• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.70-83
• /
• 1997

We made a selection of engine operating conditions in the natural aspiration type diesel engine as load and speed. The effects on the power, smoke emission and cylinder pressure characteristics of these variations in operating conditions were observed experimentally. Also, the smoke emission was predicted by using the Arrhenius equation and empirical equation of the smoke emission was made. At the same time, the correlations, between the combustion and smoke emission characteristic were examined. From the above results, it is clear that to prevent power dropping and to decrease exhaust fume whin the conditions are changed, one should improve the intake system. To do this, the best way is to lower the air-fuel mixing ratio. We found that the parameters of the indicated mean effective pressure, maximum pressure and its location and combustion duration, etc. change the motion in accordance with the conditions described above. Also, we found that the variation of the pressure cycle comes from an amplified variation of the early part of process. From the analysis of comparing combustion and exhaust fume, the exhaust fume is produced at the latter time of combustion and decreased when the combustion ratio is higher. Also, we developed a special formula which can predict the exhaust fume value according to the engine load and speed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.584-587
• /
• 2011

마하 5 스크램젯 엔진에 대하여 연소 시험에 대한 예비 시험 성격으로서 연료 분사 없이 내부 유동 공력 시험을 수행하였다. 엔진은 흡입구 크기 $70mm{\times}200mm$, 전체 길이 1.7m의 시험용 모델을 대상으로 하였다. 설비는 한국항공우주연구원이 자체 설계 개발하여 보유한 불어내기식 극초음속 시험 설비를 사용하였다. 측정은 엔진 내부 유로를 따라 19개 지점에서 압력을 측정하였다. 시험 결과 본 엔진 모델을 사용하여 설비 시동이 가능하였으며 엔진 내부는 초음속 유동이 유지됨을 확인하였다.

• 한국가시화정보학회지
• /
• 제10권2호
• /
• pp.20-24
• /
• 2012

Increasing the active catalyst surface area is important in improving a converter's efficiency. In addition, uniform flow is advantageous in that it produces more efficient catalytic conversion. This results in the ability to use a smaller catalytic converter with uniform flow as opposed to a larger converter requirement for non-uniform flow. Therefore, it is important to characterize the internal flow of the catalytic converter. To characterize the system's flow patterns, velocity measurements were taken at the mid and exit planes of a ceramic honeycomb catalytic converter at flow rates of 37.8 l/s and 94.4 l/s. Measurements were conducted using LDV. The profiles were measured along both the major and minor axis of the planes. Primary flow direction velocities measured along the minor axis, at both flow rates, varied greatly at the mid plane and somewhat at the exit plane. The areas of greatest air flow were seen near the edges of the walls and on the side of the converter opposite the flow's entrance region. It also appears that the high velocities opposite the intake are due to the design of the entrance region. The entrance region is possibly too small to properly redirect the vertically entering fluid into an evenly distributed flow in the primary flow direction.

• Asian-Australasian Journal of Animal Sciences
• /
• 제9권5호
• /
• pp.603-610
• /
• 1996

Spatial distribution of faeces by Japanese Black heifers and steers was investigated. The animals grazed a bahiagrass (Paspalum notatum $Fl\ddot{u}gge$) pasture in the daytime from 9 a.m. to 4 p.m., and spent the rest of the day in a barn. The pasture consisted of three paddocks, an alley and a resting area, and the paddocks were grazed rotationally. The number of defecations and the faecal weight excreted in the pasture were greater than those expected from the proportion of time that the animals spent in the pasture. These values were correspondingly smaller in the barn. The distribution of faeces to the paddock, alley and resting area of the pasture was usually not proportional to the area of the respective places. The number of defeations and the faecal weight were usually distributed less densely in the paddock than in the resting area. The degree of aggregation of defecation in the paddock, alley and resting area varied with the meteorological factors such as the air temperature, solar radiation and rainfall during the grazing, and the intake of hay supplement of the previous day.

• 대한기계학회논문집B
• /
• 제22권11호
• /
• pp.1530-1537
• /
• 1998

Mixture formation is one of the significant factors to improve combustion performance of an spark ignition engine. This is affected by spray and atomization characteristics of injector. In the case of EGI system, air-fuel mixing period is so short that a lot of fuel-film and liquid-fuel flow into cylinder. Since this fuel-film is not burnt perfectly in cylinder, it is exhausted in the form of HC emission. In this paper, three measurement techniques were utilized to measure spray characteristics and the amount of fuel-film in the cylinder. At first, PMAS was used to measure the spray characteristics such as size distributions, SMD, and spray angle. Secondly the amount and distribution of fuel-film which flow into through intake valve could be measured quantitatively using the fuel-film measuring device. And lastly, by optical fiber type spark plug used to detect the diffusion flame, the amount of unburned HC was measured. As the result of these experiments, the information of optimal spray characteristics and injection condition to minimize fuel-film could be built up.

• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.129-134
• /
• 2010

A diesel engine is equipped with a turbocharger for providing more power at a low engine speed region by supplying charge air to combustion chambers. The turbocharger makes it possible to satisfy stringent emission regulations and customers' demand of enjoying the fun to drive by increasing engine performance. However, the turbocharger has the disadvantage of making BPF(Blade Passing Frequency), hissing, surge, whistle, and blow noises. Among them, reducing the blow noise, a narrow-band noise(a general range : 1800~2000Hz), is possible by using a resonator that controls the narrow frequency band governing the resonance in the intake system. In this study, the optimum location of the resonator is found by employing Boost as a CAE(Computer Aided Engineering) tool and is confirmed by experiments of an engine dynamo test and a real vehicle test.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.64-74
• /
• 2005

The effect of fuel injection spray on engine performance has been known as one of the major concerns for improving fuel economy and reducing emissions. In general, reducing the spray droplet size could prevent HC emission in gasoline engine. As far as PFI gasoline engine is concerned, the mixture of air and fuel may not be uniform under a certain condition, because breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve. This study, by constituting PFI gasoline spray system, was performed to study the transient spray characteristics and dynamic behavior of droplets from two-holes two-sprays type injector used in DOHC gasoline engine. Mean droplet size and optical concentration in accordance with various conditions were measured by LDPA and CCD camera. Through this study, the variation of drop size and optical concentration could be used for understanding the behavior of unsteady spray was declared and the existing the small droplets between each pulse spray could be estimated caused to the development of wall film was conformed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.3102-3107
• /
• 2008

This paper was focused on the particulate matter (PM) on the gasoline and bio ethanol. Bio ethanol as a clean fuel is considered one of the alternative fuels that decreased the PM emission from the vehicle. Particle formation in SI engine was depended on the fuel and engine operating condition. In this paper, Particle number concentration behaviors were analyzed by DMS500 (Differential Mobility Spectrometer) and CPC (Condensation Particle Counter) instrument which was recommended by PMP (Particle Measurement Programme). Particle emissions were measured with various engine operating variables such as air excess ratio ($\lambda$), spark timing and intake valve opening (IVO) at part load condition. In vehicle test, the number of particulate matter was analyzed with golden particle measurement system, which was consist of CVS (Constant Volume Sampler), particle number counter and particle number diluter.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.608-614
• /
• 2015

Nitrogen oxide(NOx) emission reductions are required to meet the strict emission regulations for environmental protection. Most of the Exhaust Gas Recirculation(EGR) system applied to a diesel engine can relatively decrease the NOx at a low cost, but it has a disadvantage in that the PM generation is promoted due to the hot intake air temperature. Thus, high heat exchange efficiency of the EGR cooler is required for an effective removal of NOx. In this study, heat exchange efficiency for various types of heat exchangers used in EGR cooler was measured under same conditions, and determined best heat exchange performance shape depending on type of heat exchanger.

• 한국추진공학회지
• /
• 제20권6호
• /
• pp.83-90
• /
• 2016

이중 모드 램젯 엔진 모델의 램젯 모드 연소 시험을 수행하였다. 엔진 모델은 흡입구, 연소기 및 노즐로 이루어졌다. 로켓 기반 복합 사이클 엔진에 사용하는 것을 전제로 큰 후향 계단을 가지는 형상을 선택하였다. 시험은 마하 5, 고도 24 km 조건에서 수행하였다. 연료를 카울면과 바닥면에 분산하여 다중 분사를 한 경우에 안정적인 연소를 달성할 수 있었다. 또한 연료 당량비를 카울면에서 0.5, 바닥면에서 0.5로 하여 총 당량비 1.0으로 한 경우에 연소기 내부에서 열질식이 발생하여 유동이 아음속으로 조성되는 램젯 모드로 운전됨을 확인하였다.