• 콘크리트학회논문집
• /
• 제24권5호
• /
• pp.613-621
• /
• 2012

철근부식은 콘크리트의 내구성 문제뿐 아니라 구조적인 안전성에 영향을 미치므로 매우 중요한 열화이다. 철근부식을 방지하기 위하여 콘크리트 구체의 내구성을 향상시키려는 연구가 진행되고 있으나 용융아연도금 철근과 같이 철근 표면을 코팅함으로서 부식을 방지하려는 연구도 진행되고 있다. 이 연구는 용융아연도금 철근의 내부식성능 및 구조성능을 정량적으로 평가하는 것이다. 이를 위하여 아연, 알루미늄, 아연 45% + 알루미늄 55% 등을 사용한 도금 철근에 대하여 예비실험을 수행하였다. 다양한 금속코팅재료의 부식거동을 평가하여 최적의 도금재료인 아연을 선정하였으며, 아연도금 철근의 전위변화를 촉진염수 분무실험 등을 통하여 평가하였다. 또한 용융아연 도금된 철근과 일반철근을 이용하여 철근의 인장강도 시험, 콘크리트와의 부착력 시험 등이 수행되었으며, 최종적으로 RC 보를 제작하여 균열패턴 및 구조거동을 평가하였다. 이 연구에서는 다양한 금속코팅재료의 부식거동, 노치를 가진 금속의 전위변화 등을 포함한 부식특성이 평가되었다. 또한 부착력, 인장강도, 하중에 따른 거동 등을 포함한 구조적 거동이 평가되었으며, 최종적으로 용융아연도금 철근의 사용에 대한 적용성이 검토되었다.

• 한국표면공학회지
• /
• 제30권3호
• /
• pp.183-190
• /
• 1997

Fabrication and crystallization characteristics of yttria($T_2O_3$) stabilized zirconia(YSZ) thin film by sol-gel process were studied. YSZ sol was synthesized with zirconium n-propoxide($Zr(OC_3H_7)_4)$) and yttrium nitrate pentahydrate ($Y(NO_3)_3.5H_2O$). YSZ film was prepared by depositing the polymeric sol on porous $Al_2O_3$ substrate by spin-coating, and the film characteristics were investigated by FRIR, TG-DTA, XRD, DSC, optical microscopy and SEM. The film topology was uniform and cracks were not found. It was found that the annealing temperature and the concentration of stabilizer affect the crystallization of YSZ film. The YSZ film began to crystallize from amorphous to tetragonal phase at 40$0^{\circ}C$, and it was not converted to cubic structure until $1100^{\circ}C$. It seemed that the grains were formed over $700^{\circ}C$and the average grain size was obtained about 0.2$\mu\textrm{m}$.

• 한국전기전자재료학회논문지
• /
• 제14권9호
• /
• pp.762-767
• /
• 2001

We report the white light emission from the multilayer organic electroluminescent(EL) device using exciplex emission. The exciplex at 500nm originated between poly(N-vinylcarvazole)(PVK) and 2,5-bis(5'-tert-butyl-2-benzoxazoly)thiophene(BBOT) and exciplex of 50nm originated from N,N'-diphenyl-N,N'-(3-methyphenyl)-1,1'-biphenyl-4,4'-diamine(TPD) and BBOT were observed. Also, the energy transfer from PVK to BBOT and poly(3-hexylthiophene)(P3HT) in mixed emitting materials was occurred. The electroluminescence(EL) spectra of organic EL device which have a device structure of ITO/CuPc(5nm)/emitting layer(100nm)/BBOT(30nm)/LiF(1.4nm)/Al(200nm) were slightly changed as a function of the applied voltage. The luminance fo 12.3 ${\mu}$W/$\textrm{cm}^2$ was achieved at 20V and EL spectrum measured at 20V corresponds to Commission Internationale de L\`Eclairage(CIE) coordinates of x=0.29 and y=0.353.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.427-431
• /
• 2005

In this study, 6' GaAs wafer bonding system is designed and optimized to bond 6 inches device wafer and material wafer. Bonding process is performed in vacuum environment and resin is used to bond two wafers. Vacuum module and double heating mechanisms are adopted to minimize wafer warpage and void. Structure and heat transfer analysis, et al of the core modules review the designed mechanisms are very effective in performance improvement. As a result, high productivity (tack time cut-down) and stabilized process can be obtained by reducing breakage failure of wafer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.101.1-101.1
• /
• 2015

플라즈마에 의한 식각 공정중 챔버 내에서 발생한 오염입자가 기판위에 떨어져 제품의 불량을 일으키고 그에 따른 부품 교체비용이나 교체시 가동을 멈춰야하는 문제점들이 있다. 이러한 문제점을 해결하기 위해 내플라즈마성이 우수하다고 알려진 아노다이징 피막을 사용하고 있다. 하지만 다양한 아노다이징 공법중 어떠한 요인이 내플라즈마 특성과 관계되는지에 대한 보고는 부족한 실정이다. 기존의 아노다이징 특성평가방법으로는 내화학 특성과 열안정성 평가, 구조적 특성을 확인하는 것이 주로 사용되어 왔다. 따라서 본 연구에서는 기존 내화학 특성과 열안정성이 우수하다고 알려진 황산-주석산법을 이용한 피막의 특성을 평가하여 내화학특성, 열적 안정성, 구조적 특성이 내플라즈마 특성과 어떠한 관계가 있는지 확인했다.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.156-158
• /
• 2002

BSCCO tpaes with insulating ceramic barriers such as Zr$O_{2}$, $Al_{2}$$CO_{3}$, and Sr$CO_{3}$ were fabricated and their electrical properties were evaluated. Each filament was dip coated with ceramic slurries and then made 19 multifilamentary tapes by the “powder-in-tube” process. Microstructural investigation showed that filaments were completely decoupled each other and had a significant sausage effect. The critical current of coated tapes was reduced compared to that of non coated one, and its reduction was varied with the coating materials. For tapes with coated with Sr$CO_{3}$, the critical current was measured to be 7.2 A which was 44% reduction to that of non coated one. This reduction is believed to be due to the formation of sausage effect and non-uniform microstructure.

• 한국표면공학회지
• /
• 제29권4호
• /
• pp.253-260
• /
• 1996

Regular spangle hot dip galvanized steel sheets were made in the zinc bath containing a small amount of Al and with the addition of Pb, Sb, Sb-Mg, Sb-Cu and Bi respectively whose average glosses were measured. Zero-spangle hot dip galvanized steel sheets were also made by spraying a 2% $NH_4H_2PO_4$ solution on molten coating surfaces with exactly the same chemical compositions as above used for regular spangle and whose glosses and corrosion losses were also evaluated. For manufacturing zero- spangle hot dip galvanized steel sheets with high brightness, the zinc bath with 0.02%Sb and the spraying of a 2% $NH_4H_2PO_4$ solution were proposed and for better brightness and corrosion resistance, the zinc bath with 0.02% Sb-0.50%Mg and the spraying of a 2% $NH_4H_2PO_4$ solution were also proposed.

• 한국세라믹학회지
• /
• 제15권2호
• /
• pp.89-97
• /
• 1978

The basic mechanism of adherence in sintered high purity alumina ceramic-to-metal bonding was studied. Emphasis was placed on flux composition, porosity of the fired ceramics, and metallizing mixtures. The study was conducted on 95 and 99.5% alumina, using molydbenum-manganese, molybdenum-manganese-silicon dioxide metallizing compositions. Metallizing was performed in wet hydrogen (dew point, ＋17$^{\circ}C$) at 145$0^{\circ}C$ for 45min. This experiment indicated that adhernece mechanism of ultra high purity alumina ceramic was attributed to formation of $MnAl_2O_$4, and in the case of 95% alumina containing glass, the migration of glass from the interface into the void of the metal coating was the main role to the adhrence. It showed also that greater the bond-strength was resulted as porosity was increased.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.35-40
• /
• 2003

본 연구에서는 취성재료이면서, 세라믹과 유사한 성질을 가지며 내부균열관찰이 용이한 상업용 유리의 표면에 세라믹 플라즈마 용사 코팅한 후 입자 충격시험을 실시하였다. 코팅분말로는 매마모성 및 내충격성이 우수하여 산업계에서 널리 사용되고 있는 $Al_{2}O_{3}$ 분말을 사용하였으며, 충격입자로는 고경도의 STB2 볼베어링강을 사용하였다. 공기압축기를 장착한 입자 충격시험기를 이용하여 강구입자 충격시험을 실시한후, 실체현미경을 이용하여 손상정도를 분석하였다. 그리고 코팅입자의 크기 및 기공율에 따른 손상 정도를 분석 방법에 따라 손상정도를 비교${\cdot}$검토하였다.

• 한국세라믹학회지
• /
• 제28권6호
• /
• pp.478-482
• /
• 1991

Numerous researchers have observed the bubble formation from C/C composite at high temperature (1300$^{\circ}C$∼1700$^{\circ}C$). According to thermodynamic calculation, the bubble can be formed at the temperatures above 1500$^{\circ}C$ in the case of SiC coated C/C composite. However, the bubble below 1500$^{\circ}C$ could not be explained. Therfore, in an effort to explain the low temperature bubble formation, the effects of inhibitors such as B, Al, Zr and Si were thermodynamically investigated along with hydrogen and water vapor impurities resolved in C/C composite and SiC coating layer.