• Nuclear Engineering and Technology
• /
• 제48권2호
• /
• pp.457-469
• /
• 2016

During the late phase of severe accidents of light water reactors, a porous debris bed is expected to develop on the bottom of the flooded reactor cavity after breakup of the melt in water. The geometrical configuration, i.e., internal and external characteristics, of the debris bed is significant for the adequate assessment of the coolability of the relocated corium. The internal structure of a debris bed was investigated experimentally using the DAVINCI (Debris bed research Apparatus for Validation of the bubble-Induced Natural Convection effect Issue) test facility. Particle sedimentation under the influence of a two-phase natural convection flow due to the decay heat in the debris bed was simulated by dropping various sizes of particles into a water vessel with air bubble injection from the bottom. Settled particles were collected and sieved to obtain the particle mass, size distribution in the radial and axial positions, and the bed porosity and permeability. The experimental results showed that the center part of the particle bed tended to have larger particles than the peripheral area. For the axial distribution, the lower layer had a higher fraction of larger particles. As the sedimentation progressed, the size distribution in the upper layers can shift to larger sizes because of the higher vapor generation rate and stronger flow intensity.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.51-61
• /
• 2012

The new alkali pulping process combined with electron beam treatment was applied to utilize hemp bast tissues as a new valuable fibrous resource. Hemp bast tissues have some chemical properties with high lignin contents and holocellulose not to be defiberized by alkali pulping only, compared with the bast tissue of paper mulberry. To make up for the weakness of traditional alkali pulping process, electron beams were directly irradiated into the swelled bast tissue of hemp in NaOH solution and distilled water, and then facilitated the defiberization of hemp bast tissues. The papermaking from hemp bast fibers manufactured by the combination pulping process showed good apparent density, formation structure and air permeability, and had some mechanical properties with lower tensile, tear, burst strength and folding endurance. It is finally concluded that the combination pulping process with electron beam treatment could be suggested a new alternative for non-woody fibers.

• 펄프종이기술
• /
• 제46권5호
• /
• pp.9-18
• /
• 2014

London Convention on the prevention of marine pollution by dumping of wastes and other matter prohibits the deliberate disposal of paper mill sludges at sea. In order to explore the alternative plan on the prohibition of sludge disposal at sea, the biodegradable seedling pot was developed by mixing the sludge with old newspaper (ONP) in appropriate mixing ratios. The C/N ratio of the mixed sludge was below 20, leading to rapid deterioration of the organic matters composing the seedling pot. The increased ONP contents in the seedling pot resulted in the increase of pot thickness and thereafter in the decrease of pot density. Cellulose fibers in ONP promoted water absorption of the pot but AKD addition helped the seedling pot to repel water during raising seedling. Breaking length and burst strength of the seedling pot were improved by addition of wet strength additives but air permeability was a little diminished. Biodegradable rate of the seedling pot in a soil was accelerated by the attack of soil microbes at the beginning, and finally the pot was completely degraded in 150 days in a soil.

• 패션비즈니스
• /
• 제12권3호
• /
• pp.116-135
• /
• 2008

To investigate the actual distribution condition and clothing construction factors of the working clothes supplied to the Changwon national industrial complex, 5 major companies in machinery, automotive, industrial engineering, shipbuilding and rolling stock in the industrial complex located in Gyeongsangnam-Do were selected. The questionnaire designed for the research consisted of working clothes distribution policies in manufacturing industry and the actual conditions of the design facts, repair and maintenance of the working clothes, etc. The analysis of the clothing construction factors of the working clothes provided by 5 respondent companies were conducted in parallel. The results derived from the study were as follows: The basic types of working clothes were the blouson jacket and straight pants; safety equipments for manufacture were safety helmets, gloves, snickers, goggles, masks, ear caps, wristlets, leggings, apron, etc. The size-charts adopted by the participant companies were the small-medium-large and cm/inch measurement size systems. To solve wearer's dissatisfaction with the garment fit, certain clothing construction factors were used, e.g. strap bands and the elastic band on a waist band. The types of fabrics used for the working clothes were mainly polyester/cotton and polyester/rayon blended ones. Moreover, to provide with more air permeability to wearers, the warp knit material was used to construct the lining and the armpit or back bodice slits. Lock, two-thread chain, safety, overedge stitches were applied with flat, lap felled, French, superimposed, lapped, bound and edge finishing seams to construct the working clothes selected.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2018년도 학술발표회
• /
• pp.228-228
• /
• 2018

강변여과는 지하수 인공함양 방식 중 유도함양(induced recharge) 또는 간접함양 방식에 속한다. 이는 하천 및 강변 부근에 집수시설을 설치한 후, 미고결층 대수층(unconsolidated aquifer)의 자연 오염 저감능을 이용하여 지표수를 간접 취수하는 방식으로 수질이 불량한 지표수가 대수층을 관류하면서 희석, 화학적 이온 교환 및 반응, 흡착, 생물막(biofilm; 미생물에 의한 자연저감), 여과 등을 통하여 수질이 개선된다. 강변여과수내의 용존 농도가 높은 철과 망간은 수처리 비용증가, 용수관정 및 시설물의 수명단축을 초래한다. 따라서 강변여과 지역의 미고결 대수층에서 효과적인 철과 망간 동시 제거(vyredox)를 위해 에어서징(air surging)과 블록 서징(block surging)을 실시하기 위해서 실내 물탱크 모델(water tank model)에서 에어서징에 따른 공기 순환 우물시스템을 관찰하였으며, 이를 바탕으로 현장시험(Test bed)에 적용하였다. 미고결 대층수층에서의 철 망간은 음용수 기준치(각각 0.3 mg/L)를 초과하고 있으며, 강변여과 취수 개발 및 이용을 제한하는 요인이 되고 있다. 본 연구에서 사용된 에어서징과 블록서지 기술은 자갈층 및 미고결 대수층에 충진된 슬라임 및 폐색(clogging)을 제거함과 동시에 관정 주변의 대수층의 투수성 개선과 산화환경으로 치환되며, 대수층에 잔존하는 철/망간의 산화물들을 관정내로 빼낼 수 있는 방법이다. 따라서 서징에 따른 폐색 제거효율을 검토한 결과에서 철 망간 이온농도 저감효과와 관정 주변의 수리전도도(hydraulic conductivity) 및 저류계수(coefficient of storage)가 증가한 것으로 나타났다. 이와 같이 강변여과에 의한 폐색은 미고결층내 공기주입 및 블록서지를 통하여 철/망간 이온농도 저감 및 수리특성 개선 효과에 유용한 것으로 평가된다.

• 한국산학기술학회논문지
• /
• 제20권7호
• /
• pp.265-271
• /
• 2019

본 논문의 목적은 기존의 에틸렌기반 폴리머 사용 배합인 투수 콘크리트 단점을 개선하고자, 아크릴 폴리머를 적용함으로써 개선된 도로 포장 재료로써 활용하기 위한 기초자료를 제시하고 한다. 기존의 에틸렌 폴리머 기반 투수 콘크리트 재료를 선정하고, 아크릴 폴리머를 혼입하여 배합 설계하여 비교 평가하였다. 시험결과, 기존 에틸렌 기반 폴리머 투수 콘크리트 배합 경우 큰 공극률이 발생하여 압축강도 증진이 미약한 결과를 나타냈었고, 아크릴 폴리머 기반 투수 콘크리트 배합 경우 KS에서 규정하고 있는 차도용 28일 압축강도 24MPa을 만족하였다. 휨강도인 경우, 아크릴 폴리머 기반 투수 콘크리트 배합 강도가 우수하였으며, 투수 계수는 모든 변수에서 기준인 0.1(mm/s) 이상으로 측정되었다. 흡수율의 경우 모든 변수에서 1% 이하로 측정되었고, 동탄성계수 측정결과, 아크릴 폴리머배합특성의 경우 120 Cycle 이상 측정을 유지할 수 있었고, 다른 배합의 경우 80 Cycle 이상 유지하지 못하였다. 따라서 기존의 에틸렌 폴리머 기반보다 아크릴 폴리머를 적용함으로써, 내구성 향상에 효과적인 것으로 판단된다.

• 한국염색가공학회지
• /
• 제33권2호
• /
• pp.87-95
• /
• 2021

In this study, the application of a medical compression sleeve of Moisture Responded Transformable(MRT) fibers to the treatment of lymphedema after surgery in breast cancer patients was investigated. MRT fibers were manufactured with PET and Nylon6 bi-component cross-section yarns, and compression sleeves of sleeves 1, 2, 3, and 4 were knitted in order of size, and then the physical properties and clinical tests were evaluated. As a result, the pressure of compression sleeve in wrinkle was the lowest in sleeve 1 with 3.81 kPa, and the highest in sleeve 4 with 5.22 kPa. Elastic recovery rate is that all parts except the top of the sleeve 1 exhibited 100%. The air permeability was good at 12.1 ~ 16.1 cm³/cm²/sec, and peeling was also comparatively excellent as grade 3. In addition, the weight of the compression sleeves 1, 2, and 3 decreased as 18.3 ~ 23.0 g/m² depend on size, while the compared sample was heavier with 17.39 ~ 32.61 g/m². In lymphoscintigraphy test, it was confirmed that the function of remaining lymph node was good in all patients. Although there were no differences between samples in skin irritation and tightness in wearing comfort, the manufactured sleeves showed better fit, lightness, fashion and breathability than the comparable sleeves.

• 한국염색가공학회지
• /
• 제34권1호
• /
• pp.38-45
• /
• 2022

Sound absorbing materials are being developed in various materials and shapes and they are being applied in many fields such as construction, transportation, civil engineering, and sound. Among many sound-absorbing materials, polyester fiber has no environmental problems and harmfulness, and is a material with good sound absorption properties while being inexpensive. So it is manufactured as a nonwoven sound-absorbing material and used in various fields. In this study, polyester dry-laid nonwoven with different basis weight were manufactured using three types of polyester staple fibers: regular solid, single-hole hollow, and low linear density. We focused on the effects of the properties of the fibers, which constitute nonwovens, on the sound absorption properties, and we considered the basis weight. As the basis weight of the nonwoven fabric increased, the pore size became smaller and the air permeability was lowered, but the sound absorption coefficient was higher. However, the single-hole hollow polyester fiber did not contribute to the increase of the sound absorption coefficient of the nonwoven. It was established that, lower fiber fineness caused the sound absorption coefficient of the nonwoven to be increased. It was also found that the increase in the sound absorption coefficient due to the application of low fineness appeared from a certain basis weight or more.

• Advances in concrete construction
• /
• 제13권4호
• /
• pp.315-325
• /
• 2022

Reinforced concrete structures are exposed throughout their lifetime to the phenomenon of carbonation, which considerably influences their durability by causing corrosion of the reinforcements. The fight against this phenomenon is usually ensured by anti-carbonation coatings which have the possibility of limiting the permeability to carbon dioxide or with coatings which absorb the CO₂ present in the air. A coating with good crack-bridging (sealing) capacity will prevent water from entering through existing cracks in concrete. Despite the beneficial effect of these coatings, their durability decreases considerably over time with temperature and humidity. In order to use coatings made from local materials, not presenting any danger, available in abundance in our country, very economical and easy to operate is the main objective of this work. This paper aim is to contribute to the formulation of a corrected dune sand-based mortar as an anti-carbonation coating for concrete. The results obtained show that the cement mortar based on dune sand formulated has a very satisfactory compressive strength, a very low water porosity compared to ordinary cement mortar and that this mortar allows an improvement in the protection of the concrete against the carbonation of 60% compared to ordinary cement mortar based on alluvial sand. Moreover, the formulated cement mortars based on dune sand have good adhesion to the concrete support, their adhesion strengths are greater than 1.5MPa recommended by the standards.

• 복식문화연구
• /
• 제31권2호
• /
• pp.262-276
• /
• 2023

This study aims to develop a multi-functional cage for dogs as a house to reduce their anxiety when they go out using cages. This study investigates the types and characteristics of cages and cage preference by surveying men and women in their 20s who use them. The cage product reviews are also analyzed. The research results are as follows: First, domestic dog cages are classified into crate, shoulder, cross (sling bag), backpack, carrier, and stroller types. The crate type is easy to clean and can be used as a house, but it is bulky and therefore inconvenient to carry when using public transportation. The shoulder type is a fabric material with good air permeability but has the disadvantage of being easily soiled. It can be used as a house and is light weight, making it convenient when using public transportation. Second, as a result of consumer research, respondents prefer the shoulder-type fabric over the crate-type plastic material. Third, from the shoulder-type product review, the shape stability, companion dogs' psychological safety, the wearability of companions, and management convenience are derived. Fourth, based on the survey results, a multi-functional cage is developed taking into account the companion dog, companion person, and functional factors.