• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.61.1-61.1
• /
• 2011

본 연구에서는 Zinc Tin Oxide (ZTO)/Ag/ZTO 다층 투명 전극을 제작하고 이를 비정질 ZTO (a-ZTO) 채널을 기반으로 한 TFT에 적용하여 투명 TFT의 전기적 특성을 확인하였다. 15${\times}$15 mm 크기의 ITO (gate)/Glass 기판상에 ALD법으로 투명 $Al_2O_3$절연층을 형성하고, RF sputtering법으로 50nm 두께의 a-ZTO 채널층을 형성하였다. 열처리를 위하여 Hot plate를 이용해 대기 중에서 $300^{\circ}C$의 온도로 20분간 열처리하여 채널 특성을 최적화 하였다. 이후 투명 Source/Drain으로 ZTO/Ag/ZTO 다층 투명 전극을 DC/RF sputtering법으로 패터닝하여 투명 TFT를 완성하였고, 평가를 위해 금속 (Mo)을 Source/Drain으로 사용한 TFT를 제작하여 그 성능을 비교하였다. ZTO/Ag/ZTO 다층 투명 전극은 Ag의 삽입으로 인하여 3.96ohm/square의 매우 낮은 면저항과 $3.24{\times}10-5ohm-cm$의 비저항을 나타내었으며, Antireflection 효과에 의해 가시광선 영역 (400~600 nm)에서 86.29%의 투과율을 나타내었다. ZTO/Ag/ZTO 다층 투명 전극 기반 투명 TFT는 $6.80cm^2/V-s$의 이동도와 $8.2{\times}10^6$의 $I_{ON}/I_{OFF}$비를 나타내어 금속 Source/Drain 전극에 준하는 특성을 나타내었다. 뿐만 아니라 전체 소자의 투과도 또한 ~73.26% 수준을 나타내어 투명 TFT용 Source/Drain 전극으로서 ZTO/Ag/ZTO 다층 투명 전극의 가능성을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제18권4호
• /
• pp.406-412
• /
• 2007

An experimental study on the design of a catalytic combustor for 1.6 kW MCFC system has been performed. The roles of the catalytic combustor are to completely burn anode off-gas and to supply sufficient $CO_2$ to cathode channels. In order to avoid hot spot or fuel slippage, flow uniformity at the catalyst inlet was achieved by installing two crossing perforated plates between the catalyst and the mixing chamber with minimal pressure drop. A Pd/Ce/Ni-$Al_2O_3$ catalyst was used for complete combustion of the off-gas at GHSV=36,000.

• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.525-529
• /
• 2003

Biotribological properties, such as wear rate and friction coefficient, of 3Y-TZP and Low Temperature Degradation (LTD) free materials were investigated via a ball(SiC)-on-plate sliding wear test to evaluate the relationship between wear mechanism and phase transformation. Wear test was conducted with a sliding speed of 0.035 m/s at room temperature and at 25$0^{\circ}C$ in air under a normal load of 49 N, respectively. Although friction coefficient of 3Y-TZP was the lowest due to the fine grain size, the highest wear loss and rate were observed due to the debris of monoclinic grains introduced during sliding and their values increased drastically with raising temperature. However, the biotribological properties of LTD-free materials were insensitive to temperature due to the inertness of the phase transformation, suggesting that they may be applicable to the biomechanical parts.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.174-179
• /
• 2001

In order to investigate the fracture behaviors(perforation modes) and resistance to perforation during ballistic impact of aluminum alloy plate, ballistic tests were conducted. Depth of penetration experiments with 5.56mm-diameter ball projectile launched into 25mm-thickness Al 5052-H34 targets were conducted. A powder gun launched the 3.55g projectiles at striking velocities between 0.6 and 1.0 km/s. radiography of the damaged targets showed different penetration modes as striking velocities increased. Resistance to perforation is determined by the protection ballistic limit($V_{50}$), a statistical velocity with 50% probability for complete perforation. Fracture behaviors and ballistic tolerance, described by perforation modes, are respectfully observed at and above ballistic limit velocities, as a result of $V_{50}$ test and Projectile Through Plates (PTP) test methods. PTP tests were conducted with $0^{\circ}$ obliquity at room temperature using 5.56mm ball projectile. $V_{50}$ tests with $0^{\circ}$ obliquity at room temperature were conducted with projectiles that were able to achieve near or complete perforation during PTP tests. The effect of various impact velocity are studied with depth of penetration.

• 대한구순구개열학회지
• /
• 제14권1_2호
• /
• pp.37-44
• /
• 2011

Amniotic fluid is a complex and biological reservoir that provides mechanical cushioning and has many nutrients required for fetal growth and development. During our main research works about the fetal surgery of congenital facial defects, we reviewed several recent articles about the effectiveness and composition of amniotic fluid. Among these review processes, amniotic fluid, as the convenient medium to store sking grafts, was focused especially for its growth factors and rich nutrients, and we summarized some experimental investigations of skin grafts stored in amniotic fluid in rats. We reviewed mainly the article, "Turhan-haktanir N. et al. Histological assessment of skin grafts in amniotic fluid and saline. J Plast Surg Hand Surg 2010;44:226-30."

• 대한조선학회논문집
• /
• 제45권1호
• /
• pp.1-9
• /
• 2008

The free-surface motions interacting with structures are investigated numerically using the Moving Particle Semi-implicit (MPS) method proposed by Koshizuka et al. (1996) for solving incompressible flow. In the method, Lagrangian moving particles are used instead of Eulerian approach using grid system. Therefore the terms of time derivatives in Navier-Stokes equation can be directly calculated without any numerical diffusion or instabilities due to the fully Lagrangian treatment of fluid particles and topological failure never occur. The MPS method is applied to the numerical study on the fluid impact loads for wet-drop tests in a LNG tank, and the results are compared with experimental ones.

• 한국세라믹학회지
• /
• 제42권10호
• /
• pp.672-677
• /
• 2005

In this study we prepared the Sr-ferrite powders and magnet by a molten salt method using the (NaCl+KCl) salt mixture. Starting materials of $Fe_{2}$$O_{3}$ and Sr$Co_{3}$ were mixed as the molar ratio of 5.70:1, and 0.08 mol$ \% $ $Al_{2}$$O_{3}$, 0.10 mo1$ \% $ Si$O_{2}$ and 0.12 mo1$ \% $ CaO were added as additives. Sr-ferrite powders synthesized at the reaction temperatures of 800$\∼$1200$ ^{\circ}C $ showed the typical M-type hexagonal ferrite phase, and hexagonal plate-like morphology with uniform distribution of 1$\∼$3 $\mu$m particle size. The bulk density of the sintered Sr-ferrite magnet prepared with powders by the molten salt method showed the maximum density of 4.82 g/$cm^{3}$ at the sintering temperature of 1200$^{\circ}C $. The maxima of remanent flux density (Br, 45 emu/g) and coercive force (iHc, 3.75 kOe) occurred at the sintering temperatures of 1150$ ^{\circ}C$ and 1200$^{\circ}C $.

• International Journal of Oral Biology
• /
• 제41권2호
• /
• pp.75-81
• /
• 2016

Human mouth environment is known to include a variety bacteria, including Streptococcus spp., Staphylococcus spp., Actinomyces spp., Lactobacillus spp., Candida spp., Enterobacteriaceae, et al. Human oral microorganisms can cause dental caries, gingivitis, periodontitis, respiratory tract infection, and cardiovascular disease. Thus, right denture cleaning is essential to oral and general human health. The aim of this study was to evaluate the bactericidal effect of a sodium dichloroisocyanurate-based effervescent tablet (Aos Denti Germ, Aos Company, Chungbuk, Korea) against oral microorganisms. A total of 5 species Streptococcus spp. (Streptococcus anginosus, Streptococcus mitis, Streptococcus mutans, Streptococcus oralis, and Streptococcus sobrinus), Actinomyces oris, Candida albicans, and Escherichia coli were used in this study. All strains were exposed to the distilled water prepared with effervescent tablet. After the exposure, the mixture of strains and effervescent tablet was inoculated onto blood agar or MacConkey agar plate and cultured at $36^{\circ}C$. All strains were killed immediately on exposure to effervescent tablet. The results suggested that effervescent tablet could be used as an effective denture cleanser for dental hygiene.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1861-1868
• /
• 2001

Vortical structures in the near-wake region of a cubic obstacle are studied using numerical simulation. We consider flow between two parallel plates with a cube mounted on one of the plates. In the turbulent near-wake region of the flow, coherent structures such as hairpin vortices are found. Quasi-periodic behavior of the hairpin vortices is noticed; its dimensionless frequency at Re=1,000 is about 0.82 which is consistent with the result of Elavarasan of et al.'s experiment [Fluid Dyn. Research, 2000, 27] although their geometry is somewhat different from on. In the case of Re=3,500, the dimensionless frequency of the hairpin vortex is about 1.60. It is observed that the translating speed of the head of the hairpin vortex is lower than the streamwise mean velocity at that location. In the vicinity of the lower plate downstream of the cube, various length scales are identified thus less coherent. However, it is noticed that the vortical structures become gradually elongated downstream of the new reattachment.

• 소성∙가공
• /
• 제21권8호
• /
• pp.473-478
• /
• 2012

The yoke, a component of conventional motor-driven power steering system, often contains welding defects from its manufacturing process. To eliminate these defects, the precision cold forging process has been tried. In this study, the double-action complex forging has been used to manufacture a torsion joint yoke. The backward extrusion proved faster than the forward extrusion in forging of the product. The double-action complex forging process utilized an upper die composed of a punch, a punch guide, a disc spring and a coil spring. The forged material pushes up the punch guide, and then the disc spring and the coil spring balances the backward extrusion force. Consequently, the flow of material was essentially in the forward direction, resulting in a successful forging operation. The forging load of Al 6061-T6 was higher than that of the automotive structural hot rolled plate.