• Journal of agriculture & life science
• /
• v.50 no.2
• /
• pp.175-185
• /
• 2016

In this study, manufactured experimental pig house (two pig house) and compared the changes in internal temperature and energy depending on the application of UTC control system for their utilizing of them as basic data for maintaining proper conditions for feeding environment and reducing heating energy depending on the UTC control system and program development, prior to applying the UTC system into pig house, representative agricultural facility. The control system ranges T1~T4 which is made to control a total of five output signals O1~O5 in the way of On/Off by using the algorithms of the program after measuring temperature scored 4 of total. Temperature setting was controlled with 28.0℃ in experimental pig house and 34.0℃ in UTC plenum, and output signal was controlled by comparing it with the measured temperature. During 3 days, the maximum temperature were measured at an average 31.8℃ when operated the control system in pig house. At the same time, the maximum temperature were measured 36.6℃ in comparison pig house, it was low temperature at 4.8℃ in experimental pig house than comparison pig house. Also, UTC plenum temperature was showed that rose at an average 50.5℃ by operation of the control program.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.367-373
• /
• 2023

Aircrews and passengers are exposed to radiation from cosmic rays and secondary scattered rays generated by reactions with air or aircraft. For aircrews, radiation safety management is based on the exposure dose calculated using a space-weather environment simulation. However, the exposure dose varies depending on solar activity, altitude, flight path, etc., so measuring by route is more suggestive than the calculation. In this study, we developed an instrument to measure the cosmic radiation dose using a general-purpose Si sensor and a multichannel analyzer. The dose calculation applied the algorithm of CRaTER (Cosmic Ray Telescope for the Effects of Radiation), a space radiation measuring device of NASA. Energy and dose calibration was performed with Cs-137 662 keV gamma rays at a standard calibration facility, and good dose rate dependence was confirmed in the experimental range. Using the instrument, the dose was directly measured on the international line between Dubai and Incheon in May 2023, and it was similar to the result calculated by KREAM (Korean Radiation Exposure Assessment Model for Aviation Route Dose) within 12%. It was confirmed that the dose increased as the altitude and latitude increased, consistent with the calculation results by KREAM. Some limitations require more verification experiments. However, we confirmed it has sufficient utilization potential as a cost-effective measuring instrument for monitoring exposure dose inside or on personal aircraft.

• Convergence Security Journal
• /
• v.22 no.5
• /
• pp.95-105
• /
• 2022

The Army, Navy, and Air Force are making various efforts to develop a weapon system that incorporates the 4th industrial revolution technology so that it can be used in multi-domain operations. In order to effectively demonstrate the integrated combat power through the weapon system to which the new technology is applied, it is necessary to establish a network environment in which each weapon system can transmit and receive information smoothly. For this, it is essential to analyze the Information Exchange Requirement(IER) of each weapon system, but many IER analysis studies did not sufficiently reflect the various considerations of the actual tactical network. Therefore, this study closely analyzes the research methods and results of the existing information exchange requirements analysis studies. In IER analysis, the size of the message itself, the size of the network protocol header, the transmission/reception structure of the tactical network, the information distribution process, and the message occurrence frequency. In order to be able to use it for future IER prediction, we present a technique for calculating the information exchange requirement as a probability distribution using the Poisson distribution and the probability generating function. In order to prove the validity of this technique, the results of the probability distribution calculation using the message list and network topology samples are compared with the simulation results using Network Simulator 2.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5B
• /
• pp.497-507
• /
• 2010

Climate changes affect greatly natural ecosystem, human social and economic system acting on constituting the climate system such as air, ocean, life, glacier and land, etc. and estimating the current impact of climate change would be the most important thing to adapt to the climate changes. This study set the target area to Nakdong river watershed and investigated the impact of climate changes through analyzing precipitation tendency, and to understand the impact of climate changes on hydrological elements, analyzed elasticity of precipitation-streamflow. For the analysis of precipitation trend, collecting the precipitation data of the National Weather Service from major points of Nakdong river watershed, resampling them at the units of year, season and month, used as the data of precipitation trend analysis. To analyze precipitation-streamflow elasticity, collecting area average precipitation and long-term streamflow data provided by WAMIS, annual and seasonal time-series were analyzed. In addition, The results of this study and elasticity, and other abroad study compared with the elasticity analysis and the validity of this study was verified. Results of this study will be able to be utilized for study on a plan to increase of flood control ability of flooding constructs caused by the increase of streamflow around Nakdong river watershed due to climate changes and on a plan of adapting to water environment according to climate changes.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.4
• /
• pp.517-527
• /
• 2023

Objectives: We examine cases of chemical poisoning that occurred in the cleaning of metal parts and the regulations on halogenated solvents in other countries and propose regulations necessary to prevent chemical poisoning from halogenated solvents. Methods: We collected cases of chemical poisoning through the website of the Korea Occupational Safety and Health Agency. A review of the literature was conducted focusing on regulations related to halogenated solvents in the United States and the European Union, particularly for cleaning metal parts. Among the Material Safety Data Sheets submitted to the government, MSDS containing eleven substances were extracted to confirm the composition and product use. We investigated cleaning methods for metal parts used in South Korea. For the hazard classification, the European Chemicals Agency or Japan's NITE's website was used. Results: In the case of poisoning, the cleaning methods involving trichloromethane were dipping and dry, which was not found in the literature. It was confirmed that many halogenated solvents and dimethyl carbonate were used for metal cleaning in South Korea. In vapor degreasing using TCE in the USA, even if the facility is strictly managed, such as by installing cooling coils in open cleaning facilities, the risk of exposure to TCE is considered to be not only carcinogenic but also a concern for acute and chronic effects. In comparison, exposure through Korean work methods such as dipping and drying operations is inevitably much higher. Conclusions: The transition to water-based cleaning with low-hazard chemicals should be a priority in the cleaning process. In the case of metal parts that require precise cleaning, if the use of a halogenated solvent is inevitable, a closed degreasing facility should be used to minimize exposure. The current regulations in the Occupational Safety and Health Act, the Chemical Substances Control Act, and the Air Environment Conservation Act do not require cleaning facilities to minimize emissions. To protect the health of workers using halogenated solvents to clean metal parts, regulations that require a fundamental reduction in exposure will be necessary.

• Journal of Korea Port Economic Association
• /
• v.39 no.3
• /
• pp.47-60
• /
• 2023

A thorough inventory of ship emissions, particularly ship's emission of in-port area is necessary to identify significant sources of exhaust gases such as NOx, SOx, PM, and CO₂ and trends in emission levels over time, and reduce their serious effects on the environment and human health. Therefore, the goal of this study is to assess the volume of emissions from ships in Mokpo port, which serves as a gateway to the southwest coast of Korea, using a bottom-up methodology and data from the automatic identification system (AIS) and the Korean Port Management Information System (Port-MIS). In this work, an analysis of ship movement utilizing AIS data and an actual set of data on ship specification were gathered. By examining ship movement using AIS data, We also proposed a new approach for identifying cruising/maneuvering mode. Finally, the results were classified by ship operating mode, by exhaust gas, by ship type, and by berth, which provides a thorough and in-depth analysis of the air pollution caused by ships in Mokpo port.

• Journal of Venture Innovation
• /
• v.5 no.2
• /
• pp.85-99
• /
• 2022

Dryers becoming commercially available for experimental and industrial use are classified to general drying oven, hot-air dryer, vacuum dryer, freezing dryer, etc. and kinds of them are various from the function, size and volume, etc. But the moisture measurement is not applied although it is important factor for the quality control and the performance improvement of products, and then now is very passive because the weight is weighed arbitrarily after dry-end. Generally the method for measuring moisture is divided by a direct measurement method and a indirect measurement method, and the former such as the change of weight or volume on the front and rear of separation of moisture, etc. is mainly used. Relatively a indirect measurement is very limited to apply due to utilize measurement apparatuses using temperature conductivity and micro-wave etc. In this research, we easily designed the moisture measurement system using the open-source based Arduino, and monitored moisture fluctuations and weight profiles in the real-time without the effect of external environment. Concretely the temperature-humidity and load cell sensors were packaged into a drying oven and the various change values were measured, and their sensors capable to operate 60℃ and 80℃ were selected to suitable for the moisture sensitive materials and the food dry. And also the performance safety using the organic samples of banana, pear, sawdust could be secured because the changes of evaporation rate as the dry time and temperature, and the measurement values of load cell appeared stable response characteristics through repeated experiments. Hereafter we judge that the reliability can be improved increasingly through the expansion of temperature-humidity range and the comparative analysis with CFD(Computational Fluid Dynamics) program.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.34 no.1
• /
• pp.85-97
• /
• 2024

Objectives: This study was intended to investigate the revision status of the occupational exposure standards for aluminum at home and abroad; to investigate worker exposure at domestic aluminum manufacturing and handling workplaces; to conduct social and economic evaluation for the revision of domestic aluminum exposure limits. Methods: We investigated the current status of occupational exposure limits for aluminum at home and abroad, and analyzed supporting data. An exposure survey was conducted targeting domestic aluminum manufacturing and handling workplaces. Based on these, revised aluminum occupational exposure limits were proposed. Results: The major aluminum exposure limits at home and abroad show a notable difference. The toxicity of aluminum, which was revealed through animal experiments and epidemiological investigations. The average concentration of aluminum in the air at 12 workplaces was 0.016 mg/m³, and the maximum was 0.0776 mg/m³. When total dust and respiratory dust were measured side by side and simultaneously for the same process, 12.1% of the total mass concentration of aluminum dust was respiratory dust. As a result of measuring and comparing the size distribution of dust with an optical particle counter in real time, 48.1% of the total dust in the form of welding fume and pyro-powder was respiratory dust. Based on the literature review and workplace survey, three proposals for changing the aluminum exposure limit were proposed. Proposal (1): For all types, 10 mg/m³ is unified as the exposure limit except for soluble salts and alkyls. Proposal (2): 1(R) mg/m³ as the exposure limit for all forms except soluble salts and alkyl. Proposal (3): 1(R) mg/m³ for pyro-powder and welding fume, and 10 mg/m³ for metal dust, aluminum oxide, and insoluble compounds as exposure standards. A pyro-powder was defined as dry aluminum powder of 200 mesh size (74 ㎛) or smaller (larger size classified as metal dust). Reason for setting: In the workplace survey, the ratio of respiratory dust to total dust was analyzed to be about 1:10, so it was judged that the domestic standard and the ACGIH standard were compatible. Conclusions: In all scenarios according to the revision of the exposure standard, the B/C ratio was greater than 1 or only benefits existed, so it was evaluated as sufficiently reasonable as a result of the socio-economic evaluation.

• Journal of Adhesion and Interface
• /
• v.25 no.2
• /
• pp.56-62
• /
• 2024

In this study, LiDAR-detectable black hollow-structured materials are synthesized using different reducing agents to evaluate their applicability to LiDAR sensor. Initially, white SiO₂/TiO₂ core/shell (WST) materials are fabricated via a sol-gel method, followed by a reduction using ascorbic acid (AA) and sodium borohydride (SB). After the reduction, subsequent etching of the SiO₂ core leads to the formation of two different black hollow-structured materials (AA-BHT and SB-BHT). The lightness (L^*) and near-infrared (NIR) reflectance (R%) of AA-BHT are measured as ca. 19.1 and 34.5 R%, and SB-BHT shows values of ca. 11.5 and 31.8 R%, respectively. While AA-BHT exhibits higher NIR reflectance compared to SB-BHT, it displays slightly lower blackness. Compared with core/shell structured materials, improved NIR reflectance of both AA-BHT and SB-BHT is attributed to the morphology of hollow- structured materials, which increase light reflection at the interface between air and black TiO₂ according to the Fresnel's reflection principle. Consequently, both AA-BHT and SB-BHT are effectively detected by the commercially available LiDAR sensors, validating their suitability as black materials for autonomous vehicle and environment.

• The Korean Journal of Air & Space Law and Policy
• /
• v.28 no.2
• /
• pp.295-347
• /
• 2013

Korea launched the science satellite by the first launch vehicle Naro-ho(KSLV-1) at the Naro Space Center located at Oinarodo, Cohenggun Jellanamdo in August, 2009 and October, 2010. However, the first and second launch failed. At last, on January 30, 2013 the third launch of the launch vehicle Naro-ho has successfully launched and the Naro science satellite penetrated into the space orbit. Owing to the succeed of the launch of Naro-ho, Korea joined the space club by the eleventh turn following the United States, Russia, Japan and China. The United Nations adopted the Outer Space Treaty of 1967, the Rescue Agreement of 1968, the Liability Convention of 1972, the Regislation Convention of 1976, and Moon Agreement of 1979. Korea ratified the above space-related treaties except the Moon Agreement. Such space-related treaties regulate the international liability for the space activity by the launching state of the space object. Especially the Outer Space Treaty regulates the principle concerning the state's liability for the space activity. Each State Party to the Treaty that launches or procures the launching of an object into outer space is internationally liable for damage to another State Party or to its natural or judicial persons by such object or its component parts on the earth, in air space or in outer space. Under the Liability Convention, a launching state shall be absolutely liable to pay compensation for damage caused by its space object on the surface of the earth or to aircraft in flight. The major nations of the world made national legislations to observe the above space-related treaties, and to promote the space development, and to regulate the space activity. In Korea, the United States, Russia and Japan, the national space-related legislation regulates the government's liability of the launching state of the space object. The national space-related legislations of the major nations are as follows : the Outer Space Development Promotion Act and Outer Space Damage Compensation Act of Korea, the National Aeronautic and Space Act and Commercial Space Launch Act of the United States, the Law on Space Activity of Russia, and the Law concerning Japan Aerospace Exploration Agency and Space Basic Act of Japan. In order to implement the government's liability of the launching state of space object under space-related treaties and national legislations, and to establish the standing as a strong space nation, Korea shall improve the space-related policy, laws and system as follows : Firstly, the legal system relating to the space development and the space activity shall be maintained. For this matter, the legal arrangement and maintenance shall be made to implement the government's policy and regulation relating to the space development and space activity. Also the legal system shall be maintained in accordance with the elements for consideration when enacting the national legislation relevant to the peaceful exploration and use of outer space adopted by UN COPUOS. Secondly, the liability system for the space damage shall be improved. For this matter, the articles relating to the liability for the damage and the right of claiming compensation for the expense already paid for the damage in case of the joint launch and consigned launch shall be regulated newly. Thirdly, the preservation policy for the space environment shall be established. For this matter, the consideration and preservation policy of the environment in the space development and use shall be established. Also the rule to mitigate the space debris shall be adopted. Fourthly, the international cooperation relating to the space activity shall be promoted. For this matter, the international cooperation obligation of the nation in the exploration and use of outer space shall be observed. Also through the international space-related cooperation, Korea shall secure the capacity of the space development and enter into the space advanced nation.