• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.4
• /
• pp.472-483
• /
• 1997

An experimental facility consisting of two $3{\times}4.4{\times}3.8m$ rooms identical in construction is built. Each room has a control system and storage tank supplying hot water to the radiant floor heating system. The facility enables simultaneous comparision of two different control stratigies each implemented in a separate room. The operating performance of three kinds of flow control scheme is tested and compared in this study : (i) conventional on-off control based on feedback from room air temperature (ii) TPSC(two parameter switching control) (iii) TPOC(two parameter on-off control). Results show that TPSC and TPOC using room air and surface temperature sequentially as feedback signal to control hot water supply is the better temperature regulation scheme than conventional control based on feedback from only room air temperature. They are good candidates for the room with radiant floor heating system under continuous and intermittent heating mode.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.6
• /
• pp.257-262
• /
• 2014

This paper describes an experimental study for heating performance that can be used in R-134a automobile heat pump systems. The heat pump system is widely studied for heating system in zero-emission vehicles to attain both the small power consumption and the effective heating of the cabin. This paper presents the experimental results of the influence on heating capacity and coefficient of performance of heat pump system. Tests were performed with different sizes of internal and external heat exchangers, and refrigerant flow rate was also considered in two-way flow devices. In addition, the heat, air, and water sources with the heat pump system were examined. The experimental results with the heat pump system were used to analyze the impact on performances. The best combination of performance was A-inside heat exchanger, B-outside heat exchanger, and B-flow device, respectively. In addition, a water heat-source was found to give roughly 40% of better performance than an air heat-source heat pump system.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.385-390
• /
• 2000

The heat pump is one of heating and cooling systems driven by electricity using natural energy as a heat source. The heat pump system was mainly adopted to a cooling system or a refrigeration system. In regions with a large amount of electricity, it is used as a heating system or a heating and cooling system of houses, buildings and agricultural facilities. During cold weather, air source heat pumps do not work well because of some technical problems, such as frosting on evaporator coil when outside air temperature is below -5$^{\circ}C$. In this research, the heat regenerative technology was employed to eliminate the frosting on evaporator coil and improve the COP of the heat pump system. This fiber belt heat regeneration system(FBHRS) has very simple structure consisting of a geared motor and a porous fiber belt passing through alternatively between cold and warm air duct. The laboratory test showed that the heat pump system with a FBHRS yielded an impressive COP higher than 3.5 at the outside air temperature of -7$^{\circ}C$ in heating mode.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.52-60
• /
• 1997

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split- resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent, wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heat ed f or 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• v.11 no.2
• /
• pp.52-60
• /
• 1983

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split-resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent-wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heated for 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.2
• /
• pp.69-74
• /
• 2016

Most hot water heating valves for apartments are constant-flow types, which limit the flow rate through an individual household for even distribution of heating water to other households. The constant-flow type is implemented by an on-off control. As a result, heating water is supplied intermittently and hence, indoor air temperature also fluctuates. Returning water temperature is also high, which reduces energy efficiency. To implement continuous feedback control, the indoor temperature dynamics was simulated to fit a measured temperature history by a state-of-the-art physical model. From the model, it was found that the most important disturbance is outdoor temperature and its effect on indoor temperature lasts about an hour. To cope with the slow response and the significant disturbance, a prediction control with proportional feedback is proposed. The control was found to be successful in implementing continuous heating water flow and improved indoor temperature control.

• Journal of Biosystems Engineering
• /
• v.24 no.6
• /
• pp.501-512
• /
• 1999

In this study, the coefficient of performance of a vapour compression heat pump system was analyzed for the evaluation of the heat pump performance. A water-to-air heat pump was assembled and tested by changing the level of the compressor driving speed and the air mass flow rate during air heating process. The coefficient of performance for air heating was 2.6~3.8 and that for water cooling was 1.0~1.4. The coefficient of performance was not depending on the levels of the compressor driving speed or levels of the air mass flow rate, but on the temperature of the air and water. The coefficient of performance for air heating increased by about 0.2 with the water temperature increasing by 1$^{\circ}C$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.2
• /
• pp.144-150
• /
• 2006

The purpose of this study is to predict outlet temperature and humidity through underground pit for the reduction of cooling load and heating load. Commonly, the underground temperature is lower than outdoor in summer but the reverse happens in winter. When the outdoor average air temperature is $25.7^{\circ}C$ during cooling periods, the average outlet air temperature through underground pit is $23.6^{\circ}C$ with 3 m-depth and 60m-length and is $22.2^{\circ}C$ with 3 m-depth and 150 m-length. When the outdoor average air temperature is $4.9^{\circ}C$ during heating periods, the average outlet air temperature through underground pit is $7.7^{\circ}C$ with 3m-depth and 60 m-length and is $10.8^{\circ}C$ with 3 m-depth and 150 m-length. The outlet air temperature is affected by more length than depth of underground pit. The diffusion ratio of outdoor humidity is $-7.7\times10^{-8}kg/s$ in cooling periods and $9.29\times10^{-7}kg/s$ in heating periods.

• Solar Energy
• /
• v.20 no.4
• /
• pp.1-8
• /
• 2000

The suggested year round solar air conditioning system has been developed for cooling and heating. In particular, this system focused on cooling and dehumidification and it could reduce a peak time owing to the use of air conditioners in summer. This study was performed to find out how much heating loads could be saved and furthermore whether this suggested system would be possible to do heating without a switch of system in real situations. Through model house experiments, the following conclusions were obtained. 1) The collector efficiency was 36% at maximum, but more improved structure of suggested collector could increase its efficiency. 2) The temperature of outlet air was about $30^{\circ}C$ and it could reduce heating loads. 3) Measured temperature and calculated one agreed well within ${\pm}1.5^{\circ}C$.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.71-76
• /
• 2011

Earth to air heat exchangers made by iron, aluminium, copper and poly-ethylene pipe for single greenhouse heating were experimented and blowers. Earth to air heat exchanger was installed by pipelines in earth tube at 70cm depths and air blower was the heating capacity 3kW/h, As the result, Temperature difference due to temperature history of the inlet and outlet air on the various type in earth tube in greenhouse showed that air temperature at the various type in earth tube, comparison tube were make no difference respectively. Under the experimental condition, heat fluxes and heating load were showed 6,800Kcal/h, 19,699kcal/h generally yield of Lactuca Sativa cultured during days of sowing 90day in greenhouse using copper pipe was 170% incleased.