• 대한건축학회논문집:구조계
• /
• 제34권8호
• /
• pp.19-27
• /
• 2018

In this study, annual site and primary energy use intensities (EUIs) and $CO_2$ emission intensities (CEIs) per area by end use were estimated based on the measurement data from June 2016 to May 2017 of 19 sample office buildings in Seoul. In addition, the estimated site EUIs by end use were compared to the U.S. Commercial Buildings Energy Consumption Survey (CBECS) 2012 data. Average site EUIs by end use were found to be in the order of electric appliance (typical floors) > heating > cooling > lighting > air movement > domestic hot water > vertical transportation > city water supply. In the case of primary EUIs and CEIs by end use, electric appliance was found to be the largest. As results of comparison with the CBECS 2012 data, it was found that the site EUIs were similar for heating, cooling, domestic hot water, and electric appliance, etc., but slightly different for lighting and air movement. The number of sample office buildings will continue to increase until 2020 (total number of samples 85) and intensities data by end use will be continuously updated through continuous collection of measurement data.

• Journal of Preventive Medicine and Public Health
• /
• 제39권2호
• /
• pp.171-176
• /
• 2006

Objectives : The objective of this study is to assess the factors influencing biological monitoring of textile coating factory workers exposed to N,N-dimethylformamide(DMF). Methods : We studied 35 workers who were occupationally exposed to DMF from 9 textile coating factories. The study was carried out in two phases; summer and winter. While air concentration of DMF, temperature and humidity were assessed in order to monitor the atmospheric conditions, biological monitoring was done to determine the internal dose by analyzing the N-methylformamide(NMF) collected from urine at the beginning and end of the shift. Questionnaires and medical surveillance were also obtained during the two phases. Results : Median air concentrations of DMF in winter and summer were 1.85 ppm and 2.78 ppm respectively. Also the difference between the urinary NMF concentration at the beginning and end of the shift $({\Delta}NMF)$ was always significant in each season (P < 0.001). The correlations between log DMF in air, log end-of-shift urinary NMF (r=0.555, P < 0.001) and log ${\Delta}NMF$ (r = 0.444, P < 0.001) was statistically significant in summer. The temperature, humidity, a shift system and different styles of clothing worn were significantly different during the two phases. In a multivariate analysis, temperature and the concentration of DMF in the air were the main factors influencing biological monitoring of textile coating factory workers. Conclusions : Concerning more comprehensive prevention measures to reduce exposure for those workers occupationally exposed to DMF, dermal exposure conditions such as temperature and humidity together with the air concentration of DMF should be assessed and biological monitoring is necessary to reduce adverse health effects, especially during the summer.

• 한국연초학회지
• /
• 제22권2호
• /
• pp.114-122
• /
• 2000

This study was carried out to investigate the changes in the composition of essential oils for the improvement of air-curing process of burley tobacco leaves. From the essential oils isolated from the cured tobacco leaves by steam distillation method, 90 compounds including 15 acids and esters, 19 alcohols, 23 aldehydes and ketones, 19 hydrocarbons, and 14 miscellaneous compounds, could be identified by gas chromatography and gas chromatography-mass spectrometry. Among them, acids and esters were gradually decreased during the progress of curing after harvesting. A rapid increase in alcohol content was observed in the earlier stage of curing, but thereafter, decrease followed until the end of curing However, aldehyde and ketone groups were continuously increased during curing and were 3 times higher in quantity after curing than at the harvesting time. The concentration of hydrocarbons was increased in the earlier stage of curing, but gradually decreased from the middle stage. The miscellaneous compounds were continuously increased in content until the end stage of curing, with rapid increased in the earlier stage of curing.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.227-230
• /
• 1999

In this paper, the machining characteristics of high speed ball end milling affected by the rotational error of high speed spindle using air bearing are investigated. The error motions of a spindle have generally influenced on the surface roughness, the form accuracy, the tool life, etc. in end milling. Experiments are carried out over a wide range of rotational speeds(10,000-50,000rpm). The rotational errors of the spindle are measured by the gap sensor mounted on the spindle shaft at various cutting speeds. The relations between the surface roughness and the spindle error motion are presented. Results show that the rotational accuracy of the spindle directly affects the surface roughness of the machined surface.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 하계학술발표 논문집
• /
• pp.33-33
• /
• 2004

• 대한임베디드공학회논문지
• /
• 제15권1호
• /
• pp.25-33
• /
• 2020

Multipath routing protocols with unmanned aerial vehicles have been proposed to improve reliability in tactical ad hoc networks. Most of existing studies tend to establish the paths with multiple metrics. However, these approaches suffer from link loss and congestion problems according to the network condition because they apply same metric for both ground and air path or employ the simple weight value to combine multiple metrics. To overcome this limitation, in this study, we propose new routing metrics for path over unmanned aerial vehicles and use the multi-criteria decision making (MCDM) method to determine the weight factors between multiple metrics. For the case studies, we extend the ad-hoc on-demand distance vector protocol and propose a strategy for modifying the route discovery and route recovery procedure. The simulation results show that the proposed mechanism is able to achieve high end-to-end reliability and low end-to-end delay in tactical ad hoc networks.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권3호
• /
• pp.282-290
• /
• 2013

A primary air pollutant as an indicator of air quality released from incomplete combustion is Carbon monoxide. A study of the distributions of CO concentration with no heat source in a tunnel model closed at left end side is simulated with a commercial CFD code. The tunnel model is used to investigate the CO concentration distributions at three Reynolds numbers of 990, 1970, and 3290. which are computed by the inlet velocities of 0.3, 0.6 and 1.0 m/s. The CFD predictive approaches can be useful for a better design to analyze the distributions of CO concentrations. In the case of the tunnel model closed at left end side alone, the concentration changes of x/H=-5 and -2.5 have the similar laminar characteristics like the case of the tunnel model closed at both end sides expecially at low values of Reynolds number. Irregular average CO concentration variations at Re=1790 are considered that the transition from laminar to turbulent flow occurs even in three different tunnel models.

• 대한기계학회논문집B
• /
• 제20권3호
• /
• pp.1061-1073
• /
• 1996

Vortex tube is a simple device which splits a compressed gas stream into a cold stream and a hot stream without any chemical reactions. The phenomena of energy separation taking place in a vortex tube has been investigated experimentally. Recently, vortex tube is widely used to local cooler of industrial equipments and air conditioner of special purpose. In this study, experimental study on vortex tube efficiency was performed with various cold end orifices and nozzles type. The experimental results indicate that there is an optimum diameter of cold end orifice and nozzle type for the best cooling performance. The variation of the maximum wall temperature along the vortex tube surface provides useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. The similarity relation for the prediction of the temperature of the cold exit air was obtained.

• 대한전자공학회논문지SD
• /
• 제39권9호
• /
• pp.11-18
• /
• 2002

본 논문에서는 표면 마이크로머시닝을 사용하여 10 ${\mu}m$ 두께의 다공질 실리콘 산화막으로 제조된 기판 위에 에어브리지를 가진 CPW phase shifter와 shunt stub을 제작하였다. CPW phase shifter의 크기는 S-W-$S_g$ = 100-30-400 ${\mu}m$로 설계되었다. “ㄷ” 모양을 가진 에오브리지의 폭은 100 ${\mu}m$, 길이는 400-460-400 ${\mu{m$ 이다. 낮은 손실을 얻기 위하여, step 된 에어브리지를 가진 CPW phase shifter가 제안되었다. Step된 에어브리지를 가진 구조가 step이 없는 에어브리지를 가진 구조보다 삽입손실이 보다 더 향상되었다. 제작된 CPW phase shifter의 위상특성은 28 GHz의 넓은 주파수 범위에서 180$^{\circ}$ 의 천이를 나타내었다. 그리고 short-end series stub의 동작주파수는 28.7 GHz이며, 반사손실은 - 20 dB를 나타내었다. 또한 short-end shunt stub의 동작주파수는 28.9 GHz이며, 반사손실은 - 23 dB를 나타내었다. 이상의 결과에서 중앙 전송선에 설계된 stub은 크기 감소로 고 밀도 칩 레이아웃을 이끌 수 있는 장범을 가진다.

• Corrosion Science and Technology
• /
• 제19권4호
• /
• pp.196-202
• /
• 2020

The air vent connected to a heat supply pipeline in the district heating system has been used to eliminate the existing air in the pipe, which has a detrimental effect on corrosion durability and heat efficiency. Recently, the air vent installed under a manhole for 22 years was corroded and several pinholes were detected in the front-end of the air vent. To identify the cause of the failure, thickness reduction, corrosion products, and water quality were examined. The corrosion damage was significant at the outside of the front-end of the air vent where the insulator was covered. While a thin oxide layer was formed in the interior of the tube, the coarse and porous corrosion products consisting of magnetite and hematite were found externally. Water flowing into the thermal insulator was absorbed by the insulator following hydrolysis. The hydrolyzed insulator ejected the corrosion factors such as Cl^-, SO₄^2-, and NH₄⁺. The findings suggest that the corrosion under insulation due to rain water is the main cause of the underlying failure in the air vent.