• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1561-1569
• /
• 2000

Flying attitudes of the slider, which are flying height, pitch and roll, are affected by the air flow velocity, the skew angle, and the manufacturing tolerances. Traditional designs of the air bearing surface have considered only the flying performances for the variations in the air flow velocity and the skew angle, which are determined by the radial position. In this study, we present the new shape design of the air bearing surface by considering the track seek performance and the air bearing stiffness as well as the traditional design requirements. The optimization technique is used to improve the dynamic characteristics and operating performance of the newly proposed air bearing surface shape design further. The optimized configuration is obtained automatically and the optimally designed sliders show the enhanced flying and dynamic characteristics.

• 한국유체기계학회 논문집
• /
• 제14권1호
• /
• pp.5-10
• /
• 2011

MTG(Micro turbine generator) operating at 400,000 rpm is under development and the impact test rig to measure the dynamic stiffness and damping coefficient of air foil bearing for high speed rotor is presented in this study. The stiffness and damping coefficient of air foil bearing depending on the rotational speed can be measured easily and effectively by using the simple configuration of impact test rig which is composed of air gun, gap sensors and high speed motor. The estimation results of stiffness and dampling coefficient using least square estimation method is presented as well.

• 정보과학회지
• /
• 제26권11호
• /
• pp.65-74
• /
• 2008

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 하계학술발표대회 논문집
• /
• pp.135-135
• /
• 2007

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1579-1586
• /
• 2003

A gun-type burne. fur a LPG(Liquified Petroleum Gas) boiler was utilized for hydrogen combustion. The study was performed to obtain fundamental data prior to the design of a very low NO$\_$x/, hydrogen-fueled burner. First, numerical simulations were performed to predict mixing characteristics between air and fuel flows, and temperature distributions, etc. Experimental study was then performed to find out flame lengths, temperature distributions, and NO$\_$x/ concentrations. The results showed that a gun-type burner for a LPG boiler can be successfully used for hydrogen combustion without any major retrofitting. The hydrogen flame was very stable and 75 ppm of NO$\_$x/ in average was observed for the conditions considered in this study. Hydrogen combustion could be therefore a solution to avoid the problem of green-house gas(CO$_2$) if hydrogen becomes cost-effective.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.89-92
• /
• 2005

This study investigates influence of particle properties of crushed sand on the duality of concrete. The test shows that an increase of fineness modulus(FM) resulted in high slump and air contents, while compressive strength decreased due to decreased adhesion with reduction of surface area. As grain shape become rounder, the slump of concrete increased, due to reduction of internal friction, and increased air contents. The reduction of adhesion by abrasion of surface declined compressive strength during the process of manufacturing crushed sand. Increase of powder contents decreased slump and it also decreased air contents due to the effect of filling air void. In addition. using powder contents increased compressive strength, but could not find any difference of bleeding and tensile strength with particle properties.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2001년도 학술발표회 발표논문집
• /
• pp.275-280
• /
• 2001

The purpose of this study was to investigate the air flow characteristics of the rock bed storage for solar-heated greenhouse design. Heat storage material was gravels and experiments were performed under constant inside temperature condition. The experimental parameters were operation method and air flow rate of fan. It was resulted that the temperature and amount of heat stored in rock-bed increased as the increase of air flow velocity and were more influenced by operation of inlet fan than outlet fan.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.154-157
• /
• 2009

Fuel cell is spotlighted as next energy source of future. The fuel of vehicle will be changed from fossil fuel such as gasoline, diesel to hydrogen. Polymer electrolyte membrane fuel cell(PEMFC) will be used to fuel cell vehicle because of its suitability. PEMFCs need oxygen for cathode. Because PEMFCs in vehicle use air for oxygen, air pollutant will be effect to performance of PEMFC. In this study, we examine a type of filter and pollutant gas how can be effect to performance of fuel cell electric vehicle.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2011년도 춘계학술대회
• /
• pp.205-227
• /
• 2011

On this study, the test for air-purification was executed as using the UV lamp and the UV lamp on which the TiO2 catalyst had been deposited with glass fiber in the reactor chamber. It aimed at the basic data of air-purifier as assessing the features of removing abilities for various contaminants including CH3COOH, NH3, NO, and SO2 as varying the number of TiO2 coating, the wave of UV lamp, and the amount of additive CaO as variables.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.153-160
• /
• 2012

This paper is written for the development of boiler combustion air control algorithm of coal-fired power plant by the steps of design, coding and test. The control algorithms were designed in the shape of cascade control for two parts of air master, forced draft fan pitch blade by standard function blocks. This control algorithms were coded to the control programs of distributed control systems under development. The simulator for coal-fired power plant was used in the test step and automatic control, sequence control and emergency stop tests were performed successfully like the tests of the actual power plant. The reliability will be obtained enough to apply to actual site if the total test has been completed in the state that all algorithms were linked mutually. It is expected that the project result will contribute to the safe operation of domestic power plant and the self-reliance of coal-fired power plant control technique.