• 항공우주시스템공학회지
• /
• 제5권1호
• /
• pp.17-23
• /
• 2011

Since the time, cost and lack of regulatory information and guidance, one of the largest regulatory obstacles for an airframe manufacturer of polymer based advanced composite materials in certified aircraft applications, is to generate design allowables that will satisfy Airworthiness Regulations. In the past two decades, the design allowables used in military aircraft had been generated and applied in Korea, however the qualification of composite materials used in certifying airframe structure was not accomplished for design and demonstration of compliance to applicable airworthiness regulation. It is the intend of this paper that provide the basis of composite material qualification for small aircraft certification to the airworthiness regulation.

• 대한전기학회논문지
• /
• 제32권10호
• /
• pp.367-375
• /
• 1983

미사일의 비생실험 데이타로부터 동력학적 계수를 추정하기 위하여 Extended Kalman Filter(EKF) 알고리즘을 사용하고 시뮬레이숀으로부터 얻어진 비행 데이타를 써서 알고리즘을 해석하였다. 이 알고리즘에서는 여러 가지 미사일에 적용할 수 있도록 자유도가 여섯인 (6-DOF) 운동식을 써서 미사일 모델을 세웠으며 연구결과 EKF가 비생실험후 얻어진 데이타로부터 다수의 미사일 동력학적 계수값을 추정할 수 있음을 알았다. 계수추정 알고리즘과 병행하여 미사일의 구조를 추정하는 알고리즘을 조사하였으며 이 알고리즘은 여러 후보 모델중 비행실험 데이타에 가장 근접한 값을 주는 모델을 선정한다.

• 한국항공운항학회지
• /
• 제22권3호
• /
• pp.68-73
• /
• 2014

Research is being carried out at Korea Aerospace Research Institute with aim of design a HALE UAV(High Altitude Long Endurance Unmanned Air Vehicle). HALE UAVs are ideally suited to provide surveillance, remote sensing and communication relay capabilities for both military and civilian applications. HALE UAVs typically cruise at an altitude between 15 km and 20 km, travelling at low speed and circling specific area of interest. Airframe structural point of view, weight reduction of the airframe structure is the most important method to improve the flight efficiency. High modulus CFRP(Carbon Fiber Reinforced Polymer) has been used in designing the structure in order to minimize the airframe weight. With respect to structural design and analysis, the key question is to decide an adequate airworthiness certification base to define suitable load cases for sizing of various structural components. In this study, FAR(Federal Aviation Regulation) 23 have constituted the guidance and benchmark throughout all structural studies. And the MSC/FlightLoads was introduced to analyze the flight loads for the HALE UAV. The MSC/FlightLoads can compute the flexible air load and analyzed loads are distributed on structural model directly. A preliminary structural concept was defined in accordance with the estimated inertial and aerodynamic loads. A FEM analysis was carried out using the MSC/Nastran code to predict the static and dynamic behaviour of UAV structure.

• 한국재료학회지
• /
• 제25권10호
• /
• pp.516-522
• /
• 2015

Aging aircraft structures are inevitably exposed to environment for a long time facing many potential problems, including corrosion and wide spread fatigue damage, which in turn cause the degradation of flight safety. In this study, the environmental surface damages on aging aircraft structures induced during service were quantitatively analyzed. Additionally, S-N fatigue tests were performed with center hole specimens extracted from aging aircraft structures. From the results of quantitative analyses of the surface damages and fatigue tests, it is concluded that corrosion pits initiated during service reduce the fatigue life significantly. Finally, using the fracture mechanics and the EIFS (equivalent initial flaw size) concepts, the remaining fatigue life was predicted based on actual fatigue test results.

• International Journal of Aeronautical and Space Sciences
• /
• 제16권1호
• /
• pp.41-49
• /
• 2015

Analysis and test of hydrodynamic ram in welded metallic tanks containing water were performed to investigate the phenomena and to understand the effects on the resulting structural behavior. Arbitrary Lagrange-Euler coupling method was used for the analysis of the fluid-structure interaction occurring in the hydrodynamic ram, where the projectile, tank, and water are exchanging load, momentum, and energy during the traveling of the projectile through the water of the tank. For a better representation of the physical phenomena, modeling of the welded edges is added to the analysis to simulate the earlier weld line fracture and its influence on the resulting hydrodynamic ram behavior. Corresponding hydrodynamic tests were performed in a modified gas gun facility, and the following panel-based examinations of various parameters, such as displacement, velocity, stress, and energy, as well as hydrodynamic ram pressure show that the analysis and test are well correlated, and thus the results of the study reasonably explain the characteristics of the hydrodynamic ram. The methodology and procedures of the present study are applicable to the hydrodynamic ram assessment of airframe survivability design concepts.

• 한국항공우주학회지
• /
• 제37권1호
• /
• pp.105-112
• /
• 2009

전투기가 임무수행중 기체에 발생할 수 있는 전투손상에 대처하기 위해 손상평가 및 수리설계, 구조건전성 평가방법 등 손상 후속절차를 연구하였다. 사례로서 F-15 ECS Bay에 발생한 전투손상에 대하여 ABDR(Aircraft Battle Damage Repair) 기술을 적용하여 손상평가 및 수리설계를 수행하고, 그 내용과 절차를 양식에 정리하였다. 또한, 정적강도 및 피로수명 계산과 같이 수리설계 구조의 구조건전성을 평가하여 비행안전 여부를 입증하고 영구수리 시점을 판단하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.497-501
• /
• 2008

To improve occupants' safety in an emergency, crashworthy design is necessary to rotorcraft design and development. To improve crashworthiness capability, most of the crash energy should be absorbed by rotorcraft and the energy transmitted to the occupants should be minimized. To absorb the crash energy efficiently, the individual energy attenuation provided by landing gear, structure, fuel tank and seats should be considered totally. Especially, landing gear has the important role for crashworthy design because landing gear absorbs relatively large energy for the crash landing. In addition, military specifications require failure of landing gear shall not increase danger to any occupants by penetration of the airframe. To meet the specification requirements, failure mechanism should be prepared so that landing gear is collapsed safely and doesn't penetrate the airframe. In this study, design of failure mechanism which is necessary for the rotorcraft landing gear was performed and the results were presented.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권2호
• /
• pp.67-75
• /
• 2002

In the course of missile system design, jet plume impingement is encountered in designing airframe as well as launchers, requiring careful investigation of its effect on the system. In the present paper, recent works on such topic are presented to demonstrate usefulness of CFD results in helping design the hardware. The jet impinging flow structure exhibits such complex nature as shock shell, plate shock and Mach disk depending on the flow parameters. The main parameters are the ratio of the jet pressure to the ambient pressure and the distance between the nozzle and the wall. In the current application, the nozzle contour and the pressure ratio are held fixed, but the jet impinging distance is varied to illuminate the characteristics of the jet plume with the distance. The same methodology is then applied to a complex vertical launcher system (VLS), capturing its flow structure and major design parameter. These applications involving jets are thus hoped to demonstrate the usefulness and value of CFD in designing a complex structure in the real engineering environment.

• 한국항공운항학회지
• /
• 제21권1호
• /
• pp.62-67
• /
• 2013

Human Powered Aircraft (HPA) should be light in weight and have high efficiency because power source of propulsion is human muscles. Airframe structure takes up most of empty weight of aircraft, so weight reduction of structure is very important issue for HPA. In this paper, design/analysis/test procedures for ultra light weight structure of the HPA developed by Korea Aerospace Research Institute (KARI) are explained briefly. Structural design is conducted through case studies on HPA in the USA and Japan. Loads analysis is performed to calculate design loads which is needed for structural design and analysis. Structural analysis is conducted for structure sizing. Static strength test of main wing spar which is primary structure of wing is performed to verify structural integrity.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 추계학술대회논문집
• /
• pp.105-112
• /
• 1996

Aluminium alloy have been used extensively as forging materials for aircraft components due to their high specific strength and corrosion resistance. A large portions of these materials are used as airframe components consisted of various combination of such Rib-Web structure. But the problem of high forging pressure and defect which were caused by narrow Rib thickness prevented from the favorable developments and laboratory scaled trials. In this study, optimization of forging variables such as corner radius and temperature in Rib-Wed structure were established. The 2 mm of corner radius minimized the forging pressure to get the fixed Rib height, which well coincided with theoretical result according to Upper-Bound analysis. And optimum workpiece temperature was below 450$^{\circ}C$ in consideration of grain growth and forging defects by local melting.