• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.392-397
• /
• 2012

In the $(La_{0.8}Ca_{0.2})(Cr_{0.9}Co_{0.1})O_3$ (LCCC), which has been using as interconnector materials in SOFC, Al ions were substituted for Co because ionic radius of Al is similar to that of Co. Because of the almost identical ionic radius of Al and Co, the substitution was not thought to be affect the tolerance factor of LCCC, and the densification behavior, high temperature electrical conductivity and thermal expansion coefficient were examined as a function of Al concentration. In the cases of the x= 0 and x= 0.02 in $(La_{0.8}Ca_{0.2})(Cr_{0.9}Co_{0.1-x}Al_x)O_3$ (x= 0~0.1), the samples showed the relative densities above ${\geq}95%$ when those were sintered at ${\geq}1,350^{\circ}C$. In the case of the $x{\geq}0.06$ the sintered density deteriorated greatly at lower sintering temperatures. High temperature electrical conductivity of the samples decreased as the content of Al increased. Since the valence state of Al ion is unchangeable, while Cr or Co ions contribute to the electrical conduction by changing those valence states, Al substitution resulted in the decreased electrical conductivity. Al doping of LCCC was an effective way of decreasing the thermal expansion coefficient (TEC).

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.460-466
• /
• 1999

The deep level electron traps in AP-MOCVD GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures have been investigated by means of Deep Level Transient Spectroscopy DLTS). In terms of the experimental procedure, GaAs/undoped Al\ulcornerGa\ulcornerAs/n-type GaAs heterostructures were deposited on 2" undoped semi-insulating GaAs wafers by the AP-MOCVD method at $650^{\circ}C$ with TMGa, AsH3, TMAl, and SiH4 gases. The n-type GaAs conduction layers were doped with Si to the target concentration of about 2$\times$10\ulcornercm\ulcorner. The Al content was targeted to x=0.5 and the thicknesses of Al\ulcornerGa\ulcornerAs layers were targeted from 0 to 40 nm. In order to investigate the electrical characteristics, an array of Schottky diodes was built on the heterostructures by the lift-off process and Al thermal evaporation. Among the key results of this experiment, the deep level electron traps at 0.742~0.777 eV and 0.359~0.680 eV were observed in the heterostructures; however, only a 0.787 eV level was detected in n-type GaAs samples without the Al\ulcornerGa\ulcornerAs overlayer. It may be concluded that the 0.787 eV level is an EL2 level and that the 0.742~0.777 eV levels are related to EL2 and residual oxygen impurities which are usually found in MOCVD GaAs and Al\ulcornerGa\ulcornerAs materials grown at $630~660^{\circ}C$. The 0.359~0.680 eV levels may be due to the defects related with the al-O complex and residual Si impurities which are also usually known to exist in the MOCVD materials. Particularly, as the Si doping concentration in the n-type GaAs layer increased, the electron trap concentrations in the heterostructure materials and the magnitude of the C-V hysteresis in the Schottky diodes also increased, indicating that all are intimately related.ated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.57.2-57.2
• /
• 2010

투명전도 산화막(Transparent conducing oxide: TCO)은 태양 전지, 터치패널, 가스 센서 등 여러 분야에 적용할 수 있는 물질로서 전기 전도성과 광 투과성을 동시에 가진다. 높은 전기 전도성과 광 투과성을 가지는 Sb:$In_2O_3$(ITO)는 투명전도 산화막 재료로써 가장 일반적으로 사용되고 있으나 인듐의 매장량 한계로 인해 가격이 높다는 단점이 있다. 본 연구에서는 ITO 대체 TCO 물질인 Al doped ZnO(AZO)를 rf magnetron sputter를 이용하여 최적의 수소 도핑량을 찾아 ITO의 전기적 광학적 성질과 비교하였다. AZO 박막은(ZnO:Al2O3 2wt.%)타겟을 이용하여 heater 온도 250도에서 슬라이드 글래스 및 코닝 글래스에 증착시켰고 비교군인 ITO박막은 (In2O3:$SnO_2$ 10wt.%)타겟을 이용하여 수소 도핑 없이 350도로 증착시켰다. AZO 및 ITO 박막의 전기적 특성은 hall measurement를 이용하여 측정하였고, UV-VIS spectrophotometer로 광학적 특성을 측정하였다. 수소 도핑량이 증가함에 따라 AZO 박막의 캐리어 농도가 증가하여 전기적 특성이 향상되었고, 가시광 영역에서 높은 평균 투과도를 유지 하였다. AZO 박막과 ITO 박막의 전기적 및 광학적 특성을 비교한 결과, 최적 수소 도핑량을 가진 AZO 박막은 ITO 박막에 준하는 특성을 보였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.306.1-306.1
• /
• 2014

정보화 시대의 발전에 따라 점점 더 많은 정보를 더욱 빠르게 처리할 수 있는 기기들이 요구되고 있다. 메모리는 그 중에서 핵심적인 부품으로써 소자의 고집적화와 고속화가 계속 진행되면서 기존의 메모리 소자들은 집적화에서 그 한계에 도달하고 있다. 기존 소자들의 집적화의 한계를 극복하기 위하여 새로운 비휘발성 메모리 소자들이 제안되었다. 그 중 resistive switching random access memory(ReRAM)은 저항의 변화특성을 사용하는 메모리로 간단한 구조를 가지고 있기 때문에 집적화에 유리하다는 장점을 가지고 있다. 그 외에도 빠른 동작 속도와 낮은 전압에서의 동작이 가능하여 차세대 메모리로써 각광받고 있는 추세이다. 본 연구실에서는 이미 nitride 물질을 기반으로 한 여러 ReRAM 소자들을 제안해 왔다. 그 중 AlN-based ReRAM 소자는 빠른 동작 속도와 좋은 내구성을 보인 바 있다. 하지만 상업화를 위해서 해결해야 할 문제점들이 아직 존재하고 있다. 대표적으로 소자의 배열에서 각 소자의 균일한 동작이 보증되어야 하기 때문에 소자의 셋/리셋 전압의 산포를 줄이고 동작 전류 레벨을 낮추어야 할 필요성이 존재한다. 이러한 ReRAM의 이슈를 해결하기 위해, 본 실험에서는 기존의 AlN-based ReRAM 소자에 Ti를 도핑 방법을 이용하여 소자의 동작 전압 및 전류의 산포를 줄이기 위한 연구를 진행 하였다. 본 실험은 co-sputtering 방법을 이용하여 Ti가 도핑된 AlN을 저항변화 물질로 사용하여 그 특성을 살펴보았다. Ti의 도핑 효과로 소자의 신뢰성 향상 및 동작 전압의 감소 등의 효과를 얻을 수 있었다. 이는 nitride 기반 물질에서 Ti dopant에 의해 형성된 TiN의 효과로 설명된다. TiN는 metallic한 특성을 지니고 있기에 저항변화물질 내에서 일종의 metallic particle의 역할을 수행할 수 있다. 따라서 conducting path의 형성과정에서 이러한 particle 들이 전계를 유도하여 좀 더 균일한 set/reset 특성을 나타내게 된다.

• Korean Journal of Materials Research
• /
• v.25 no.2
• /
• pp.107-112
• /
• 2015

The oxide films formed on etched aluminum foils play an important role as dielectric layers in aluminum electrolytic capacitors. $Y_2O_3$-doped $ZrO_2$ (YZ) films were coated on the etched aluminum foils by sol-gel dip coating, and the electrical properties of YZ-coated Al foils were characterized. YZ films annealed at $450^{\circ}C$ were crystallized into a cubic phase, and as the $Y_2O_3$ doping content increased, the unit cell of $ZrO_2$ expanded and the grain size decreased. The etch pits of Al foils were filled by YZ sol when it dried at atmospheric pressure after repeating for several times, but this step could essentially be avoided when being dried in a vacuum. YZ-coated foils indicated that the specific capacitance and dissipation factor were $2-2.5{\mu}F/cm^2$ and 2-4 at 1 kHz, respectively, and the leakage current and withstanding voltage of films approximately 200 nm thick were $5{\times}10^{-4}A$ at 21 V and 22 V, respectively. After being anodized at 500 V, the foils exhibited a specific capacitance and dissipation factor of $0.6-0.7{\mu}F/cm^2$ and 0.1-0.2, respectively, at 1 kHz, while the leakage current and withstanding voltage were $2{\times}10^{-4}-3{\times}10^{-5}A$ at 400 V and 420-450 V, respectively. This suggests that YZ film is a promising dielectric that can be used in high voltage Al electrolytic capacitors.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.301-305
• /
• 2008

An organic light-emitting diode(OLED) has advantages of low power driving, self light-emitting, wide viewing angle, excellent high resolution, full color, high reproduction, fast response speed, simple manufacturing process, or the like. However, there are still a number of challenges to get over in order to put it to practical use as a high performance display. First of all, the most important thing is to improve the efficiency of the OLED element in order to commercialize it. To this end, its efficiency can be improved by lowering the driving voltage through the improvement of structure of the OLED element and the application of new organic substance. Therefore, in this study, we have manufactured a red OLED element by applying fluorescent dyes to the emitting layer of the element having the structure of ITO/TPD/Znq2+DCJTB/Znq2/Al and the structure of ITO/CuPc/NPB/Alq3+DCJTB/Alq3/Al, in order to light-emitting various colors or improve the brightness and the efficiency, and then we have evaluated its electrical and optical characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.266.2-266.2
• /
• 2016

최근 디스플레이 산업의 확대에 따라 투명 전도 산화물(Transparent Conducting Oxides:TCOs)의 수요가 급증하고 있다. 이 중 ZnO는 wide bandgap (3.37eV)와 large exciton binding energy (60meV)의 값을 가져 차세대 투명 전도 산화물, LED와 LD 등의 소자 소재로 각광받고 있다. ZnO는 electron을 내어놓는 native defect 때문에 기본적으로 n-type 물성을 띈다. 그래서 dopant를 이용해 p-type ZnO를 제작할 때 native defect를 줄이는 것이 중요한 요점이 된다. 이 때 buffer layer를 사용하여 native defect를 줄이는 방법이 사용되고 있다. 본연구에서는 RF-magnetron sputtering법을 이용하여 c-plane sapphire 기판 위에 다양한 조건의 ZnO buffer layer를 증착하고, 그 위에 ZnO:(Al,P) co-doping한 APZO를 증착하였다. ZnO buffer layer 증착조건의 변수는 증착온도와 Ar:O2의 비율을 변수로 두었다. 이러한 박막을 FE-SEM, XRD, Hall effect measurement, AFM을 통하여 미세구조와 물성을 관찰하였다. 이 때 APZO보다 낮은 증착온도에서 ZnO buffer layer가 증착되면 APZO를 증착하는 동안 chamber 내부에서 열처리하는 효과를 얻게 되고, UHV(Ultra High Vaccum)에서 열처리 될 때 ZnO buffer layer의 mophology와 결정성이 변하게 되는 모습을 관찰아혔다. 또한 본 실험을 통해 ZnO buffer layer의 증착 온도가 APZO의 증착온도보다 높을 때 제어 가능한 실험이 됨을 확인 할 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.195-196
• /
• 2009

This paper describes the fabrication and characteristics of polycrystalline 3C-SiC thin film diodes for extreme environment applications, in which the this thin film was deposited onto oxidized Si wafers by APCVD using HMDS In this work, the optimized growth temperature and HMDS flow rate were $1,100^{\circ}C$ and 8sccm, respectively. A Schottky diode with a Au, Al/poly 3C-SiC/$SiO_2$/Si(n-type) structure was fabricated and its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) values were measured as 0.84V, over 140V, 61nm, and $2.7{\times}10^{19}cm^2$, respectively. To produce good ohmic contact, Al/3C-SiC were annealed at 300, 400, and $500^{\circ}C$ for 30min under a vacuum of $5.0{\times}10^{-6}$Torr. The obtained p-n junction diode fabricated by poly 3C-SiC had similar characteristics to a single 3C-SiC p-n junction diode.

• Journal of the Korean Applied Science and Technology
• /
• v.18 no.3
• /
• pp.186-190
• /
• 2001

By fabricating the organic light-emitting devices (OLEDs) based on phosphorescent material, the internal quantum efficiency can reach 100%, compared to 25% in the case of the fluorescent material. Thus, the phosphorescent OLEDs have recently been extensively studied and showed higher internal quantum efficiencies then the conventional OLEDs. In this study, we investigated the characteristics of the phosphorescent OLEDs, with the green emitting phosphor, $Ir(ppy)_{3}$, (tris(2-phenylpyridine)iridium). The devices with a structure of $ITO/TPD/Ir(ppy)_{3}$ doped in the host material $/BCP/Alq_{3}/Li:Al/Al$ were fabricated, and its electrical and optical characteristics were studied. By changing the doping concentration of $Ir(ppy)_{3}$, we fabricated several devices and investigated the device characteristics. OLEDs doped into BCP by 10% showed the best characteristics. For 10% doped OLEDs, the maximum luminance of was over 10000 $cd/m^{2}$, and the maximum power efficiency was 7.14 lm/W.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1445-1453
• /
• 2013

$Zn_{(1-x)}Ni_xAl_2O_4$ (x = 0.0-1.0) spinels were prepared at $800^{\circ}C$ by co-precipitation method and characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy. The specific surface area was determined by BET. SEM image showed nano sized spherical particles. XPS confirmed the valence states of the metals, showing moderate Lewis character for the surface of materials. The powders were successfully used as new heterogeneous catalysts of Biginelli's reaction, a one-pot three-component reaction, leading to some dihydropyrimidinones (DHPMs). These new catalysts that produced good yields of DHPMs, were easily recovered by simple filtration and subsequently reused with persistent activity, and they are non-toxic and environmentally friendly. The optimum amount of catalyst is 20% by weight of benzaldehyde derivatives, while the doping amount has been found optimal for x = 0.1.