2O$; these can be further subdivided into soda-alumina groups ($Na_2O-Al_2O_3-CaO-Si_2O$). The characteristics of the stabilizer are classified as being of the high alumina glass group (LCHA), except for two glasses. It was concluded that colorant materials affected the coloring for glass beads by various components including Ti, Mn, Fe, Cu and Pb. In addition, we examined six lead glasses which are glass plate and unknown fragments that are of a common lead glass system ($PbO-SiO_2$) with respect to the average contents of PbO (70wt.%) and $SiO_2$ (30wt.%). As a result of comparing these relics with those of the glass beads excavated by Wanggungri, there is a similarity in that they belong to the soda glass group. However, the contents of $Na_2O$ are relatively higher than that of the glass beads in the Mireuksaji pagoda, and most of relics include glasses with a low content of $K_2O$ and CaO. In addition, the PbO and $SiO_2$ contents are slightly different in the lead glass. It seems that the glass relics made at two different sites may have used different raw materials or techniques.

• Transactions of Materials Processing
• /
• v.12 no.6
• /
• pp.588-596
• /
• 2003

The relationships between evolution of microstructure and mechanical properties of porous Al-3Si-2Mg-2Cu alloy after the foaming and various heat treating were investigated. The foamed alloy having various densities were manufactured by powder compact foaming and heat treated. Then compression test was performed with deformation rate of 0.5/s. The ultimate compression strength was not changed after solution heat treatment but the flow curve after ultimate strength showed very smooth and uniform plateau region. This change of flow curve means that the deformation mechanism is altered from brittle fracture to ductile deformation and the energy absorption property of Al foam is dramatically improved. The improvement of energy absorption without any detriment of mechanical properties is due to that the very brittle precipitation like Al-Cu and Al-Mg was uniformly dissolved in Al matrix after solution heat treatment. And various mechanical properties of Al alloy porous material were improved by 40% with aging of $200^{\circ}C$ and 50min. These improvements are ascribe to the various fine precipitates like $\Omega$ and $\theta$'.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.141-141
• /
• 2018

Copper is one of the most abundant metals on earth. Its oxide (CuO) is an intrinsically p-type metal-oxide semiconductor with a bandgap ($E_g$) of 1.2-2.0 eV 1. Copper oxide nanomaterials are considered as promising materials for a wide range of applications e.g., lithium ion batteries, dye-sensitized solar cells, photocatalytic hydrogen production, photodetectors, and biogas sensors 2-7. Recently, high-density and uniform CuO nanostructures have been grown on Cu foils in alkaline solutions 3. In 2011, T. Soejima et al. proposed a facile process for the oxidation synthesis of CuO nanobelt arrays using $NH_3-H_2O_2$ aqueous solution 8. In 2017, G. Kaur et al. synthesized CuO nanostructures by treating Cu foils in $NH_4OH$ at room temperature for different treatment times 9. The surface treatment of Cu in alkaline aqueous solutions is a potential method for the mass fabrication of CuO nanostructures with high uniformity and density. It is interesting to compare the gas sensing properties among CuO nanomaterials synthesized by this approach and by others. Nevertheless, none of above studies investigated the gas sensing properties of as-synthesized CuO nanomaterials. In this study, CuO nanowalls versus nanoparticles were synthesized via the oxidation process of Cu foil in NH4OH solution at $50-70^{\circ}C$. The gas sensing properties of the as-prepared CuO nanoplates were examined with $C_2H_5OH$, $CH_3COCH_3$, and $NH_3$ at $200-360^{\circ}C$.