• Journal of computational fluids engineering
• /
• v.3 no.2
• /
• pp.52-64
• /
• 1998

Numerical simulations on the flowfield of lifting chamber for Wing-In-Ground vehicle were performed using Fluent/UNS 4.2 software. The trend of lifting force in lifting chamber and parametric study of geometric and fluid variables were primarily investigated. Selected parameters for investigation are inlet velocity, height between chamber and water level, depth of the skirt, location of inlet, variaton of height at bow and stern. Also, air capturing capabilities from downstream of the propeller were evaluated at the air inlet. The lifting force was increased linearly with the increased of inlet velocity and nonlinearly with the decrease of height force was increased with increased depth. It turned out to have very minor effect on lifting force to change the location of air inlet for lifting chamber, installed on top surface. Tilting the vehicle when it was lifted, the lifting forces, generated in each case, showed no appreciable changes.

• Journal of the Ergonomics Society of Korea
• /
• v.21 no.1
• /
• pp.27-32
• /
• 2002

The objective of this study was to investigate the effects of fatigue, caused by frequent manual lifting. on lifting velocity and lifting acceleration. Ten male volunteers performed lifting at a rate of 4 times per minute, continuously, for two hours using the free-style posture A box($30cm{\times}30cm{\times}20$) with a fixed weight (15.9 Kg) was used as the load for lifting, Heart rate, oxygen consumption, and EMG were also measured to estimate the level of fatigue, The posture as well as acceleration was recorded. The results showed that the lifting acceleration at the end of two hour increased significantly (20%, p<0.001) compared to the acceleration after fifteen minutes of lifting. It was also found that subjects changed their lifting postures as the result of fatigue. All subjects also indicated pain in their upper legs and the lower back at the conclusion of the experiment.

• Proceedings of the ESK Conference
• /
• 1992.10a
• /
• pp.18-21
• /
• 1992

The objective of this study was to investigate the effects of fatigue, caused by frequent manual lifting, on lifting velocity and lifting acceleration. Ten male volunteers performed lifting at a rate of 4 times per minute, continuously, for two hours using the free-style posture. A box $(30cm{\times}30cm{\times}20cm)$ with a fixed weight (15.9kg) was used as the load for lifting. Heart rate, oxygen consumption, and EMG were also measured to estimate the level of fatigue. The posture as well as acceleration was recorded. The results show that the lifting acceleration at the end of two hour increased significantly (20%, p<0.001) compared to the accleration after fifteen minutes of lifting. It was also found that subjects changed their lifting postures as the result of fatigue. All subjects also indicated pain in their upper legs and the lower back at the conclusion of the experiment.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.251-255
• /
• 2002

Eutrophic matters accumulated on the bottom of sea, river and lake cause red tide phenomenon in ocean and outbreak green algae in river and lake. Systems are developed to remove the noxious deposit. But the existing systems remove not only the eutrophic matters but also natural materials, sand, pebbles etc. that should remain at the bottom. This paper describes a new system that can safely, and economically take away the noxious deposit in underwater. High pressure water jet is used to induce vortices in the triangular suction section, and air-lifting pump to lift up the deposit. The mixture of the water and deposit is filtered through the drum filters. An under camera shows the under water situation along the moving direction of the system that is controlled by a remote operator. This remote controlled moving system obliterate the necessity of the diver that usually costs high. The experimental results show the effectiveness of the suggested system.

• Ocean Systems Engineering
• /
• v.5 no.3
• /
• pp.181-198
• /
• 2015

An OSV (Offshore Support Vessel) is being used to install a structure which is laid on its deck or an adjacent transport barge by lifting off the structure with its own crane, lifting in the air, crossing splash zone, deeply submerging, and lastly landing it. There are some major considerations during these operations. Especially, when lifting off the structure, if operating conditions such as ocean environmental loads and lifting off velocity are not suitable, the collision can be occurred due to the relative motion between the structure and the OSV or the transport barge. To solve this problem, this study performs the physics-based simulation of the lifting off step while the OSV installs the structure. The simulation includes the calculation of dynamic responses of the OSV and the structure, including the collision detection between the transport barge and the structure. To check the applicability of the physics-based simulation, it is applied to a problem of the lifting off step by varying the ocean environmental loads and the lifting off velocity. As a result, it is confirmed that the operability of the lifting off step are affected by the conditions.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1753-1764
• /
• 2006

A U-80 propeller and its modified version, U-75 propeller, are used for a micro air vehicle. The performance characteristics of a U-80 propeller and a U-75 propeller have not much known in the published literature. Thus, their aerodynamic characteristics are investigated using a lifting surface numerical method. The lifting surface method is validated by comparing computed results with measured data in a wind tunnel. From the computed results, it is found that the U-75 propeller produces larger thrust with higher efficiency than the U-80 propeller. To enhance the performance of these propellers, a new propeller is designed by following the sequential design procedures with the design parameters such as hub-tip ratio, maximum camber and its position, and chord length distribution along the radial direction. The performance of the designed propeller is shown to be improved much comparing with those of both the U-80 and U-75 propellers.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.56.1-56.1
• /
• 2008

• Journal of the Korean Society of Combustion
• /
• v.4 no.1
• /
• pp.49-57
• /
• 1999

An experimental study on double-concentric diffusion flame has been carried out in order to investigate the shape, the flame length, and the other characteristics of the flame. Flow visualization of the flame by the $TiO_2$ particles and also the emission measurements are conducted. The commercial grade LP gases are used as fuel. The inverse diffusion flames are formed at the center when the central air flow rate is about 0.1 L/min. With a larger flow rate of the central air jet than 0.2 L/min the flame turns to be an annular-shaped flame, which is very bright. When the central air flow rate increases over 2.4 L/min, the flame turns to blue and the flame tips are opened because of the lifting of the inner part of the flame. Because of this lifting and the incomplete combustion, the CO emission increases abruptly from 25 ppm to more than 150 ppm. On the contrary, the NOx emission is decreased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.145-146
• /
• 2018

This study was performed to develop the lifting pallets for the application of smart skin system when remodeling the balcony of apartment house. For this purpose, the smart skin system based on IoT, combining window, BIPV, ESS, air purifier applied in this study was examined. The study developed and presented a foldable double pallet considering the load (about 2Ton) and specification (width 7m × height 2.6m × width 1.3m) of the smart skin system. In future research, it is necessary to verify the application of the foldable pallet in this study.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.424-424
• /
• 2000

The implementation of a insect-based flying microrobot has been previously proposed as using magnetic force. The flying principle of a butterfly is different from that of a airplane, which obtain lifting force above the wings by a air stream with low pressure. Butterflies obtain lifting force below the wings by flapping. They can fly when drag during the down stroke is greater that during the up stroke. The structure of flying microrobot must satisfy these condition. And that must be manufacture lightly and keep balance for rising to the air sufficiently. Moreover the efficiency of an electromagnet is high and the flux density is sustained uniformly and widely Nevertheless these condition is satisfied, the implementation of a flying microrobot is very difficult as the flying microrobot has to fly without guides or sensor. We propose differently a new model il] comparison with that other paper has suggested. This imitates the form of the Korean shield-shaped kite.