• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.331-340
• /
• 1995

Microwave (Hybrid) Heating (MHH) was used to oxidize and sinter Al-Al2O3 powder mixture. For 25 v/o Al specimen and 35 v/o Al specimen, the total processing to produce low-shrinkage reaction bonded alumina was carried out within 1 hour even though conventional furnace process took more than 10 hours. Compared with conventional fast firing process, MHH process increased more than 40% oxidation at the same temperature, and these high oxidation rates were thought to be caused by the surface ohmic current on Al particles.

• 한국재료학회지
• /
• 제24권5호
• /
• pp.236-242
• /
• 2014

Fabrication of reaction-bonded $Al_2O_3$ (RBAO) ceramics using Al-Zn-Mg alloy powder was studied in order to improve traditional RBAO ceramic processing using Al powder. The influence on reaction-bonding and microstructure, as well as on physical and mechanical properties, of the particulate characteristics of the $Al_2O_3$-Al alloy powder mixtures after milling, was revealed. Variation of the particulate characteristics of this $Al_2O_3$-Al alloy powder mixture with milling time was reported previously. To start, the $Al_2O_3$-Al alloy powder mixture was milled, reaction-bonded, post-sintered, and characterized. During reaction-bonding of the $Al_2O_3$-Al alloy powder mixture compacts, oxidation of the Al alloy took place in two stages, that is, there was solid- and liquid-state oxidation of the Al alloy. The solid-state oxidation exhibited strong dependence on the density of surface defects on the Al-alloy particles formed during milling. Higher milling efficiency resulted in less participation of the Al alloy in reaction-bonding. This was because of its consumption by chemical reactions during milling, and subsequent powder handling, and could be rather harmful in the case of over-milling. In contrast to very little dependence of oxidation of the Al alloy on its particle size after milling, the relative density, microstructure, and flexural strength were strongly dependent on particle size after milling (i.e., on milling efficiency). The relative density and 4-point flexural strength of the RBAO ceramics in this study were ~98% and ~365 MPa, respectively, after post-sintering at $1,600^{\circ}C$.

• 한국세라믹학회지
• /
• 제23권3호
• /
• pp.1-8
• /
• 1986

The preparation and electrical conductivity of $\beta$-$Al_2O_3$ are investigated as a function of $Na_2O$ content from the-oretical composition of $\beta$-$Al_2O_3$ to that of $\beta$"-$Al_2O_3$. $\beta$-$Al_2O_3$ $\beta$"$Al_2O_3$$\alpha$-Al2O3 and ${\gamma}$-NaAlO2 phases appear in the calcined powder at 125$0^{\circ}C$ for 2 hours. The majoity phase is $\beta$-$Al_2O_3$ in sintered specimens at 155$0^{\circ}C$ and 1$650^{\circ}C$ for 30 mins respectively and ${\gamma}$-4NaAlO_2$ phase also exists when Na2O content is over 10.39w/o ${\gamma}$-4NaAlO_2$ phase does not affect the grain growth of $\beta$-$Al_2O_3$ in sintering at 155$0^{\circ}C$ but acts as a reactive liquid for the abnormal grain growth of $\beta$-$Al_2O_3$in sintering at 1$650^{\circ}C$ The electrical conduction of $\beta$-$Al_2O_3$is predominated by 4Na^+$ ion. Contribution of ionic con-ductivity to total conductivity is gradually decreased with increasing temperature at given oxygen pressure and to -tal conductivity is increased by positive hole due to interstitial oxygen with increasing oxygen pressure.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.968-980
• /
• 1995

Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites are fabricated by the direct squeeze infiltration method. From the microstructure of Al/Al$_{2}$O$_{3}$/C composites, uniform distribution of reinforcements and good bondings are found. Optimum processing conditions for preforms and squeeze castings are suggested. Mechanical properties, such as elastic modulus, elongation, 0.2% offset yield strength and ultimate tensile strength are obtained. Through the abrasive were test and wear surface analsis, wear behavior and its mechanism of AC2B aluminum and Al/Al$_{2}$O$_{3}$/C composites can be characterized under various sliding speed conditions. Tensile strenght elongation of Al/Al$_{2}$O$_{3}$/C composites are decreased with increasing the addition of carbon fiber. On the contrary, elastic modulus of Al/Al$_{2}$O$_{3}$/C composites is slightly improved compared with that of the unreinforced matrix alloy. The addition of carbon fiber to al/al$_{2}$O$_{3}$/C composites gives rise to improvement of the wear resistance. Specially, carbon chopped fibers play an important role in interfering sticking between the counter material and metal matirix composites. Al/Al$_{2}$O$_{3}$/C composites are suitable to high speed due to solid lubication of carbon. And wear model of Al/Al$_{2}$O$_{3}$/C composites is suggested by the examination of worn surfaces.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2003년도 춘계학술강연 및 발표대회
• /
• pp.59-59
• /
• 2003

경사기능 재료는 위치에 따른 특성 변화를 갖고 있어 변화하는 주변 환경에서 사용되는 재료의 응용성을 높일 수 있는 장점이 있다. 적합한 경사기능 재료의 제조를 위해서는 탄성률, 강도, 인성 등의 위치에 따른 변화를 예측하는 것이 필요하다. 그러나 재료 내에서의 탄성률 변화 등으로 인해 경사기능 재료에서 인성을 정량적으로 표현하는데는 어려움이 있으므로 이를 정량적으로 측정하고, R-curve를 결정하는 것은 재료의 응용성에 중요한 인자가 된다. 본 연구에서는 폴리우레탄 스폰지를 이용하여 밀도의 분포가 연속적으로 다른 폴리 우레탄 스폰지를 제조하고 이에 알루미나 분말 슬러리를 이용하여 slip casting을 행하였다. 그 후 폴리 우레탄 스폰지를 탈지한 후 알루미나 성형체를 소결하여 연속적인 기공률 분포가 다른 다공성 알루미나를 제조하였으며, 이에 Al을 용침하여 $Al_2O_3-Al$ 경사기능 재료를 제조하였다. 이러한 $Al_2O_3-Al$ 경사기능 재료에 대해 파괴인성 및 R-curve 특성을 CT(conpact tension)시편으로 측정하였으며, 이를 균일한 복합체의 파괴인성과 비교하였다. 또한 잔류 응력 특성을 파악하기 위해 실험적이 응력 데이터를 Moire interferometry를 이용하여 결정하였다. 또한 이를 유한요서 해석법(FEM)에 의한 계산치와 비교하였다. 서로 다른 조성 분포를 갖는 $Al_2O_3-Al$ 경사기능 재료와 균일한 복합체의 파괴인성을 비교한 결과 동일한 Al조성에서도 서로 다른 파괴 인성치가 나타났다. $Al_2O_3-Al$ 경사기능 재료에서 파괴인성에 영향을 줄 수 있는 인자로는 술수한 $Al_2O_3$의 파괴인성에 Al금속의 소성변형에 의한 인성증진 효과, 그리고 경사기능 재료에서 상호 조성차이에 따른 잔류응력을 고려할 수 있을 것이다. 이중 $Al_2O_3-Al$ 경사기능 재료의 파괴인성에 미치는 잔류응력의 영향을 고려하기 위해 이의 잔류응력에 대해 실험에 의한 유추된 잔류응력과 FEM계산에 의해 유추된 잔류 응력을 비교, 분석하였다.

• 한국세라믹학회지
• /
• 제56권4호
• /
• pp.350-353
• /
• 2019

Porous alumina ceramics with addition of 0, 5, 10, 15, and 20 wt% Al(H₂PO₄)₃ were sintered at 1300, 1350, and 1400℃. The effects of the Al(H₂PO₄)₃ addition on crystal phases, water absorption, open porosity, pore size distribution, microstructures, and flexural strength were studied extensively. The experimental results revealed that only characteristic peaks of corundum were indexed in the XRD patterns of the as-prepared porous ceramics. The water absorption and open porosity of the porous Al₂O₃ ceramics increased remarkably with an increase in Al(H₂PO₄)₃ addition. The flexural strength first increased to a maximum value when 5 wt% Al(H₂PO₄)₃ was added and then decreased as additional Al(H₂PO₄)₃ was further added. SEM images showed that the average Al₂O₃ grain size in the porous ceramics changed in an opposite way as the flexural strength. The porous Al₂O₃ ceramics with 10 wt% Al(H₂PO₄)₃ addition exhibited comparable flexural strength to the ceramics without Al(H₂PO₄)₃ addition, although the latter had much higher porosity.

• 한국식생활문화학회지
• /
• 제30권4호
• /
• pp.468-474
• /
• 2015

This study was designed to investigate the effects of Korean Lycii fructus water extract in Al (Aluminum) administered rats. Forty-eight male Sprague-Dawley rats were divided into six groups: Control group, water extract group with 3% Lycii fructus, 1000 and 2000 ppm of Al groups, and 1000 and 2000 ppm of Al with 3% Lycii fructus water extract group. The Al content of rat tissue in the Al administered group was lower than that in rat tissue in the Al with 3% Lycii fructus water extract group. Plasma levels of renin and aldosterone activity was higher in the Al administration group, compared with the 3% Lycii fructus water extract group and Al administered group. Aspartate amino transaminase and alanine amino transaminase activities were elevated in the Al administered group and lower in the 3% Lycii fructus water extract group. Lactate dehydrogenase was lower in the 3% Lycii fructus water extract Al group than in the Al group. Choline acetyltransferase was higher in the 3% Lycii fructus water extract Al group than in the Al group.

• 한국분말재료학회지
• /
• 제12권1호
• /
• pp.36-42
• /
• 2005

Four different mechanical alloying(MA) processes were employed to fabricate very fine intermetallic compound $Al_3Zr$ particles dispersed Al composite materials(MMC) with Al-4at.%Zr composition. Phase transformations including phase stability during MA and heat treatment processes were investigated. Part of Zr atoms were dissolved into Al matrix and part of them reacted with hydrogen produced by decomposition of PCA(methanol) to form hydride $ZrH_2$ during first MA process. These $ZrH_2$ hydrides disappeared when alloy powders were heat treated at $500^{\circC}$. Stable $Al_3Zr$ dispersoids with $DO_23$ structure were formed by heat treating the mechanically alloyed powders at $400^{\circC}$. On the other hand, metastable $Al_3Zr$dispersoids with $L1_2$ structure were formed during first MA of powers with Al-25at.%Zr composition. These metastable $Al_3Zr$ dispersoids transformed to stable $Al_3Zr$ with $DO_23$ structure when heat treated above $450^{\circC}$.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.535-543
• /
• 1997

The surface of SiC particles were partially oxidized to produce SiO2 layers on the SiC particles to prepare Al2O3/SiC composite by formation of mullite bonds between the grains of Al2O3 and SiC during sintering at 1$600^{\circ}C$. This process is considered to enable the sintering of Al2O3/SiC composite at lower temperature and also to relieve the stress, produced by thermal expansion mismatch between Al2O3 and SiC. In fact, Al2O3/SiC composite prepared by oxidation of SiC was observed to be more effectively sintered and densified at lower temperature. Maximum density, flexural strength and microhardness were obtained with 5.65 vol% of mullite content in Al2O3/SiC composite.

• 한국주조공학회지
• /
• 제13권3호
• /
• pp.285-294
• /
• 1993

Aluminum alloy 2024 matrix composites reinforced with $Al_2O_3$ particles, were prepared by rheo-compocasting, a process which consists of the incoporation distribution of reinforcement by stirring within a semi-solid alloy. The microstructures and characteristics of the interfaces have been studied using optical microscope and scanning electon microscope in 2024 aluminum alloy composites reinforced with $Al_2O_3$ particles. The main results are as follows: (1) $Al_2O_3$ particles were well distributed in composites by using rheo-compocasting. (2) As the addition of $Al_2O_3$ particle increases, the average dendrite numbers and the hardness were increased. (3) Interaction between $Al_2O_3$ particles and alloy 2024 resulted in the formation of Mg and Cu element rich region around the $Al_2O_3$ particles.