• 한국분말재료학회지
• /
• 제12권6호
• /
• pp.422-427
• /
• 2005

The $Al_2O_3$ with various phases were prepared by simple ex-situ hydrolysis and spark plasma sintering (SPS) process of Al powder. The nano bayerite $(\beta-Al(OH)_3)$ phase was derived by hydrolysis of commercial powder of Al with micrometer size, whereas the bohemite (AlO(OH)) phase was obtained by hydrolysis of nano Al powder synthesized by pulsed wire evaporation (PWE) method. Compaction as well as dehydration of both nano bayerite and bohemite was carried out simultaneously by SPS method, which is used to fabricate dense powder compacts with a rapid heating rate of $100^{\circ}C$ per min. under the pressure of 50MPa. After compaction treatment in the temperature ranges from $100^{\circ}C\;to\; 1100^{\circ}C$, the bayerite and bohemite phases change into various alumina phases depending on the compaction temperatures. The bayerite shows phase transition of $Al(OH)_3{\to}{\eta}-Al_2O_3{\to}{\theta}-Al_2O_3{\to}\alpha-Al_2O_3$ sequences. On the other hand, the bohemite experiences the phase transition from AlO(OH) to ${\gamma}-Al_2O_3\;at\;350^{\circ}C.$ It shows AlO(OH) ${\gamma}-Al_2O_3{\to}{\delta}-Al_2O_3{\to}{\alpha}-Al_2O_3$ sequences. The ${\gamma}-Al_2O_3$ compacted at $550^{\circ}C$ shows a high surface area $(138m^2/g)$.

• 한국분말재료학회지
• /
• 제30권3호
• /
• pp.249-254
• /
• 2023

The influence of MgO addition on the densification and microstructure of alumina (Al₂O₃) was studied. Compacted alumina specimens were manufactured using ball-milling and one-directional pressing followed by sintering at temperatures below 1700℃. Relative density, shrinkage, hardness, and microstructure were investigated using analytical tools such as FE-SEM, EDS, and XRD. When the MgO was added up to 5.0 wt% and sintered at 1500℃ and 1600℃, the relative density exhibited an average value of 97% or more at both temperatures. The maximum density of 99.2% was with the addition of 0.5 wt% MgO at 1500℃. Meanwhile, the specimens showed significantly lower density values when sintered at 1400℃ than at 1500℃ and 1600℃ owing to the relatively low sintering temperature. The hardness and shrinkage data also showed a similar trend in the change in density, implying that the addition of approximately 0.5 wt% MgO can promote the densification of Al₂O₃. Studying the microstructure confirmed the uniformity of the sintered alumina. These results can be used as basic compositional data for the development of MgO-containing alumina as high-dielectric insulators.

• 한국환경과학회지
• /
• 제22권8호
• /
• pp.945-951
• /
• 2013

Alumina-supported catalysts containing different transition metals such as Cu, Cr, Mn, Zn, Co, W were investigated for their activity in the selective oxidation of toluene. Catalytic oxidation of toluene was investigated at atmospheric pressure in a fixed bed flow reactor system over transition metals with $Al_2O_3$ catalyst. The result showed the order of catalytic activities for the complete oxidation of toluene was Mn > Cu> Cr> Co> W> Zn for 5wt.% transition $metals/Al_2O_3$. $Mn/Al_2O_3$ catalysts containing different amount of Mn were characterized by X-ray diffraction spectroscopy for decision of loading amount of metal to alumina. 5 wt.%$Mn/Al_2O_3$ catalyst exhibits the highest catalytic activity, over which the toluene conversion was up to 90% at a temperature of $289^{\circ}C$.

• 한국세라믹학회지
• /
• 제32권9호
• /
• pp.1076-1084
• /
• 1995

A mixture of aluminum isopropoxide (Al(OC3H7i)3) solution and sodium hydroxide (NaOH) solution was hydrolyzed in the range between pH 1~14. the powder obtained from sol-gel process was calcined at several temperatures and crystallization behaviors of various samples were investigated. The hydrolyzed sols of pH 1~6 wre clear, or near clear. On the other hand, powder precipitated from sols of pH 7~14. The sample obtained from pH 3 solution crystallized via complicated route, and $\beta$-Al2O3 and $\beta$"-Al2O3 phases appeared at lower temperature than samples from other pH conditions. And the quantity of remained $\beta$"-Al2O3 phase after heat treatment at 150$0^{\circ}C$ was more than samples from other pH conditions. After sintering, ionic conductivities were 1.3$\times$10-4S.cm-1 to 0.76$\times$10-4S.cm-1.0-4S.cm-1.

• Advances in Computational Design
• /
• 제7권2호
• /
• pp.129-137
• /
• 2022

Compo-casting method is one of the popular technique to produce metal based matrix composites. But, one of the main challenges in this process is un-uniform spreading of reinforced subdivisions (particles) inside the metallic matrix and the lack of desirable mechanical properties of the final produced composites due to the low bonding strength among the metal matrix and reinforcement particles. To remove these difficulties and to promote the mechanical properties of these kind of composites, the WARM ARB technique was utilized as supplementary technique to heighten the mechanical and microstructural evolution of the casted Al/Al₂O₃ composite strips. The microstructure evolution and mechanical properties of these composites have been considered versus different WARM ARB cycles by tensile test, average Vickers micro hardness test, wear test and scanning electron microscopy (SEM). The SEM results revealed that during the higher warm- ARB cycles, big alumina clusters are broken and make a uniform distribution of alumina particles. It was shown that cumulating the forming cycles improved the mechanical properties of composites. In general, combined compo-casting and ARB process would consent making Al/Al₂O₃ composites with high consistency, good microstructural and mechanical properties.

• 한국산업융합학회 논문집
• /
• 제25권6_2호
• /
• pp.1037-1045
• /
• 2022

In this study, nanoscale Al₂O3 ceramic particles were used due its exceptionally high hardness characteristics, chemical stability, and wear resistance properties. These nanoparticles will be used to investigate the optimal process conditions for the electro co-deposition of the Ni-Al₂O₃ composite coatings. A Watts bath electrolytic solution of a controlled composition along with a fixed agitation speed was used for this study. Whereas the current density, the pH value, temperature and concentration of the nano Al₂O₃ particles of the electrolyte were designated as the manipulative variables. The experimental design method was based on the orthogonal array to find the optimum processing parameters for the electro co-deposition of Ni-Al₂O₃ composite coatings. The result of confirmation experimental based on the optimal processing condition through the analysis of variance ; EDX analysis found that the ratio of alumina increased to 8.65 wt.% and subsequently the overall hardness increased to 983 Hv. Specially, alumina were evenly distributed on Nickel matrix and particles were embedded more firmly and finely in Nickel matrix.

• 한국세라믹학회지
• /
• 제32권2호
• /
• pp.227-233
• /
• 1995

By using homestyle microwave oven, Al-Al2O3 powder mixture could be oxidized and sintered into Al2O3 body. The differences in powder characteristics among the differently processed raw materials affect the oxidation and sintering behaviours, and these effects were more pronounced in case of microwave oven than of conventional furnace. Al-Al2O3 powder mixture was oxidized and sintered within 2hrs, which could save both processing time and energy.

• 청정기술
• /
• 제18권1호
• /
• pp.63-68
• /
• 2012

본 연구에서는 베이어공정에 의해서 수산화알루미늄($Al(OH)_3$)을 합성하였으며, 고순도 알루미나를 합성하기 위하여 염산 및 초산과 같은 산성용액을 사용하여 $Al(OH)_3$에 함유된 나트륨을 제거하였다. 호주의 퀸즐랜드 주에서 생산된 보크사이트가 베이어공정에 의해 알루미나를 합성하기 위해 사용되었으며, 보크사이트는 attrition mill을 이용하여 10 ${\mu}m$ 이하의 분말로 분쇄하여 사용되었다. 보크사이트에 함유된 알루미나 성분을 용출하기 위하여 분쇄된 보크사이트를 5 N의 NaOH 수용액으로 처리하였으며, 고압반응기 내에서 보크사이트로부터 알루미나의 용출은 $140^{\circ}C$, 3.4 atm에서 수행되었다. 용출 후 고체시료인 레드 머드는 여과에 의해서 액체시료와 분리되었다. 보크사이트와 여과된 레드 머드에 함유된 알루미늄 함량과 구조변화를 XRD와 EDX로 분석하였다. 또한 분리된 용액에 함유된 알루미나는 씨드 물질로 사용된 $Al(OH)_3$의 첨가에 위해서 $Al(OH)_3$로 결정화되었다. 결정화 과정에서 얻어진 $Al(OH)_3$는 증류수에 의해서 수차례 수세과정으로 정제되었다. 또한 산성 용액에 의해서 $Al(OH)_3$에 함유된 나트륨이 제거되는 것을 확인되었다. $Al(OH)_3$ 분말의 순도는 물에 의한 세정으로 99.3%로 생산되었고, 산 처리에 의해서 나트륨의 함량은 약 0.009% 정도로 감소되었다.

• 한국세라믹학회지
• /
• 제38권8호
• /
• pp.749-754
• /
• 2001

마이크로파 추출 및 하소 공정을 통하여 카올린으로부터 베타 알루미나 전구체 및 베타 알루미나 분말을 합성하였다. 황산 알루미늄 및 가성소다의 혼합 용액을 교반되는 에탄올 용액 중에 적하시켜서 $Al_2$(SO$_4$)$_3$.17$H_2O$ 및 $Na_2$SO$_4$.10$H_2O$의 균일한 침전물을 얻었다. $\beta$- 및 $\beta$\"-Al$_2$O$_3$상으로 구성된 베타 알루미나를 얻기 위하여 재래식 및 마이크로파 하소법으로 주어진 온도에서 약 2h 동안 침전물 시료를 하소하였다. 재래식 하소된 시료에 비하여 마이크로파 하소된 시료는 $\beta$\"-Al$_2$O$_3$상이 상대적으로 많이 존재하였다. 또한, 재래식 하소된 시료와 마이크로파 하소된 시료의 미세구조는 매우 상이하였다. 매우 상이하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.51-52
• /
• 2016

This paper researches the Chloride Binding of Cement Paste according to the Ca/Si and Ca/Al Ratio. The mechanisms of chloride ion binding are not completely known, although it is believed that Alumina contents in cementitious system have an important role. For changing cement paste composition, Ordinary Portland Cement(OPC) paste is substituted by Granulated Ground Blast Slag(GGBS). With increasing the ratio of GGBS substitution(Thus alumina contents is increasing), The chloride binding capacity has a tendency to increase of binding chloride ion capacity.