• 동력기계공학회지
• /
• 제19권2호
• /
• pp.40-48
• /
• 2015

As advantages of LPG-DI engine, LPG is directly injected into combustion chamber during compression stroke to reduce compression temperature, prevent knock and spontaneous combustion, and adjust engine output using the amount of directly injected fuel, thereby reducing pumping loss caused by throttle valve. Stratified charge can be supplied nearby spark plugs to allow for overall lean combustion, which improves thermal efficiency and can cope with problems regarding emission regulations. In addition, it is characterized by free designing of intake manifold. Despite the fact that LPG-DI has many advantages as described above, there is lack of detailed investigation and study on spray characteristics, combustion flame characteristics, and ignition probability. In this study, a visualization experiment system that consists of visualization combustion chamber, air supply control system, emission control system, LPG fuel supply system, electronic control system and image data acquisition system was designed and manufactured. For supply of stratified charge in the combustion chamber, alignment of injector and spark plugs was made linear.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.70-83
• /
• 1997

We made a selection of engine operating conditions in the natural aspiration type diesel engine as load and speed. The effects on the power, smoke emission and cylinder pressure characteristics of these variations in operating conditions were observed experimentally. Also, the smoke emission was predicted by using the Arrhenius equation and empirical equation of the smoke emission was made. At the same time, the correlations, between the combustion and smoke emission characteristic were examined. From the above results, it is clear that to prevent power dropping and to decrease exhaust fume whin the conditions are changed, one should improve the intake system. To do this, the best way is to lower the air-fuel mixing ratio. We found that the parameters of the indicated mean effective pressure, maximum pressure and its location and combustion duration, etc. change the motion in accordance with the conditions described above. Also, we found that the variation of the pressure cycle comes from an amplified variation of the early part of process. From the analysis of comparing combustion and exhaust fume, the exhaust fume is produced at the latter time of combustion and decreased when the combustion ratio is higher. Also, we developed a special formula which can predict the exhaust fume value according to the engine load and speed.

• 한국자동차공학회논문집
• /
• 제2권1호
• /
• pp.38-50
• /
• 1994

To improve the efficiency of internal combustion engines, it is necessary to understand mixed air-fuel in-cylinder flow processes accurately at intake and compression strokes. There is experimental and numerical methods to analyse in-cylinder flow process. In numerical method, standard $k-{\varepsilon}$ model with wall function was mostly adopted in in-cylinder flow process. But this type model was not efficiently predicted in the near wall region. Therefore in the present study, low Reynolds number $k-{\varepsilon}$ model was adopted near the cylinder wall and standard $k-{\varepsilon}$ model in other region. Also QUICK scheme was used for convective difference scheme. This study takes axisymmetric reciprocating model engine motored at 200rpm with a centrally located valve, incorporated 60 degree seat angie, and flat piston surface excluding inlet port. Because in-cylinder flow processes are undergoing unsteady and compressible, averaged cylinder pressure and inlet velocity at arbitrary crank angle are determined from thermodynamic analytic method and incylinder states at that crank angle are iteratively determined from the numerical analytic method.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.584-587
• /
• 2011

마하 5 스크램젯 엔진에 대하여 연소 시험에 대한 예비 시험 성격으로서 연료 분사 없이 내부 유동 공력 시험을 수행하였다. 엔진은 흡입구 크기 $70mm{\times}200mm$, 전체 길이 1.7m의 시험용 모델을 대상으로 하였다. 설비는 한국항공우주연구원이 자체 설계 개발하여 보유한 불어내기식 극초음속 시험 설비를 사용하였다. 측정은 엔진 내부 유로를 따라 19개 지점에서 압력을 측정하였다. 시험 결과 본 엔진 모델을 사용하여 설비 시동이 가능하였으며 엔진 내부는 초음속 유동이 유지됨을 확인하였다.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.71-76
• /
• 2012

The aim of this work was to investigate the combustion and nanoparticle emission characteristics of premixed charge compression ignition (PCCI) combustion at various test conditions using a single cylinder common-rail diesel engine. In order to create the homogeneity of fuel-air mixture, the premixed fuel (gasoline) was injected into premixing chamber during the intake process and then the diesel fuel was directly injected into the combustion chamber as an ignition source for the gasoline premixture. From these results, it revealed that the ignition delays and combustion durations were gradually prolonged and the peak combustion pressure were increased because diesel fuel was injected early injection timing with the increase of premixed ratio. In addition, as the increase of premixed ratio, total particle number is generally decreased and particle volume also indicated low levels at the direct injection timing from BTDC $20^{\circ}$ to TDC. At further advanced injection timing, total particle number and volume were generally increased

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.94-99
• /
• 2012

The characteristics of spray behavior and injected amount were studied with two types of nozzles for using in a compression ignition engine with dual fuel technology for construction machines. A penetration length of spray tends to shorten due to a decrease of injected amount of a diesel fuel with dual fuel engine application. In order to ignite the gaseous fuel premixed with air during intake process, a diesel fuel, which was compression ignited, needs to penetrate somehow similar depth compared with the case of a diesel fuel-only-injection. In this work, a nozzle with reduced hole diameter and increased number of holes was tested and demonstrated that, compared to diesel 100% case, its penetration lengths are comparable to 74% and 79%, respectively, of those of 100% and 50% supply of a diesel fuel with the baseline nozzle that has four holes and 30.4% increased diameter. This will presumably enhancement the combustion in a dual fuel engine. A design suggestion was also made in this work to achieve similar penetration length of spray with diesel 100% case to prevent combustion from being deteriorated in a dual fuel engine.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.481-488
• /
• 1998

In recently, lots of researcher have been attached to develope various alternative fuels and to use renewable fuels for solution of the exhaust emission problems. In this study, the usability of used vegetable oil as alternative fuel for diesel engines has been investigated. This paper was compared with the exhaust emissions and performance in diesel engine with used vegetable oil and conventional diesel fuel. Since the vegetable oil includes oxygen of about 10%, it influenced the combustion process strongly. So, the smoke emissions of used vegetable oil were exhausted to be lower than those of diesel fuel. Also, the used vegetable oil was much the same cycle to cycle variation with diesel fuel except $P_{(dP}$d.theta.)max/, but the cycle to cycle variation of used vegetable oil was reduced significantly by preheating of the fuel and swirling of the intake air. It was concluded that used vegetable oil could be utilized effectively as renewable fuel for diesel engine.e.

• Asian-Australasian Journal of Animal Sciences
• /
• 제6권2호
• /
• pp.253-258
• /
• 1993

The study on the nutritive value and the potential use of two kinds (local vs. import) of sesame meal (SSM) in layer diets as substitute for soybean meal (SBM) at 25, 50, and 75% was carried out. Three hundred and thirty six layers were kept individually on a battery cage and fed isonitrogenous diets, 16% crude protein (CP), for 252 days. The local and the imported SSM contained on air dry basis 35.7 and 36.3% CP, 24.7 and 9.1% ether extract (EE), respectively. Their amino acid contents are all lower than those reported by NRC (1984). The local material contained remarkably lower lysine (0.44 vs. 0.94), methionine + cystine (1.06 vs. 1.75) and threonine (0.52 vs. 1.22) than the imported meal. Imported SSM could be substituted for SBM as high as 50% in layer ration without statistically adverse effect on egg production, feed intake, body weight gain, average egg weight and egg size, while local SSM was inferior to the control in all aspects. However, when production performance of the groups fed either kind of SSM was compared, no significant difference was found at the two lower substitution levels.

• 한국분무공학회지
• /
• 제11권1호
• /
• pp.17-23
• /
• 2006

The influence of fuel spray characteristics on engine performance has been known as one of the major concerns to Improve fuel economy and to reduce exhaust emissions. In general, the UBHC(Unburned Hydrocarbon) emission could be reduced by decreasing the droplet size of the fuel sprays. In PFI (Port Fuel Injection) gasoline engines, the mixture of air and fuel would not be uniform under a certain condition, because the breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve sheat. In this study, were investigated the transient spray characteristics and dynamic behavior of droplets from 2holes-2sprays and 4holes-2sprays type injectors used in PFI gasoline engine. Mean droplet size and optical concentration were measured by LDPA (Laser Diffraction Particle size Analyzer). The variation of droplet mean diameter and optical concentration were measured for understanding the behavior of unsteady spray.

• 한국분무공학회지
• /
• 제25권2호
• /
• pp.45-50
• /
• 2020

Recently, global warming and environmental pollution are becoming more important, and fuel economy is becoming important. Each automobile company is actively developing various new technologies to increase fuel efficiency. CVVD(Continuously Variable Valve Duration) system means a device that continuously changes the rotational speed of the camshaft to change the valve duration according to the state of the engine. In this paper, VVT(Variable Valve Timing) and CVVD were applied to a single-cylinder diesel engine, and the characteristics of intake and exhaust flow rate and in-cylinder pressure characteristics were analyzed by numerical analysis. In order to analyze the effect of CVVD on the actual engine operation, the study was performed by setting the valve control and injection pressure as variables in two sections of the engine operating region. As a result, In the case of applying CVVD, the positive overlap with the exhaust valve is maintained, thus it is possible to secure the flow smoothness of air and increase the volumetric efficiency by improving the flow rate. The section 2 condition showed the highest peak pressure, but the pressure rise rate was similar to that of the VVT 20 and CVCD 20 conditions up to 40 bar due to the occurrence of ignition delay.