• 설비공학논문집
• /
• 제23권11호
• /
• pp.711-717
• /
• 2011

In this study, 5 types of PVS(Passive ventilation system) units are made and experimented its ventilation performance, thermal performance according to open rate and hole diameter of perforated aluminum plane. Results are as follows. 1) The ventilation performance increases approximately 50~70% according by the open rate of PVS increasing. Also, the ventilation performance increases about 2%~12% according by the hole diameter of PVS increasing. 2) In winter temperature/pressure condition(in : $20^{\circ}C$, out : $-2^{\circ}C/{\Delta}P$ : 0.2~5.0Pa) the temperature of inflow air decreases according by the open rate of PVS increasing. Heat gain performance decreases 10.1%, 25.6% when open rate increases 3) In the same condition, Heat gain performance decreases 18.3%, 18.8% according by the hole diameter of PVS increasing.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.749-752
• /
• 2004

In a liquid-fueled ramjet engine, the insufficient mixing and evaporation result in the low combustion efficiency and combustion instability. Improving its spray characteristics and devising a means of mixing fuel droplets with air may compensate these disadvantages of liquid fuel ramjet engine. The jet penetrations of various fuel injectors were measured to investigate the spray characteristics of a liquid-fueled ramjet engine under high pressure air-stream conditions. The penetrations in high pressure conditions are smaller than the values calculated from Inamura's or Lee's equations, and, in the high pressure conditions, the jet penetrations are similar each other. In the dual hole injectors, the jet penetrations of rear orifice is rapidly increased due to the reduction of the drag, which is created by the jet column of front orifice. The jet penetration of rear orifice is increased because of the drag reduction created by the jet column of the front orifice. And, because of the drag reduction formed by the column of jet, the jet penetration in the rear orifice of dual hole injector is much larger than the jet penetration of single hole injector. As the distances of the orifice are increased, the jet penetrations of the rear orifice decrease.

• 대한기계학회논문집B
• /
• 제38권10호
• /
• pp.865-871
• /
• 2014

본 연구는 벤츄리 시스템을 미세기포 생성을 위한 공기공급 장치로 개발하는데 그 목표를 두고 수행하였다. 이를 위해 상용유동해석 프로그램인 ANSYS CFX-15를 사용한 전산 유동해석을 통해 기하학적 형상변화가 벤츄리 관 내 유동특성들에 미치는 영향을 규명하였다 그리고 공급공기를 공급하는 공기 공급관의 위치, 크기, 개수 등을 변수로 2-유체 유동 해석을 수행하여 이들 설계 값들이 공기 공급 특성에 미치는 효과를 규명하였다. 최종적으로 직경 비 ${\beta}=0.75$의 벤츄리 확대관이 시작되는 위치에 공기 공급 구멍을 설치할 경우 가장 많은 공기가 벤츄리 관으로 유입되는 것을 확인할 수 있었으며, 유입공기 공급구멍 개수 및 직경과 벤츄리 관 내 공급되는 공기량 사이에는 선형적인 관계가 성립됨을 확인하였다.

• 대한조선학회지
• /
• 제21권1호
• /
• pp.21-34
• /
• 1984

This paper is concerned with the experimental investigation of transverse vibration characteristics in water of rectangular plates having an inner free cutout. Systematic experiments are carried out to investigate effects of the surrounding water on the added mass and the natural frequency of the plates due to the changes of the aspect ratio, hole size and eccentricity. The main subject is the clamped rectangular plate with a circular hole. For the purpose of comparative evaluations, some other common-type boundary conditions and hole shapes such as ellipses and rectangles are also investigated. Some of the results obtain are as follows; 1) For each given aspect ratio of the plate, there is a hole area ratio which gives a minimum value of the nondimensional frequency parameter for each mode. The hole area ratio increases as the order number of the mode increases. 2) The nondimensinal mass-increment parameter decreases as the aspect ration or the order number of the mode increases. For each given aspect ratio, the parameter the fundamental mode decreases monotonically as the hole area ratio increase. In cases of the second and higher order modes, however, each mode has a hole area ratio which gives a maximum value of the parameter for each aspect ratio more then 2/3. 3) Comparing elliptic holes with rectangular ones with same hole area ratio, nondimensional frequency parameters are almost same for each given ratio of the shorter axises to the longer one. 4) The influences of difference in boundary condion on nondimensional frequency parameters in water are similar to those in air.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.145-153
• /
• 2020

The purpose of this study is to compare the injection and spray characteristics of single-hole GDI injectors using injection rate and mie-scattering spray images. Five types of single-hole injectors with different nozzle hole diameters were used, and the spray rate, spray tip penetration, spray area, and spray width were analyzed. As a result, the diameter of the nozzle hole had a direct effect on the injection and spray characteristics. It was confirmed that the larger the diameter of the nozzle hole, the higher the injection quantity, the spray tip penetration, the spray area, and the spray width. In addition, it was confirmed that the near-field spray, which has little influence of ambient air, has a great correlation with the injection rate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.5-6
• /
• 2007

• 한국소음진동공학회논문집
• /
• 제22권1호
• /
• pp.29-37
• /
• 2012

This paper is concerned with the natural vibration characteristics of a rectangular plate with a rectangular hole in contact with the water. The addressed problem was solved by using the Rayleigh-Ritz method combined with the Green function method. This study presents the numerical approach, numerical results and experimental results. In addition, the validity of the approximate formula which mainly depends on the so-called non-dimensionalized added virtual mass incremental factor and the natural mode shape change due to the presence of the water were investigated. Experiments were also carried out to validate theoretical results. The theoretical results are in good agreement with the experimental results. It was found that the effect of a square hole on the natural frequencies of the square plate in contact with water is different from the effect of a square hole on the natural frequencies of the square plate in air and the approximate formula can predict lower natural frequencies in water with a good accuracy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.867_868
• /
• 2009

Interior permanent magnet synchronous motor [IPMSM] which has high power density is applied to motor for Hybrid electric vehicle[HEV], Electric vehicle[EV], Fuel cell electric vehicle[FCEV] and electric home appliances. In order to improve efficiency performance of IPMSM, this paper presented a study by making a hole around air barrier. Because concentrated rib stress is distributed by suitable hole, the hole can reduce rib thickness of IPM rotor. And it can help decrease PM[Permanent Magnet] leakage flux. Saliency ratio($L_q/L_d$) is also increased by magnetic circuit change. For this study, structure analysis of rotor is performed by Ansys program.

• 한국분무공학회지
• /
• 제21권1호
• /
• pp.58-63
• /
• 2016

This study presents the dynamic characteristics of an impinging droplet on hydrophobic and hydrophilic surfaces with various texture area fractions. The flat surface was fabricated by using the drilling technique to make micro-meter hole-patterned surfaces, which shows hydrophobic textured surfaces. Moreover, the hydrophilic textured surfaces were manufactured by anodizing technique on the micro-meter hole-patterned surfaces to generate multi-layer surfaces. Impinging droplet experiments were conducted for various hole-patterned surfaces, with changing impact velocity and texture area fractions. It is observed that an anodizing technique increases wettability by decrease in hole diameter on the textured surfaces. However, micro-drilled surfaces decreases wettability because the hole diameter was so large that air can be trapped under the holes. In addition, the maximum spreading diameter decreases with the texture area fraction for the micro-drilled surfaces because of decrease in wettability.

• 화약ㆍ발파
• /
• 제29권1호
• /
• pp.1-9
• /
• 2011

에어데크 공법은 노천광 및 대규모 발파현장에서 널리 쓰이는 대표적인 발파기술 중 하나이다. 에어데크 공법의 효율성 극대화를 위해 그간 많은 연구와 실험이 이루어졌으며, 공내에서 어떠한 압력 거동을 일으키는가를 규명하기 위한 노력들이 있었다. 본 연구에서는 다양한 에어데크 조건하에서 각 에어데크 구간이 어떠한 압력의 차이를 일으키는가에 대해 수치해석적으로 분석하였고, 에어데크의 위치와 에어데크 구간의 길이에 대한 압력변화를 알아보았다. 기본적으로 모든 수치해석은 JWL 상태방정식을 사용하였으며 2차원 평면상에서 진행 하였다. 순수한 압력의 변화만을 관찰하기 위해 암반의 밀도와 강도만을 달리하고 모든 암반은 균질한 상태로 가정하였다.