• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.528-533
• /
• 2002

The mechanical and metallurgical properties of friction welded joints type 5052 Al alloy/A36 steel have been studied in this paper. The joint strength increased with increasing upset pressure and friction time till it reached the critical value. The joint strength was fixed at low strength compare to that of base metal in the case of increasing friction time. Microstructure of 5052 Al alloy was greatly deformed near the weld interface. The very fine and equaxied grain structure was observed at the near interface. The elongated grain was formed outside dynamic recrystallizatoin region at the peripheral part, while the A36 steel' side was not deformed. The hardness of the near interface was slightly softer than that of 5052 Al alloy base metal. The maximum softening width was about 8mm from the interface. In the present work, the friction welding condition, t$_1$=0.5sec, P$_2$=137.5MPa, showed a maximum joint strength (202MPa) when friction pressure, upset time and rotation speed were fixed at 75MPa, 5sec, 2000rev/min and these were the optimum friction welding condition of 5052Al/A36 steel joints.

• Journal of Welding and Joining
• /
• 제22권3호
• /
• pp.69-76
• /
• 2004

Effects of friction stir welding parameters such as tool rotation speed and welding speed on the joints properties of 5052 Al alloys were studied in this study. A wide range of friction stir welding conditions could be applied to join 5052 AA alloy without defects in the weld zone except for certain welding conditions with a lower heat input. Microstructures near the weld zone showed general weld structures such as stir zone (SZ), thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ). Each zone showed the dynamically recrystallized grain, transient grain and structure similar to base metal's, respectively. Hardness distribution near the weld zone represented a similar value of the base metal under wide welding conditions. However, in case of 800 rpm of tool rotation speed, hardness of the stir zone had a higher value due to the fine grain with lots of dislocation tangle, a higher angle grain boundary and some of Al3Fe particles. Except joints with weld defects, tensile strength and elongation of the joints had values similar to the base metal values and fracture always occurred in the regions approximately 5mm away from the weld center.

• 소성∙가공
• /
• 제17권2호
• /
• pp.102-106
• /
• 2008

Cryogenic rolling combined with warm rolling has been found more effective than a single cryogenic rolling process in improving the strength of a 5052 Al alloy. In this study, cryo-rolled 5052 Al alloys were warm-rolled at $175^{\circ}C$. A notable increase of tensile strength was achieved by the precipitation during warm rolling process. Mechanical behavior of this alloy was investigated using hardness and tensile tests. It was found that the cryogenic rolling process combined with warm rolling process was very effective in improving tensile strength.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.81-83
• /
• 2007

Cryogenic rolling combined with warm rolling has been found to be more effective than only cryogenic rolling procedure in improving the strength of a 5052 Al alloy. In this study, cryo-rolled 5052 Al alloys were aged at $175^{\circ}C$. Warm rolling was conducted after dipping plates into silicon oil bath. A notable increase of tensile strength is achieved by the precipitation during warm rolling. The mechanical behavior of this alloy was investigated by hardness and tensile tests. The microstructure was investigated by transmission electron microscopy. It was found that the cryogenic rolling combined with warm rolling was very effective in improving tensile strength.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.152-155
• /
• 2003

In order to examine the springback of aluminum alloy sheets, AL1050 and AL5052, in the warm forming which forms the sheet above room temperature, the stretch bending and draw bending tests in various working temperatures were carried out. While the springbacks of AL5052 and AL1050 are tremendously reduced over 150$^{\circ}C$ in the stretch bending test, the springbacks in the draw bending test are rapidly reduced in 150$^{\circ}C$-200$^{\circ}C$ for AL5052 and 200$^{\circ}C$-250$^{\circ}C$ for AL1050. Using the FEM program, the forming and springback processes are analyzed. Though springback amounts of analysis result are slightly bigger than those of experiment, they showed the same trend in the decreasing springback as the forming temperature increases.

• 비파괴검사학회지
• /
• 제30권2호
• /
• pp.146-154
• /
• 2010

알루미늄 5052 합금의 탄성특성에 대한 ECAP 강소성변형과 어닐링효과를 연구하였다. 알루미늄 5052 합금은 용체화 처리 후 ECAP 가공하고 어닐링처리를 수행하였다. 탄성계수는 기존의 인장시험과 나노압입시험을 통해 측정하고 음향현미경의 음향재료신호를 이용하여 시료의 표변에서 탄성계수를 측정하였다. 기존의 시험법으로는 불가능한 소성변형과 열처리에 따른 탄성계수의 변화를 음향재료신호를 이용하여 성공적으로 측정하였고 개개의 결정립에서도 결정방위에 의존하는 탄성계수를 얻었다.

• Corrosion Science and Technology
• /
• 제19권5호
• /
• pp.250-258
• /
• 2020

Recently, 5000 series and 6000 series Al alloys have been used as hull materials for small and medium-sized ships because of their excellent weldability, corrosion resistance, and durability in marine environments. Al ships can navigate at high speed due to their light weight. However, cavitation-erosion problems cause reducing durability of Al ship at high speed. In this investigation, 5052-O, 5083-H321, and 6061-T6 Al alloy materials were used to evaluate the damage characteristics with amplitude (cavitation strength). As a result of the electrochemical experiments, the corrosion current density and corrosion potential of 6061-T6 in seawater were 8.52 × 10-7 A/㎠ and -0.771 V, respectively, presenting the best corrosion resistance. The cavitation-erosion experiment showed that 5052-O had the lowest hardness value and cavitation-erosion resistance. 5052-O also had a very short incubation period. As the experiment progressed for 5052-O, pitting formed and grew in a short time, and was observed as severe cavitation-erosion damage that eliminated in large quantities. Among the three specimens, 5083-H321 presented the highest hardness value and the damage rate was the smallest after the initiation of pitting.

• Journal of Welding and Joining
• /
• 제28권6호
• /
• pp.58-62
• /
• 2010

In this study, the bead-on-plate welding were conducted by using GMA welding and plasma-GMA welding on Al 5052 and, Al 6061 plates. For these processes, the maximum welding speeds for full penetration were compared, and various weld qualities such as bead appearance, cross-section, cracks and porosities were examined. Faster welding speed, cleaner bead surface and more stable drop transfer could be achieved by plasma-GMA welding, compared with GMA welding.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.112-114
• /
• 2006

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.253-253
• /
• 2012