• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.490-498
• /
• 2010

The optimum mold design and the optimum process condition were constructed upon executing process simulation of rubber injection molding with the commercial CAE program of MOLDFLOW(Ver. 5.2) in order to solve the process-problems of K company relating to air-traps and short-shots. The former occurs at the cavity edge of torque-rod-bush and the latter takes place for the injection molding of dynamic dampers. As a result the process problem relating to air traps was solved by optimizing edge-angle and the number of gates to prevent the flow congestion of flow-front and to make the flow-front movement unaffected by congestion. For dynamic dampers of K company the unmolded flaw caused by their unfilled cavity was corrected by installing the air-vent at the confronting locations of both upstream and downstream of flow-front where air traps frequently occur. Besides the unmolded flaws were rectified by altering the position of gate from the upper to the middle or by increasing the number of gates. Thus the process problems of K company relating to air-traps and short-shots of torque-rod-bush and dynamic dampers, respectively, were solved by proper altering of mold design with process simulation of rubber injection molding.

• The Korean Journal of Ecology
• /
• v.21 no.6
• /
• pp.809-814
• /
• 1998

Changes of annual seed production related to climate change were studied for 12 years in Piagol, a riparian valley in Mt. Jiri. Sixty-four seed traps (sized 0.5 ${\times}$ 0.5 $m^{2}$) were set up on the forest floor of surveyed area. Seeds were collected from these traps at an interval of 15 days from September to November since 1984. Vegetation of the study area was mainly consisted of the naturally regenerated Carpinus tschonoskii in the tree layer. Acer mono, Quercus serrata, Carpinus laxiflora and Symplocos chinensis also appeared in the same layer. Maximum production occurred in 1984 and 1994. As a result of comparing seed production with local climate factors for 12 years, seed productivity and the year of maximum production of Carpinus forest were merely related with precipitation, air temperature and duration of sunshine among local climate factors. Duration of sunshine was, however, not contributed to periodically high productivity of seed of riparian valley carpinus forest.

• Parasites, Hosts and Diseases
• /
• v.47 no.2
• /
• pp.159-165
• /
• 2009

House-residual spraying and insecticide-treated bed nets have achieved some success in controlling anthropophilic and endophagic vectors. However, these methods have relatively low efficacy in Korea because Anopheles sinensis, the primary malaria vector, is highly zoophilic and exophilic. So, we focused our vector control efforts within livestock enclosures using ultraviolet black light traps as a mechanical control measure. We found that black light traps captured significantly more mosquitoes at 2 and 2.5 m above the ground (P<0.05). We also evaluated the effectiveness of trap spacing within the livestock enclosure. In general, traps spaced between 4 and 7m apart captured mosquitoes more efficiently than those spaced closer together (P>0.05). Based on these findings, we concluded that each black light trap in the livestock enclosures killed 7,586 female mosquitoes per trap per night during the peak mosquito season (July-August). In May-August 2003, additional concurrent field trials were conducted in Ganghwa county. We got 74.9% reduction (P<0.05) of An. sinensis in human dwellings and 61.5% reduction (P>0.05) in the livestock enclosures. The black light trap operation in the livestock enclosures proved to be an effective control method and should be incorporated into existing control strategies in developed countries.

• Journal of ILASS-Korea
• /
• v.23 no.2
• /
• pp.81-89
• /
• 2018

The objective of this study is to estimate the level of exposure of traffic-related air pollutants (TRAPs) on the pedestrians in Seoul area. The road network's link-based pollutant emission was calculated by using a set of mobile source emission factor package and associated activity information. The population information, which is the number of pedestrian, was analyzed in conjunction with the link-based traffic emissions in order to quantify exposure level by selected 23 spots. We proposed the Exposure Intensity, which is defined by the amount of traffic emission and the population, to quantify the probability of exposure of pedestrian. Link-based traffic NOx and PM emissions vary by up to four times depending on the location of each spot. The Hot-spots is estimated to be around 1.8 times higher Exposure Intensity than the average of the 23 selected spots. The information of Exposure Intensity of each spot allows us to develop localized policies for air quality and health. Even in the same area, the Exposure Intensity over time also shows a large fluctuation, which gives suggestions for establishing site-specific counter-measures.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.276-279
• /
• 2008

Air stable n-type organic field effect transistors (OFETs) based on CB60B are realized using a perfluoropolymer as the gate dielectric layer. The devices showed the field-effect mobility of $0.05\;cm^2P/V\;s$ in ambient air. Replacing the gate dielectric material by $SiO_2$ resulted in no transistor action in ambient air. Perfluorinated gate dielectric layer reduces interface traps significantly for the n-type semiconductor even in ambient air.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.85-90
• /
• 2011

In this paper a design procedure via computer-aided molding simulation is presented to optimize the air-trap locations in a speaker encloser of mobile phone. The molding flow simulation reveals that the race-tracking phenomenon is the dominant feature in the current mold design. In obtaining an optimal filling pattern, the local modifications of the wall thickness such as in a flow leader attachment are considered as the primary control factor, and both the gate position and the filling time become the secondary control factor. In the one-at-a-time approach, the last location to be filled in the mold cavity could be successfully moved to the extremities of the part, allowing a natural ventilation of entrapped air through the mold parting plane.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.4
• /
• pp.32-37
• /
• 2010

One of the most common engineering processes using plastics is the injection molding. In addition, plastics are utilized over the entire areas in our life including cars and home appliances among others for their characteristics with no deterioration even after a long time, as well as for their light weights in addition to their good durability. This paper aimed to minimize defects through prior analyses on the weld line, air traps, filling time, molding temperature and deformation patterns among others while carrying out interpretations on the cooling, filling and deformation in the injection process using the moldflow for rear lamp reflectors among components for a car in making parts through the coating process after injection.

• Environmental Engineering Research
• /
• v.12 no.5
• /
• pp.203-210
• /
• 2007

Since the emissions composition from the household products have potentially been associated with health risks for building occupants, the chemical composition emitted from the products should be surveyed. The current study identified the emission composition for 42 liquid household products, using a purge-and-trap method. This evaluation was done by classifying the household products into five product classes (deodorizers, household cleaners, color removers, pesticides, and polishes). Nineteen compounds were chosen on the basis of selection criteria. The quality control program for purge-and-trap and analytical systems included tests of laboratory blank Tenax traps and blank water samples, and the determination of calibration equation, measurement precision, method detection limit (MDL), and recovery. The number of chemicals varied according to the product categories, ranging from 4 for the product category of bleaches to 12 for the product categories of air fresheners and nail color removers. For all product categories, the emission composition and concentrations varied broadly according to product. It is noteworthy that most household products emit limonene: 19 of 25 cleaning products; 5 of 6 deodorizers; 1 of 3 pesticides; 3 of 3 color removers; and 4 of 5 polishes. It was suggested that the use of household products sold in Korea could elevate the formation of secondary toxic pollutants in indoor environments, by the reaction of limonene with ozone, which entered indoor environments or might be generated by indoor sources such as electronic air cleaning devices and copying machines.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1438-1440
• /
• 1998

In this work, simultaneous measur of space charge and conduction current was c out in LDPE with air gap by Pulsed-Electro-Aco Method. Also, effect of long time charging at con electric field on the formation of space charge conduction was investigated. From the experim results. we knew that the homo space charge formed near the dielectric surfaces and moving the bulk of dielectric as the electric field elevated. This was related with the deep traps b carriers and de trapping by Poole-field lowering conduction current was coincident with the Pool emission. From the long time charging experimen obtained the results that the negative space was moving into the dielectric bulk as the cha continued and the positive space charge accumulated at upper surface of LDPE.