• Journal of Welding and Joining
• /
• 제17권6호
• /
• pp.62-69
• /
• 1999

The advantages of Thermal sprayed coatings as a replacement for cast iron liners are reduced weight, better heat transfer and reduced cost. One of the most important performance attributes of a cylinder bore coating is its wear resistance, since it must survive the abrasive sliding of both the piston rings and the piston skirt. In this study, composite powders were prepared by ball milling of Al-13Si-3Mg(wt%) alloy with SiC particles. The concentrations of SiC were 40 and 60wt%. The composite powders were sprayed using Metco-9MB plasma torch. Plasma sprayed coatings were heat-treated at 500℃ for 3 hours. The wear resistances of the plasma sprayed coatings were found to improve with heat treatment and superior to the commercially available G.C.I.(gray cast iron). AlSiMg-40SiC heat-treated coatings showed the best wear resistance in this study.

• Corrosion Science and Technology
• /
• 제23권2호
• /
• pp.83-92
• /
• 2024

A hot-dip simulator was utilized to replicate abnormal coating buildup observed during line stops at galvanize lines, assessing the influence of processing conditions on buildup (up to 14 mm/side). Steel samples from 19 coils (comprising IF, BH, LCAK, HSLA, DP600-DP1180, Si: 0.006 - 0.8 wt%, P: 0.009 - 0.045 wt%) were examined to explore the phenomenon of heavy coating growth. It was discovered that heavy coating buildup (~3 mm/h) and rapid strip dissolution (~0.17 mm/h) in a GA or GI pot can manifest with specific combinations of steel chemistry and processing conditions. The results reveal the formation of a unique coating microstructure, characterized by a blend of bulky Zeta crystals and free Zn pockets/networks due to the "Sandlin" growth mechanism. Key variables contributing to abnormal coating growth include steel Si content, anneal temperature, dew point in heating and soaking furnaces, Zn pot temperature, Zn bath Al%, and cold-rolling reduction%. At ArcelorMittal Dofasco galvanize lines, an automatic online warning system for operators and special scheduling for incoming Si-bearing steels have been implemented, effectively preventing further heavy buildup occurrences.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.179-179
• /
• 2013

현재 자동차 분야에서 차량 경량화를 통해 연비 향상 및 에너지 효율 향상을 기대하고 있으며, 차량 경량화의 한 수단으로 자동차용 유리를 고강도 투명 플라스틱 소재인 PC (Polycarbonate)로 대체하고자 하는 연구가 활발히 이루어지고 있다. 그러나, PC의 낮은 내마모 특성과 자외선에 의한 열화 및 변색 현상은 해결하여야 할 중요한 문제점으로 지적되고 있다. 본 연구에서는, PC의 내마모 특성을 향상시키기 위하여 transmittance가 확보되고, 고경도 특성을 갖는 Al-Si-N 박막 증착에 대한 연구를 하였다. Al-Si-N 박막 증착을 위하여 ICP-assisted reactive magnetron sputtering 장비를 이용하였으며, 고경도 특성을 갖는 Al-Si-N 박막을 제조하였다. 분석 장비로는 박막의 chemical state와 crystallinity를 확인하기 위하여 XPS (X-ray Photoelectron Spectroscopy), AES (Auger electron spectrscopy)와 XRD (X-ray diffraction)를 이용하여 분석을 수행하였으며, Knoop ${\mu}$-hardness tester와 Pin-on-disk를 이용하여 경도 및 내마모 특성을 평가하였다. Al-Si-N 박막의 두께는 ~5,000 ${\AA}$을 증착하였으며, 가시광 영역에서 평균 92%의 transmittance를 나타내었다. 박막의 Si/(Al+Si) 비율에 따라 다른 경도 특성을 나타냈는데, Si/(Al+Si) 비율이 26~32% 부근에서 최대 31 GPa의 경도 값을 확인 할 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.263-264
• /
• 2007

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 추계학술발표 개요집
• /
• pp.187-188
• /
• 1994

• 한국분말재료학회지
• /
• 제27권3호
• /
• pp.210-218
• /
• 2020

A T-800 (Co-Mo-Cr) coating material is fabricated using Co-Mo-Cr powder feedstock and laser cladding. The microstructure and melted Al erosion properties of the laser-cladded T-800 coating material are investigated. The Al erosion properties of the HVOF-sprayed MoB-CoCr and bulk T-800 material are also examined and compared with the laser-cladded T-800 coating material. Co and lave phases (Co₂MoCr and Co₃Mo₂Si) are detected in both the laser-cladded T-800 coating and the bulk T-800 materials. However, the sizes of the lave phases are measured as 7.9 ㎛ and 60.6 ㎛ for the laser-cladded and bulk T-800 materials, respectively. After the Al erosion tests, the erosion layer thicknesses of the three materials are measured as 91.50 ㎛ (HVOF MoB-CoCr coating), 204.83 ㎛ (laser cladded T-800), and 226.33 ㎛ (bulk T-800). In the HVOF MoB-CoCr coating material, coarse cracks and delamination of the coating layer are observed. On the other hand, no cracks or local delamination of the coating layer are detected in the laser T-800 material even after the Al erosion test. Based on the above results, the authors discuss the appropriate material and process that could replace conventional bulk T-800 materials used as molten Al pots.

• 열처리공학회지
• /
• 제25권6호
• /
• pp.283-291
• /
• 2012

In order to increase the anti-oxidation property during the tailor welding blanked hot press forming process for a high strength boron steel sheet, we performed a different coating method on the boron-steel sheet such as 87% Al - 13% Si and Fe - 8.87 Zn dipping plating procedure. However, during laser welding process, the Al-Si coated steel sheet has showed a low tensile strength and about half value of elongation than the original boron-steel sheet. Aluminum and silicon, elements of coating layer were diffused into the boron-steel matrix and have shown a low strength result than non-coated specimen. On the other hand, Zinc-coated boron-steel has expectedly showed a excellent tensile strength and micro-harness value in the welded area like original boron-steel.

• 한국결정성장학회지
• /
• 제24권2호
• /
• pp.65-69
• /
• 2014

A1100, A5052, A6061, A6063, A7075 규격의 시판 알루미늄 합금 판재를 $Na_2SiO_3$와 $Na_2P_2O_7$ 전해질에서 pulse폭 $2000{\mu}sec$, + impulse 420 V, $400{\mu}sec$, -impulse $300{\mu}sec$의 bipolar pulse로 플라즈마 전해 산화 코팅(plasma electrolytic oxidation coating)한 산화피막의 결정상을 분석하였다. 표면에 형성된 산화물의 결정상은 ${\alpha}-alumina$, ${\gamma}-alumina$, ${\eta}-alumina$, $Al_{4.95}Si_{1.05}O_{9.52}$, 그리고 $(Al_{0.9}Cr_{0.1})_2O_3$가 관찰되었다. Bipolar pulse에 의해서 전해액의 성분인 Si가 산화피막에 포함되며, 포함된 Si는 결정상을 형성하기도 하지만 유리상을 형성시킨다. 이때 합금의 Mg 성분은 유리상의 양을 증가시킨다. Micro plasma에 의해서 용융된 표면은 유리상이 먼저 형성되고 이후 계속된 micro plasma의 열에 의하여 새로운 결정상으로 전이가 일어나는 과정을 거치며, 이에 따라 기존에 보고된 결정상이외에도 다양한 결정상이 형성될 수 있음을 추측할 수 있다.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.

• 한국주조공학회지
• /
• 제37권6호
• /
• pp.186-192
• /
• 2017

The lost foam casting method was used to fabricate Al-Si alloy thin sheet specimens; the effects of chemical composition and process variables on the mold filling and mechanical properties were investigated. The mold filling capability was observed to be proportional to the pouring temperature, and both the vibration imposed during the casting and the application of a pattern coating had rather negative effects. The mold filling capability also decreased with the addition of Mg or TiB. When the Mg content increased, the tensile strength of the cast alloy was enhanced, but the elongation decreased. However, after T6 heat treatment, both the strength and the elongation were improved. TiB addition for grain refining or pattern coating did not significantly affect the tensile properties.