• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.521-526
• /
• 2014

현대에 이르러 초경량 무인 비행기에 대한 많은 연구가 진행되고 있다. 이러한 비행체는 저레이놀즈수 영역에서 사용되는 특성으로 인해, 경계층 내에서 박리현상과 난류영역으로의 천이 등과 같은 여러 복합적인 현상을 발생시킴으로써 비행체의 공력특성에 큰 영향을 미친다. Bumpy Airfoil은 저레이놀즈수 유동에서의 이와 같은 문제를 해결하기 위해 제안된 익형이다. 따라서 본 논문은 전산열유체해석 프로그램인 EDISON_전산열유체를 이용하여 Bumpy Airfoil 형상에 대한 공력특성을 연구하였고, 발생하는 양항비를 원 익형과 비교하였다. 비압축성 조건 내에서, 공력 성능 향상을 위한 Bumpy Airfoil의 형상 변수로 Bump 개수와 높이를 선정하여 받음각에 따른 유동장을 분석하고 양항비를 수치해석 및 고찰하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.139-145
• /
• 2012

The low speed aerodynamic characteristics of modified sonic arc airfoil which is developed to fit the transonic regime are investigated. This airfoil is designed by using the shape function of sonic arc proposed by Schwendenman, the data of NACA0012, and commercial program Maple. In order to investigate the low speed aerodynamic characteristic of sonic arc airfoil, the numerical analysis is conducted below Mach number 0.3 and the results are compared and analyzed with it of NACA0012 airfoil. At each Mach number, the drag of modified sonic arc airfoil is less 1.5% than NACA0012's drag and the lift of modified sonic arc airfoil is less 2% than NACA0012's lift. The moment coefficient of modified sonic arc airfoil is also less 1.4% than it of NACA0012 at each Mach number.

• Wind and Structures
• /
• v.37 no.1
• /
• pp.15-23
• /
• 2023

The wake behavior of extended flat plate and serration in the trailing edge of S809 airfoil is presented in this experimental study using wind tunnel testing. The clustering of wind turbines in wind parks has recently been a pressing issue, due to the expected increase in power output and deciding the number of wind turbines to be installed. One of the prominent factors which influence the performance of the subsequent wind turbines is the downstream wake characteristics. A series of wind tunnel investigations were performed to assess the downstream near wake characteristics of the S809 airfoil at various angles of attack corresponding to the Reynolds Number Re = 2.02 × 105. These experimental results revealed the complex nature of the downstream near wake characteristics featuring substantial asymmetry arising out of the incoherent flow separations prevailing over the suction and the pressure sides of the airfoil. Based on the experimental results, it is found that the wake width and the downstream velocity ratio decrease with an increase in the angle of attack. Nonetheless, the dissipation length and downstream velocity ratio increases proportionally in the downstream direction. Additionally, attempts were made to understand the physical nature of the near wake characteristics at 1C, 2C, 3C and 4C downstream locations.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.9-12
• /
• 2012

현재 각 나라에서 고고도 무인항공기에 대한 관심이 높아지고, 우리나라 또한 여러 가지 형상의 고고도 무인항공기를 개발하기위해 노력하고 있다. 본 연구에서는 고고도 무인항공기에 사용되는 에어포일의 공력특성을 EDISON_CFD를 이용하여 분석하였다. 현재 개발된 고고도 무인항공기 중 글로벌 호크를 선정하여 그 주 날개의 Airfoil을 해석모델로 선정하고 항공기 운항시 고도 조건을 적용하여 공력특성을 분석하였다. 받음각의 범위는 $2^{\circ}{\sim}10^{\circ}$로 설정하였고 $C_l$ 및 $C_d$ 값을 계산하여 공력 특성 곡선($C_l$, $C_d$, $C_d-C_l$)을 구성하였다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.925-931
• /
• 2016

The BLDC motor is used widely in industry due to its controllability and freedom from maintenance because there is no mechanical brush in the BLDC motor. Furthermore, it is suitable for high-speed applications, such as compressors and air blowers. For instance, for a compressor with a small impeller due to miniaturizing, the BLDC motor has to rotate at a very high speed to maintain the compression ratio of the compressor. Typically, to reach an ultra-high speed, airfoil bearings must be used in place of ball bearings because of their friction. Unfortunately, the characteristics of airfoil bearings change drastically depending on the revolution speed. In this paper, a BLDC motor with airfoil bearings is controlled with a PID controller. To analyze and determine the PID coefficients, the relay-feedback method is used. Additionally, for adaptive control, a fuzzy logic controller is used. Furthermore, the auto-tuning and self-tuning techniques are combined to control the BLDC motor. The proposed method is able to control the airfoil-bearing BLDC motor efficiently.

• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.3
• /
• pp.317-322
• /
• 2012

The low speed aerodynamic characteristics for a modified sonic arc airfoil which is designed by using the nose shape function of sonic arc, the shape function of NACA four-digit wing sections, and Maple are experimentally investigated. The small rotor blades of a modified sonic arc and NACA0012 airfoil are precisely fabricated with a commercially available light aluminum(Al 6061-T6) and are spin tested over a low speed range (3000rpm-5000rpm). In a consuming power comparison, the consuming powers of NACA0012 are higher than that of modified sonic arcs at each pitch angle. The measured rotor thrust for each pitch angle is used to estimate the rotor thrust coefficient according to momentum theory in the hover state. The value of thrust coefficients for both two airfoils at each pitch angle show almost constant values over the low Mach number range. However, the rotor thrust coefficient of NACA0012 is higher than that of the modified sonic arc at each pitch angle. In conclusion, the aerodynamic performance of NACA0012 is better than that of modified sonic arcs in the low speed regime. This test model will provide a convenient platform for improving the aerodynamic performance of small scale airfoils and for performing design optimization studies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.2
• /
• pp.99-107
• /
• 2014

In this study, aerodynamic characteristics of Kline-Fogleman airfoils are numerically investigatied which has been widely used in remote control aircraft operating at low Reynolds numbers. The comparison of aerodynamic characteristics was conducted between NACA4415 and Kline-Fogleman airfoil based on NACA4415. ANSYS Fluent was employed with the incompressible assumption and $k-{\omega}$ SST turbulence model. It was found that lift coefficient was significantly enhanced in the range of Reynolds number from $3{\times}10^3$ to $3{\times}10^6$. Especially in the region of Reynolds number below $2.4{\times}10^5$, the lift-to-drag-ratio was improved by 26% using the Kline-Folgeman airfoil compared with NACA4415 airfoil.

• Journal of Wind Energy
• /
• v.5 no.1
• /
• pp.33-42
• /
• 2014

The new aerofoil, KA2 was designed to apply to the wind turbine blade. For the aerofoil, numerical analysis was performed to review aerodynamic characteristics like lift and drag coefficient. And they are verified with test data using the digital wind tunnel and test samples from 3D printer. The digital wind tunnel was developed to test wing in the small laboratory, and verified with test of NACA0012 airfoil. KA2 aerofoil is asymmetric, and has the thickness ratio of 14%, and 12 degree of AOA at the maximum lift coefficient of 1.3. In this paper, aerodynamic characteristics from numerical and test approaches will be proposed with AOA in detail. Therefore, this aerofoil will be used for the design of wind turbine blade.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.475-484
• /
• 2012

Numerical investigation is performed to understand the effects of thickness uncertainty of a supporting airfoil due to manufacturing processes on the aerodynamic characteristics of an airfoil used for measuring data in a wind tunnel testing. This is done by comparing the coefficients of lift, drag and moment of the airfoils. In this work, the airfoil model consists of three parts, one located in the center for measuring and two outer parts used for supporting. The study is carried out with a NACA64-418 airfoil and the turbulence model of Transition SST. It is found that the effect of thickness uncertainty of the airfoils used for supporting is not significant to the performance of the test airfoil at various angles of attack and Reynolds numbers.

• Journal of computational fluids engineering
• /
• v.19 no.4
• /
• pp.94-99
• /
• 2014

The aerodynamic performance of a modified NACA64-418 with blunt trailing edges of irregular shape was investigated. As the trailing edge of the airfoil was thickened, the drag of the airfoil was increased due to development of a re-circulation bubble in the wake region. To reduce the drag of the airfoil with a blunt trailing edge, the optimum shape of the trailing edge for a modified NACA64-418 was investigated. The numerical results showed that the drag of the protruding shape was much more decreased than that of the retreating shape, but the lift was almost the same regardless of shape. In addition, the pitching moment of the modified NACA64-418 with a protruding sharp trailing edge was the smallest at the given angle of attack.